wildkin Vanity & Chair User manual
Thank you for purchasing a vanity set! To get started, please first be sure you have all the necessary components.
We suggest that you lay them all out on the carpet before assembling. If for any reason you think a component
may be missing, please contact our customer service team.
B2 Musical Box
(Right as you face the table)
*Please note: Your chair and
vanity might look slightly
different then the picture.
B1 Jewelry Box
(Left as you face the table)
Tools Needed for Assembly:
Standard Phillips Head Screwdriver. CAUTION: It is highly recommended that you not use power tools or electric
screwdrivers as screws should not be over-tightened.
General Safety Instructions:
Your vanity set is safety tested for 18-96 months. However, it is recommended that caution be used at all times.
Chairs are recommended for children up to 100 lbs.
Care Instructions:
Wipe clean with non-bleach cloth. If your item includes a cushion, please dry-clean cushion only.
Page 1 of 5
Vanity & Chair Assembly Instructions
ADULT ASSEMBLY REQUIRED.
SMALL PARTS AND SHARP POINTS MAY BE PRESENT PRIOR TO ASSEMBLY.
KEEP OUT OF BABY’S REACH.
PLASTIC BAGS CAN BE DANGEROUS. TO AVOID DANGER OF SUFFOCATION, KEEP THIS
BAG AWAY FROM BABIES AND CHILDREN.
WARNING:
s3 3- Medium Screws (1”)
Page 2 of 5
Components
Vanity & Chair Assembly Instructions
s2 2-Large Screws (1 ”)
1
4
C 1- Seat
A 1- Table Top
F 1- Mirror
(Mirror shape may vary.)
E 4- Table Legs
B2 1- Musical Box
B1 1- Jewelry Box
G 4- Chair Legs
D 1- Chair Back
(Chair back shape may vary.)
H 1- Seat Cushion
(Please note some designs do
not include cushion.)
I 1- Back Cushion
w1 2- Large Washers (1 ”)
1
4
w2 2- Medium Washers ( ”)
3
4
w3 3- Small Washers ( ”)
5
8
w4 5- Spring Washers ( ”)
3
8
s4 4- Small Screws ( ”)
3
4
Page 3 of 5
4. Position the pegs of the boxes (B1 & B2)
on Table Top (A) as shown in the figure.
5. Insert Small Screws (s4) into the holes
under Table Top (A) and secure them with
Phillips Head screwdriver until tight.
1. Set Table Top (A) upside down on a
soft floor surface to avoid scratching.
EE
A
A
E
E
E
E
B1
B2
s4 s4
EE
2. Insert each Table Leg (E) into one of
the four holes on the bottom of the
table and screw in until secure.
3. Be sure legs are secure, but not
overtightened.
Figure 2: Attach Jewelry Box & Musical Box to Table Top
Figure 1: Attach Table Legs to Table Top
Vanity & Chair Assembly Instructions
B2 B1
F
A
w3 w4 s3
E
EE
C
G
G
GG
E
Page 4 of 5
10. Set Seat (C) upside down on a soft
surface to avoid scratching.
11. Thread each Chair Leg (G) directly into
the hole on each corner of the Seat (C).
12. Tighten Chair Legs (G) securely.
6. Position the Mirror (F) to Table Top
(A).
7. Insert Medium Screw (s3) through
Spring Washer (w4) and Small Washer
(w3) as shown in the figure.
8. Screw with Phillips Head screwdriver
until tight.
9. Please unscrew plastic hooks on back
of Mirror (F) to remove protective
coating. After coating is removed,
tighten plastic hooks to secure mirror
in place.
Figure 4: Attach Chair Legs to Seat
Figure 3: Attach Mirror to Table Top
Vanity & Chair Assembly Instructions
D
C
w1w2w4s2
Figure 6: Attach Cushions
Page 5 of 5
13. Turn chair seat assembly over with
chair legs securely on the floor.
14. Insert Chair Back (D) posts into the
seat assembly through the pre-drilled
holes.
15. Insert Large Screw (s2) through
Spring Washer (w4), Medium Washer
(w2), and Large Washer (w1) as shown
in the figure.
16. Insert screw into the hole on the
bottom of the Chair Seat (C). Secure
screws with Phillips Head Screwdriver
until tight.
17. Tie Seat Cushion (H) to poles on
bottom of Chair Back (D) using tassels.
18. Attach Back Cushion (I) using velcro
on Chair Back (D).
Figure 5: Attach Chair Back
Vanity & Chair Assembly Instructions
Other wildkin Baby & Toddler Furniture manuals
