AFG RS628 User manual

3-in-1 Convertible Baby Crib (RS628)
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts
to the store from where it was purchased before contacting AFG Customer Service.
AFG Customer Service:
E-mail: [email protected]
Tel: (323) 722-6268
Model No.: RS628
PO #:
Serial #:

2020 AFG Baby Furniture RS628 Assembly Sheet © 2
Product Assistance Procedures
AFG International Products strives to ensure that our customers are receiving a quality piece of
furniture. We want our customers to be satisfied with using our products for years to come. In
the event that you need assistance or have any inquiries regarding our products, please feel
free to contact us with the information below.
Customer Service Email: service@afgbabyfurniture.com
Customer Service Phone Number: 1.323.722.6268
To request replacement parts, please send an email to our customer service with the
following information and we will do our best to assist you.
1. Proof of Purchase*
2. Item Number of the Product or Identification Sticker**
3. Part Letter or Number of the Replacement Part
4. Quantity
5. Your Shipping Address
6. Description of Your Problem
Please also provide pictures of the issue whenever possible. This will help us understand and
assist you with your problem.
*Acceptable Proof of Purchase includes, but not limited to, your Online Puchase Confirmation Email,
a screenshot of the purchase history of the online retailer, or a receipt from your local store.
Our warranty extends only to the original purchaser and is non transferable. Warranty is
valid only when the proof of purchase can be provided.
Please retain a copy of your purchase records for future inquires.
**All of our baby products come with an identification sticker. This is a white sticker that contains all the
product information of the item.
For cribs, the identification sticker is generally located near the bottom of the crib’s side rails, the toddler
guardrail, or the stabilizer bar.
For changers, the identification sticker is located on the top panel of the changing unit.
Under no circumstances should you remove any warning labels from the product. These labels
are meant to be permanent and removing them may damage the wood and void your Warranty.

2020 AFG Baby Furniture RS628 Assembly Sheet © 3

2020 AFG Baby Furniture RS628 Assembly Sheet © 4

2020 AFG Baby Furniture RS628 Assembly Sheet © 5
RS628 Parts Identification Sheet
DO NOT assemble crib if parts are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Parts
A. Headboard
(1 pc) B. Footboard
(1 pc) C. Back Stationary Side Panel (1
pc)
D. Front Stationary Side Panel
(1 pc) E. Stabilizer Bar
(2 pc) F. Mattress Support
(1 pc)
G. Guardrail
(not included, sold
seperately)
(1 pc)

2020 AFG Baby Furniture RS628 Assembly Sheet © 6
RS628 Hardware Identification Sheet
DO NOT assemble crib if parts are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Hardware
Item # Fittings Qty
1. Bolt M6 * 60mm (12 pcs)
2. Bolt M6 * 17mm (4 pcs)
3. Wrench (1 pc)
4. Barrel Nut (12 pcs)
5.. Wood Dowel 8 * 30mm (8 pcs)
6. Bolt M6 * 50mm (2pcs)
7. Bolt M6 * 45mm (2pcs)
PHILLIPS SCREWDRIVER (NOT INCLUDED)

2020 AFG Baby Furniture RS628 Assembly Sheet © 7
A. Headboard (1 pc) B. Footboard (1 pc)
C. Back Stationary Side Panel (1 pc) D. Front Stationary Side Panel (1 pc)
E. Stabilizer Bar (2 pc) F. Mattress Support (1 pc)

2020 AFG Baby Furniture RS628 Assembly Sheet © 8
RS628 Crib Assembly Sheet
STEP 1:
Insert 2 wood dowels (#5) on Back Stationary Side Panel, attach Headboard (A) and Footboard (B) to
Stabilizer Bar(E) by inserting 2 Barrel Nuts (#4) to the corners of the Stabilizer Bar(E) and install 2
Bolts (#1).
Insert 2 wood dowels (#5) on Back Stationary Side Panel, attach Headboard (A) and Footboard (B) to
Back Stationary Side Panel (C) by inserting 4 Barrel Nuts (#4) to the corners of the Back Stationary
Side Panel (C) and install 4 Bolts (#1). Tighten all bolts firmly with Wrench (#3).

2020 AFG Baby Furniture RS628 Assembly Sheet © 9
RS628 Crib Assembly Sheet
STEP 2:
Attach Mattress Support (F) by swinging out the four hangers at the corners of the mattress support
and use 4 Bolts (#2) to attach hangers to the brackets on the Headboard (A) and Footboard (B) at an
even level on all sides. Attach all parts Tighten all bolts firmly with Wrench (#3)..
Make sure that these bolts are tightly secured on even level.
Check components periodically, make sure mattress support’s hinges are been
tightened properly and securely.
Warning
Envelope
Face Up

2020 AFG Baby Furniture RS628 Assembly Sheet © 10
RS628 Crib Assembly Sheet
STEP 3:
Attach Stabilizer Bar (E) to Headboard (A) and Footboard (B) by inserting 2 wood dowel (#5) and 2
Barrel Nuts (#4) into Stabilizer Bar before securing 2 Bolts (#1). Tighten all screws firmly with Wrench
(#3).

