Wind Crest SERIAL BUS User manual

Evacuation & Fire Fighting
Intercom System
TYPE: SERIAL BUS

IMPORTANT: READ PRIOR TO INSTALLATION
Each Landing Speaker supplied sh uld be installed n the designated
landing as they are pre-assigned a unique address (D n t change the address as
they are assigned fr m the fact ry. C ntact Windcrest bef re changing address).
The Master Switching Panel (with push butt ns f r each landing) sh uld be
installed n the main landing.
The EURO Switch has a set f c ntact (via multi-way cable) which can be
c nnected t the lift c ntr ller t place the lift in Evacuati n M de r Fire Fighting
M de. These c ntacts perate at the same time as the Evacuati n interc m is
switched ON.
The basic c nfigurati n f the system is that all the speakers are
interc nnected in a “Daisy Chain” starting f rm a P wer Supply B x.
T simplify the installati n, we rec mmend the use f RJ45 C nnect rs n the end
f CAT5 cable.
Check the RJ45 Cables with the RJ45 Cable tester pr vided with the Kit
bef re p wering up the system.
T interface the Serial Evacuati n System t an existing aut dialler, there
will be a need f Serial Car Speaker Interface Unit.
Windcrest
(UK) Ltd
Serial Evacuation & Fire
Fighting System
Drawing: Installation
03/09/10
Page 1
Tel: [phone]
Fax: [phone]

Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
E ample of Stand-alone
Serial Evacuation &
Fire Fighting
Intercom system
Drawing: SEREVA01 Block
19/09/13
Motor
Room
ALARM
2nd
1st
Gnd
Connector
nth Floor
Landing
Basement
Floors
To lowest Intercom unit
Address 01 and then going up
Main
Landing
230
VAC
Evacuati n
Interc m
P wer Supply
Shaft
Lift CAR
Top most landing
Bus 1
Page 2
N te: All the interc nnecti n cables
must be Screened and Twisted.
EVACUATION
INTERC OM
EVACUATION
INTERC OM
EVACUATION
INTERC OM
Patch Cable
Travelling Cable
EVACUATION
INTERC OM
EVACUATION
INTERC OM
Lift
Controller
Contacts
from Euro
Switch
FIRE FIGHTING
INTERC OM
Fire Fighting Interc m Operati n:
When the system is operated via turning
ON the Fire Fighting Switch on the panel,
a three way communication link will be
turned ON between the Panel, Motor
Room Speaker & the Lift Car Speaker.
“Press to speak” button is provided on the
Panel and on the Motor Room speaker to
communicate to the other speakers.
Turning OFF the Fire Fighting switch will
turn off the communication.
Evacuati n Interc m Operati n:
When the system is operated via turning
ON the Evacuation Switch on the panel, a
speech link can be provided to allow
communication between the Master
Switching Panel and any of the outstation
speaker bo es in the system.
All calls will be registered on the Master
Switching Panel when the “Call” button is
pressed on any of the Outstations.
To answer a call, the Evacuation
Manager, simply presses the flashing
button for the corresponding outstation. At
this point a voice link will be opened.
Once the conversation has finished, the
pressing of the fully illuminated button, on
the Master Switching Panel, will now
cancel the call.
If for any reason the Evacuation Manager
wishes to speak to an outstation, he
simply presses the button corresponding
button of the outstation. A voice link will
be opened and the button will fully
illuminate.
NB: Acoustic feedback will occur when
the Lift car doors open if the Main
Switching Panel is near the Lift car's
opening. (Use a relay on the "door open"
signal to avoid feedback problems).
NB: Fire Fighting will have priority over
the Evacuation. i.e. if the evacuation
switch and fire fighting switch are turned
ON at the same time, the system will
operate as the Fire Fighting Intercom
system.
Fire Fighting
Interc m
After every 10
utstati ns a
P wer B ster
will be required.
Refer t Page 6.

Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: SEREVA01 Block 13/09/13
Top most landing
Bus 1
Motor Room (This area represents the Motor Room)
ALARM PUSH
N/O C ntacts
V ltage Free
Windcrest
PRESS ALARM
BUTTON F OR
3 SECOND S
IF UNOBTAINA BLE
PRESS AGAIN
Windcr est
Press Butto n for
3 Second s for
HELP, Pre ss again
in Unobt ainable
Press and Hold
for Intercom
with mot or room
Windcr est
Press Butto n for 3 Second s for HELP, Pre ss again in Unobt ainable Press and Hold for Intercom with mot or room
6 way
6 way
Windcrest
AD1000EN-4R
System
Lift Car Lift Pit
T p f Li ft
Car
230 V AC
GSM/Phone Line
Car Speaker
Interface
Example f
Fire Fighting & Evacuati n
System + EN4 System
BT S cket
CT5 Cable
CT5 Cable
CT5 Cable
6 Way LSF
(Blue)
12 Way
Travelling
6M CT5 Cable
EVACUA TION INTERCO M
230
VAC
Evacuati n
Interc m
P wer Supply
EVACUA TION INTERCO M
EVACUA TION INTERCO M
Page 3
EVACUATION
INTERC OM
Lift Controller Contacts
from Euro Switch
FIRE FIGHTING
INTERC OM
Fire Fighting
Interc m
After every 10 utstati ns a
P wer B ster will be required.
Refer t Page 6.

Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: SEREVA01 Block 13/09/13
Top most landing
Lift Shaft (This area represents the Lift Shaft)
ALARM PUSH
N/O C ntacts
V ltage Free
Windcrest
PRESS ALARM
BUTTON F OR
3 SECOND S
IF UNOBTAINA BLE
PRESS AGAIN
Windcr est
Press Butto n for
3 Second s for
HELP, Pre ss again
in Unobt ainable
Press and Hold
for Intercom
with mot or room
Windcr est
Press Butto n for 3 Second s for HELP, Pre ss again in Unobt ainable Press and Hold for Intercom with mot or room
6 way
Windcrest
AD1000EN-4R M RL
System
230 V AC
GSM/Phone Line
Car Speaker
Interface
BT S cket
CT5 Cable
CT5 Cable
CT5 Cable
6 Way LSF
(Blue)
12 Way
Travelling
CT5 Cable
EVACUA TION INTERCO M
230
VAC
Evacuati n
Interc m
P wer Supply
EVACUA TION INTERCO M
EVACUA TION INTERCO M
Windcrest
PRESS AND
HOLD
BUTTO N F OR
INTERC O M
INTERCOM
PRE SS
TO
SPEAK
TOP PITCAR
4 way
6 way
4 way
6 way
CT5 Cable
Page 4
Example f
Fire Fighting & Evacuati n
System + EN4 MRL System
EVACUATION
INTERC OM
Lift Controller Contacts
from Euro Switch
FIRE FIGHTING
INTERC OM
Fire Fighting
Interc m
After every 10 utstati ns a
P wer B ster will be required.
Refer t Page 6.

Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: SEREVA01 Block 03/12/13
CAT5 Cable
Lift Pit
Lift Car
(Everything
here is
placed in the
Lift Car, or in
the COP)
Top of
Lift Car
(Everything
here is
placed on
the top of lift
car)
Landing
(Everything
here is
outside the
lift, but near
the lift door
on the wall)
ALARM PUSH
N/O C ntacts
V ltage Free
Windcr
est
Press Butt on for
3 Seconds for
HELP, Pre ss again
in Unob tainable
Car
Speaker
Interface
Windcrest
AD1000EN-3R
MRL System
Lift No:
For Tec hnical Assistance Tel : [phone]
Back up Battery to be Te sted/Changed A ug
2008
Speaker
PCB
T p f CAR
Speaker
Top of CAR
Alarm Push
Micr ph ne
4 Way
230 V
AC
GSM/
Phone Line
230 VAC
Evacuati n
Interc m
P wer Supply
Travelling
Cable
Windcrest
PRE SS ALA RM
BUT TON FO R
3 SECO ND S
IF UNOB TAIN ABLE
PRE SS AGAIN
3 Way
EVACUA TION INTERCO M
CAT 5 Cable
Patch cable
EVACUA TION INTERCO M
Top most landing
EVACUA TION INTERCO M
Page 5
EVACUATION
INTERC OM
Lift Controller Contacts
from Euro Switch
FIRE FIGHTING
INTERC OM
Fire Fighting
Interc m
Example f
Fire Fighting & Evacuati n
System + EN3 System
After every 10 utstati ns a
P wer B ster will be required.
Refer t Page 6.

To Lift Car
Travelling Cable
Min. 6 way screened & twisted
with min. of 0.75mm
2
conductor
(Travelling Cable will be
required if the system is
StandAlone Evacuation system
or the Windcrest Autodialler
unit is installed on top of the Lift
Car)
CAT5 Cable
EVACUATION INTERCOM
230
VAC
Evacuati n
Interc m
P wer Supply
EVACUATION INTERCOM
EVACUATION INTERCOM
EVACUATION INTERCOM
This area represents
Lift M t r R m r T p f
the Lift Shaft
Lift Shaft
Power
Booster
Power
Booster
Power
Booster
Up t 12 way
cable can be
used s that
the v ltage n
the b tt m
m st landing is
n less than
20V with all
utstati ns
plugged in and
p wered up.
10 outstations
10 outstations
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
10 outstations
10 outstations
Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: SEREVA01 Block 16/11/19
P wer B ster Wiring
Page 6
C nnect P wer B ster
after every 10 utstati ns as
per the drawing. Upt 12
way cable can be used s
that the v ltage n the
b tt m m st landing is n
less than 20V with all
utstati ns plugged in and
p wered up.
Up t 12 way
cable can be
used s that
the v ltage n
the b tt m
m st landing is
n less than
20V with all
utstati ns
plugged in and
p wered up.

