Wholesale Beds CHARLES User manual

ASSEMBLY INSTRUCTIONS
PAGE 1 OF 12
CHARLES 3 + 2 DRAWER CHEST SEC/SH/11/16/EU1
IMPORTANT
PLEASE READ BEFORE YOU CONTINUE FURTHER
THE PRODUCT YOU HAVE PURCHASED WILL GIVE YOU MANY
YEARS OF SERVICE IF YOU FOLLOW THE GUIDELINES FOR ITS
SAFE ASSEMBLY AND PERIODIC MAINTENANCE AND CLEANING.
ASSEMBLE ON A SOFT CLEAN SURFACE.
DO NOT USE ANY TOOLS OTHER THAN THOSE SHOWN.
ANY SPANNERS OR ALLEN KEYS REQUIRED ARE INCLUDED WITH
THE FITTINGS KIT.
DO NOT FOR ANY REASON USE A POWER TOOL TO ASSEMBLE
THIS PRODUCT.ITS USE WILL INVALIDATE ANY CLAIM YOU MAY
HAVE AND COULD MAKE THIS PRODUCT UNSAFE.
DEPENDING ON THE AMOUNT OF USE THIS PRODUCT RECEIVES
IT MAY BE NECESSARY TO TIGHTEN UP THE FIXINGS FROM TIME
TO TIME.THIS IS COMPLETELY NORMAL FOR ANY FLAT PACK
FURNITURE.DO NOT OVERTIGHTEN FIXING.
FOR CLEANING,YOU MAY USE A DAMP CLOTH (NOT WET) DO NOT
USE POLISH,DETERGENT OR CHEMICAL CLEANERS.
THE SURFACE OF THIS ITEM IS NOT HEAT RESISTANT.ALWAYS
USE A PLACE MAT UNDER HOT OR COLD ITEMS TO PREVENT
MARKING.
FOR DOMESTIC USE ONLY

NB ( 0.35 )
UY ( 0.53 )
NB UY
PAGE 2 OF 12
SEC/SH/11/16/EU1
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
( SCREWDRIVER NOT PROVIDED )
USE A FLAT HEAD SCREWDRIVER TO TIGHTEN THE CAM NUTS. A QUARTER TURN CLOCKWISE IS ALL THAT IS NEEDED.
STEP 1 - PUSH CAM BOLT INTO INSERT
STEP 2 - ALIGN THE CAM BOLT WITH THE HOLE AND PUSH TOGETHER UNTIL FLUSH. ( MAKE SURE THE ARROW OF
CAM LOCK IS POINTING TOWARD THE HOLE ON EDGE OF PANEL. )
STEP 3 - THE HEAD OF THE BOLT GOES INTO THE WIDE MOUTH OF THE CAM LOCK.YOU THEN TURN THE LOCK SO
THE NARROW PART CLOSES OVER THE BOLT.

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 3 OF 12
SEC/SH/11/16/EU1
PLEASE CHECK THAT YOU HAVE ALL THE PARTS LISTED BEFORE YOU START
ASSEMBLING.IF YOU DO FIND THAT SOMETHING IS MISSING,DO NOT CONTINUE
ASSEMBLY,PLEASE CONTACT YOUR SUPPLIER IMMEDIATELY.
PARTS LIST PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
INNER TOP PANEL
CENTRE DRAWER DIVIDE
UPPER FRONT CROSSBAR
CENTRE FRONT CROSSBAR
BASE PANEL
LOWER BASE CROSSBARS
BACK PANEL
SMALL DRAWER BACK
TOP PANEL
DRAWER SIDE - LEFT
DRAWER SIDE - RIGHT
1 PC
1 PC
1 PC
1 PC
1 PC
1 PC
2 PCS
1 PC
1 PC
1 PC
2 PCS
2 PCS
5 PCS
5 PCS
1 PC
LEFT SIDE PANEL
CENTRE BACK CROSSBAR
16
SMALL DRAWER FRONT - LEFT
SMALL DRAWER FRONT - RIGHT 1 PC
RIGHT SIDE PANEL
17 SMALL DRAWER BASE 2 PCS
18 LARGE DRAWER BACK 3 PCS
19 LARGE DRAWER FRONT 3 PCS
20
21
LARGE DRAWER BASE
LARGE DRAWER BOTTOM SUPPORT RAIL
3 PCS
3 PCS
1
10
11
11
8
9
3
5
67
7
12
4
12
13
14
15
17
16
17
13
14
19
13
20
18
14
2
21

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 4 OF 12
SEC/SH/11/16/EU1
HARDWARE LIST
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
57 PCS
18 PCS
74 PCS
3 PCS
12 PCS
20 PCS
45 PCS
10 PCS
10 PCS
5 PCS
10 PCS
1 PC
2 SETS
10 SETS
1 PC
2 PCS
2 PCS
DOWEL 6 X 30MM
BOLT M7 X 60MM
SCREW M3.5 X 16MM
SCREW M4 X 50MM
SCREW M4 X 30MM
SCREW M4 X 38MM
TACK
DRAWER RUNNER A
DRAWER RUNNER B
HANDLE
HANDLE SCREW 30MM
PLASTIC H STRIP
EDGE PROTECTOR
CAM BOLT + CAM NUT
ALLEN KEY
ANTI - TIP STRAP
SCREWB M4 X 16MM