2020 AFG Baby Furniture RS628 Assembly Sheet © 11
RS628 Crib Assembly Sheet
STEP 4:
Insert 2 wood dowels (#5) to top rail of Front Stationary Side panel (D), Attach Front Stationary Side
Panel (D) to Headboard (A) and Footboard (B) by inserting 4 Barrel Nuts (#4) from underside of each
corner of the Front Stationary Side Panel before securing 4 Bolts (#1), Tighten all screws firmly with
Wrench (#3).

2020 AFG Baby Furniture RS628 Assembly Sheet © 12
RS628 Crib Assembly Sheet
Complete.

2020 AFG Baby Furniture RS628 Assembly Sheet © 13
RS628 Day Bed Assembly Sheet
a. Loosen the Front Stationary Side Panel (D) bolts and detach the Front Stationary Side Panel (D)
from crib assembly.
b. Complete

2020 AFG Baby Furniture RS628 Assembly Sheet © 14
RS628 Toddler Bed Assembly Sheet
*Mattress Support Assembly must be in the lowest position before installing guardrail.
** Guard Rail(M) not included and sold separately.
Attach Guardrail (M) to Stabilizer Bar by using 2 bolts (#6) and left front leg by using 2 bolts (#7),
Tighten all screws firmly with Wrench (#3).
a. Complete.

2020 AFG Baby Furniture RS628 Assembly Sheet © 15
Safety Tips for Assembling and Re-assembling Cribs
Parents should not use any crib with missing, broken or loose hardware parts. Crib slats or spindles should be spaced
no more than 2-3/8” apart, and none should be loose or missing. NEVER use a crib with corner posts over 1/16” of an
inch above the end panels (unless they are over 16” high for a canopy).
Check this product for damaged hardware, loose joints, loosen bolts or other fasteners, missing parts, or sharp edges
before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use
crib if any parts are missing, damaged or broken. Contact (AFG International Products Inc.) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
Never place infants to sleep on pillows, sofa cushions, adult beds, waterbeds, beanbags, or any other surface not
specifically designed for infant sleep.
Always check all sides and corners of the crib to assure proper assembly with no openings that may entrap a child.
The crib mattress should fit snugly with no more than two fingers width, one-inch, between the edge of the mattress
and the crib side. Otherwise, the baby can get trapped between the mattress and the side of the crib.
Do not try to repair any side of the crib without manufacturer-approved hardware.
Putting a broken side up against the wall is not a solution and can often make the situation worse.
When re-assembling the crib for your second child, please keep in mind that the screw holes will need to be filled in
order for the screws to grip to the wood. Talk to your local hardware store or lumberyard about how to do it properly.
One year limited warranty
AFG International Products Inc. © wants you to be satisfied with any product that bears the AFG name or logo. We will
provide promptly, at the request of the retailer, and without charge, any missing parts that have been reported, with proper
description, within 7 days of the purchase of the products. Our warranty guarantees optimal workmanship and lack of
significant defects. The product warranty lasts a year from the date of your purchase. Please keep the original receipt so
that we may process your one year limited warranty request. This warranty only covers new units with original packaging.
Ownership of the warranty is non-transferable. The warranty does not cover any used, second-hand, or demo models. Our
obligation under this warranty is to replace or repair the merchandise, at our option, free of charge. This warranty does not
cover any damaged or defective parts that result from normal wear and tear, abuse, negligence, improper use or alteration
to the finish design, and hardware. Specific rights issued by this warranty may vary from state to state. Some states do not
allow limitations on how long implied warranties last. DO NOT return products to the store once a product is used, it cannot
be resold and the materials and energy invested in the product would go to waste. In the event that AFG determines that a
defect that may result from customer abuse or misuse, we will contact you with information about services and methods to
prevent occurrences. We strongly recommend you register your product with our company by filling out registration and
mailing it back to us. This ensures you are up-to-date with our products’ maintenance and information.
This warranty does not cover damage caused by accident, misuse or any use other than as intended and described in this
assembly sheet or damage resulting from failure to maintain and clean this product as specified in this assembly sheet.
This warranty applies only to the original purchaser of the AFG International Products Inc. product.
Care and Maintenance
Storage: The crib must be kept in a dry and clean area. Solid wood tends to exchange moisture with the surrounding
air and reacts to major changes in temperature and humidity. It is best to place your furniture away from heating or air-
conditioning vents. Direct exposure to sunlight can discolor of the wood, so do not place your product where it will
receive prolonged sunlight exposure.
Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild
soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be sure to use only a non-toxic
finish specified for children’s products.
Wood is a natural material. As such, it can be affected by changes in temperature and humidity. Extreme changes in
humidity and temperature can cause the wood to warp, swell, crack, or shrink, thus compromising the structural
integrity of the crib and making it dangerous to use.
CAUTION! Safety Tips for Use of Cribs
Many older cribs, including secondhand or second use cribs, may not meet all current safety
standards. For baby’s safety, even if you are on a tight budget, you should not purchase a used
crib at a garage sale or accept a hand-me-down that does not meet the most recent Federal and
ASTM standards.
Thank you for choosing AFG. MADE IN CHINA AFG ©
Table of contents
Other AFG Baby & Toddler Furniture manuals