wildkin Olive Kids Bench Seat User manual
Assembly Procedure:
- Prior to assembling each wooden part, liberally apply the Wood Glue from the supplied bottle (o1) to both wooden
parts. After assembly (and before glue dries) wipe off any excess glue. While not absolutely necessary, the glue will
add additional strength to each joint, and is recommended.
* Please note that the shape of your chair back (D)
may be slightly different than the drawing.
Page 1 of 6
Thank you for purchasing this Bench Seat with
Storage! We know that it will bring you and your
little one years of enjoyment! Please first be sure
you have all the necessary components listed on
page 2. We suggest that you lay them all out on
the carpet before assembling. If for any reason
you think a component may be missing, please
contact our customer service team. Please read
the General Safety Instructions and Assembly
Procedure below before beginning assembly.
General Safety Instructions
- Your bench is safety tested for all ages, however it is recommended that caution be used at all times.
- This item is recommended for children up to 100 lbs.
- This item must be assembled by an adult. Please do not leave any spare parts near children.
- CAUTION: Although a safety hinge is installed, be careful when opening and closing the lid to avoid injury to small
children.
Tools You Will Need
- Standard Phillips Head Screwdriver. CAUTION: It is highly recommended that you not use power tools or electric
screwdrivers as screws should not be over-tightened.
Care Instructions:
- We recommend this item be wiped down with a non-bleach wipe.
Bench Seat Assembly Instructions
ADULT ASSEMBLY REQUIRED.
SMALL PARTS AND SHARP POINTS MAY BE PRESENT PRIOR TO ASSEMBLY.
KEEP OUT OF BABY’S REACH.
WARNING:
Components
A Base Board
Page 2 of 6
Bench Seat Assembly Instructions
B Right Side Board C Left Side Board
G Back Board
* Please note that the shape of your chair back
(D) may be slightly different than the drawing.
* Please note left and right arm
rest are labeled as if you were
sitting in the chair. “Bump” of the
arm rest should be facing out.
Front
Front
F Front Board
H Toy Box Lid D Seat Back
ER Right Arm
EL Left Arm
I Safety Hinge
Hardware Shown in Actual Size
s3 6- Short Machine Screw (1”)
s4 2- Sm. Machine Screw ( ”)
s1 2- Lg. Machine Screw (1 ”)
3
4
3
4
s5 2- Sm. Machine Screw ( ”)
1
2
o1 1- Wood Glue Bottle
w3 8- Sm. Washer ( ”)
5
8
w4 10- Spring Washer ( ”)
3
8
Page 3 of 6
1. Place Toy Box Lid (H) on the floor with the design facing up.
2. Insert the posts on the Seat Back (D) into the pre-drilled holes on the Toy Box Lid (H).
3. Insert machine screw (s3) through spring washer (w4) and small washer (w3) and tighten securely.
4. Insert machine screw (s4) into pre-drilled holes on
the back board (G) and secure the safety hinge by
tightening the screw.
5. Please see Figure 2 for proper alignment and
positioning of the safety hinge (I).
Bench Seat Assembly Instructions
Figure 1
Attach Chair Back (G) to Toy Box Lid (F).
Attach Safety Hinge (I) to Back Board (D)
Figure 2
H
D
w3 w4 s3
w3 w4 s3
H
D
G
s4
s4
I
Page 4 of 6
6. Remove the protective plastic strap from
the box lid and gently raise the hinged Lid (H)
until it comes in contact with the Seat Back
(D). Do not let the Lid (H) hit hard against the
Seat Back (D) because it may scratch or
damage it.
7. Lay the toy box lid assembly on a soft
surface with the seat back resting on the
floor. Place the Right Side Board (B) next to
the pre-drilled holes on the toy box lid.
8. Insert the 1” machine screw (s3) through
the spring washers (w4) and small washer
(w3) and tighten securely.
9. Repeat the procedure to assemble Left
Side Board (C).
10. Place the back board (G) on the assembly. Insert 1” machine screw (s3) through the spring
washers (w4) small washers (w3) and tighten securely into all pre-drilled holes.
Bench Seat Assembly Instructions
Figure 3
Attach Toy Box Lid (H) to Side Boards.
Attach Back Board (G)
Figure 4
G
BC
Dw3 w4 s3
w3
w3
w4
w4
s3
s3
w3
w4
s3
H
BC
w3
w3
w4
w4
s3
s3
Page 5 of 6
11. Be sure Lid (H) is laying flat against the
Seat Back (D). Insert 1/2” machine screw (s5)
into pre-drilled holes on the Safety Hinge (I).
12. Tighten screws securely. If the safety
hinge (I) is not connected to the lid, the lid
will fall by itself and may cause a danger to
children. After the safety hinge is assembled,
the lid will not fall by itself when it is opened.
13. Apply glue (o1) to the pre-drilled holes
on both ends of arm rests.
14. Align each Arm Rest (EL and ER) with
the pre-drilled holes on the Toy Box Lid (H)
and Seat Back (D).
15. Insert 1” machine screw (s3) through
spring washer (w4) and small washer (w3)
and tighten securely to attach each arm
rest to Lid (H).
16. Insert 1- 3/4” machine screw (s1)
through spring washer (w4) and small
washer (w3) and securely tighten to attach
each arm rest to Seat Back (D).
Bench Seat Assembly Instructions
Figure 5
Attach Safety Hinge (I) to Toy Box Lid (H).
Attach Arm Rests to the Toy Box Lid (H). Figure 6
H
I
C
B
s5
s5
H
D
EL
o1 ER
w3
w3
w4
w4
s1
w3
w4
s1
s3
Page 6 of 6
17. Line up the Front Board (F) with the
assembly. The thicker side should be on the
bottom.
18. Insert the 1” machine screw (s3) through
the spring washer (w4) and small washer
(w3) and tighten securely into all pre-drilled
holes.
19. Flip assembly so Seat Back (D) is resting
on floor as shown in Figure 8.
20. Attach the Base Board (A) to the
assembly.
21. Insert 1” machine screw (s3) through
spring washer (w4) and small washer (w3)
and tighten securely into all pre-drilled
holes.
22. Your storage bench assembly is
complete! Turn the bench over into an
upright position, and enjoy!
Bench Seat Assembly Instructions
Figure 7
Attach Front Board (F).
Attach the Base Board (A). Figure 8
D
H
C
F
ER
EL
w3
w4
s3
w3
w4
s3
w3
w4
s3
w3
w4
s3
A
F
C
D
w3
w4
s3
w3
w4
s3
Other wildkin Baby & Toddler Furniture manuals