TW ( 0.32 )
TW
VA
VB
VC
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 5 OF 12
SEC/SH/11/16/EU1
STEP 1 STEP 2
YOU WILL NEED:- YOU WILL NEED:-
C
H
32 PCS
8 PCS
A3 PCS
SCREW MUST BE INSERTED IN THE FIRST
HOLE ON THE DRAWER RUNNER
C8 PCS
A
H2 PCS
FRONT BACK
UP SECOND HOLE
FIRST HOLE
LAST FOURTH HOLE
SCREW MUST BE INSERTED IN THE
FIRST HOLE ON THE DRAWER
RUNNER
SCREW MUST BE INSERTED IN THE THIRD HOLE
ON THE DRAWER RUNNER
FRONT BACK
UP FIRST HOLE
FIRST HOLE
FRONT BACK
UP SECOND HOLE
THIRD HOLE
LAST SECOND HOLE
C
H
C
H
C
H
4
9
2
LAST FOURTH HOLE

VF ( 0.3 )
VG ( 0.2 )
VD
VE
VF
VG
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 6 OF 12
SEC/SH/11/16/EU1
STEP 3
STEP 4.1
YOU WILL NEED:-
YOU WILL NEED:-
A28 PCS D3 PCS
STEP 4.2
A
A
A
D
1
6
7
7
8
10
3
5
6
7
7
7
6
1
2
3
10
2
3

NN
TT
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 7 OF 12
SEC/SH/11/16/EU1
STEP 5 STEP 6
B 9 PCS
B9 PCS
YOU WILL NEED:- YOU WILL NEED:-
O1 PC
B
O
B
O1 PC
O
1
2
3
4
5
8
7
6
7
1
2
3
4
5
8
6
7
7
9

VL ( 0.3 )
RF
UL
VH
VJ
VK
VL
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 8 OF 12
SEC/SH/11/16/EU1
STEP 7 STEP 8.1
YOU WILL NEED:-
E 6 PCS
YOU WILL NEED:-
C4 PCS
G
L
M
16 PCS
1 PC
2 SETS
BACK SIDE VIEW
PLEASE INSERT THE BACK PANEL INTO THE UNIT
G
4
L
STEP 8.2
BEFORE FIXING THE TOP PANEL
PLEASE ALIGN THE TOP PANEL
WITH THE INNER TOP PANEL .
SIDE VIEW
A
E
C
M
BOTTOM
1
2
3
10
9
5
6
7
8
10
1
4 & 9
1
10
4 & 9
11
11 11
11
11
11
11

PC ( 0.13 )
PD ( 0.18 )
PE ( 0.23 )
PK ( 0.24 )
RP ( 0.18 )
TG ( 0.13 )
TH ( 0.13 )
PCPD
PE
PK
RP
TG
TH
UP
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 9 OF 12
SEC/SH/11/16/EU1
A8 PCS
YOU WILL NEED:-
C
F
G
12 PCS
8 PCS
8 PCS
I
J
K
4 PCS
2 PCS
4 PCS
F
A
IC
N
N
N4 SETS
R
A
2 X SMALL DRAWERS
K
STEP 9.1
STEP 9.2
STEP 9.3
STEP 9.4
G
I
I
J
12 13
14
15 & 16
17
17
15 & 16
15 & 16
13 & 14
12
13 & 14
15 & 16
STEP 9.5
BACK
FRONT
LAST THIRD HOLE
THIRD HOLE

VM ( 0.15 )
VN ( 0.2 )
VP ( 0.25 )
VR ( 0.2 )
VT ( 0.2 )
VU ( 0.2 )
VV ( 0.23 )
VW ( 0.2 )
VM
VN
VP
VR VT
VU VV
VW
CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 10 OF 12
SEC/SH/11/16/EU1
YOU WILL NEED:-
A
C
E
F
G
I
J
K
N
18 PCS
18 PCS
6 PCS
12 PCS
21 PCS
6 PCS
3 PCS
6 PCS
6 SETS
3 X LARGE DRAWERS
A
C
E
A
F
G
I
I
I
K
N
N
STEP 10.1
STEP 10.2
STEP 10.3
STEP 10.4
STEP 10.5
J
18
14
13
19
20
21
13 & 14
13 & 14
18
19
19
19
20
21
21
19
BACK
FRONT
LAST THIRD HOLE
THIRD HOLE

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 11 OF 12
SEC/SH/11/16/EU1
STEP 11 STEP 12
15
16
19
19
19

CAUTION : THE USE OF POWER TOOLS TO ASSEMBLE THIS PRODUCT WILL INVALIDATE
ANY CLAIM AND MAY DAMAGE THIS PRODUCT MAKING IT UNSAFE.
PAGE 12 OF 12
SEC/SH/11/16/EU1
WARNING
Serious or fatal injuries can occur from furniture tipping
over. To prevent the furniture from tipping over we
recommend that it is permanently fixed to the wall.
Wall fixings are not supplied with this product as different wall
materials require different types of fixing devices.Please make
sure you use fixings suitable for the walls in your home.
HARDWARE LIST
( P ) Anti-Tip Strap - 2 pcs
( Q ) M4 X 16MM - 2 pcs
TOP
WALL
TOP
WALL
TOP
P
P
Q