++
- - M0B+-
Evacuati n Interc m P wer Supply Unit
Terminals F r
P wer B ster
- 1
- 2
- 3
- 4
- 5
- 6
+ 7
+ 10
+ 11
+ 12
PREVIOUS BRANCHNEXT BRANCH
POWER FROM ABOVEPOWER TO BELOW
POWER BOOSTER
T Next P wer
B ster’s
“POWER TO
ABOVE”
Terminals
FIRST POWER BOOSTER
CAT5 Cable
EVACUATION INTERCOM
230
VAC
Evacuati n
Interc m
P wer Supply
EVACUATION INTERCOM
EVACUATION INTERCOM
EVACUATION INTERCOM
This area represents
Lift M t r R m r T p f
the Lift Shaft
Lift Shaft
Power
Booster
Power
Booster
Power
Booster
12 Way Cable
12 Way Cable
12 Way Cable
10 outstations
10 outstations
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
10 outstations
10 outstations
Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: PSUtoBooster 03/01/2023
PSU t P wer B ster
Wiring
Page 7
+ 8
+ 9
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6

PREVIOUS BRANCHNEXT BRANCH
POWER FROM ABOVEPOWER TO BELOW
POWER BOOSTER
T Next P wer
B ster’s
“POWER TO
ABOVE”
Terminals
SECOND POWER BOOSTER
CAT5 Cable
EVACUATION INTERCOM
230
VAC
Evacuati n
Interc m
P wer Supply
EVACUATION INTERCOM
EVACUATION INTERCOM
EVACUATION INTERCOM
This area represents
Lift M t r R m r T p f
the Lift Shaft
Lift Shaft
Power
Booster
Power
Booster
Power
Booster
12 Way Cable
12 Way Cable
12 Way Cable
10 outstations
10 outstations
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
CAT5 Cable
10 outstations
10 outstations
Tel: [phone]
Fax: [phone]
Windcrest
(UK) Ltd
Drawing: Booster-Booster 03/01/2023
P wer B ster t
P wer B ster Wiring
Page 8
PREVIOUS BRANCHNEXT BRANCH
POWER FROM ABOVEPOWER TO BELOW
POWER BOOSTER
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6
+ 7
+ 8
+ 9
+
10
+
11
+
12
- 1
- 2
- 3
- 4
- 5
- 6

Speaker Bo
Windcrest
(UK) Ltd
Tel: [phone]
Fax: [phone]
RJ45 Plugs Wiring
Drawing: SEREVA Landings
03/09/10
6 Way
nth Floor
Landing
nth Floor
Landing
Page 9
Speaker Bo
31 52 4 6 7 8
1. Orange/White……….A (Data)
2. Orange……………….B (Data)
3. Green/White ………..+24V
4. Blue…………………..Audio
5. Blue/White…………...Audio
6. Green………………...Ground
7. Brown/White…………+24V
8. Brown………………...Ground
WRONG
-
+
BT
BT A
B
LED
RJ45 to Terminal
25-30V
DC
25-30V DC, when
all speakers are
OFF.
Data – Ma imum
voltage 5Vpp
For Troubleshooting, connect the RJ45 to Terminal to
the Cable and check the above readings. If the readings
are different than above, please contact Windcrest.

Windcrest
(UK) Ltd
Tel: [phone]
Fax: [phone]
RJ 45 Bus Terminator
&
RJ45 to Terminal
Drawing: SEREVA Landings
03/09/10
Page 10
Cable from the
other landing
Bus
terminator
Top Most Landing
Connect bus terminator
to the last outstation on
each bus.
A = White
B = Green
+ = Pink
GND = Gray
BT (Audio)= Blue
BT (Audio) = Yellow
-
+
BT
BT A
B
LED
RJ45 to Terminal
25-30V
DC
25-30V DC, when
all speakers are
OFF.
Data – Ma imum
voltage 5Vpp
For Troubleshooting, connect the RJ45 to Terminal to
the Cable and check the above readings. If the readings
are different than above, please contact Windcrest.

Evacuation Functions
Interc nnecti n
Connect the main Evacuation Panel to the Control Bo . Connect all the Landing Speakers to the
bus. Lift Controller Contacts are provided on the Main Panel.
Lift C ntr ller Spare C ntacts:-
Blue or Orange - Common
Green or White- Normally Open
Yellow- Normally Closed
Operati n
To activate the evacuation system, place the EURO switch in the ON position. All the LEDs for the
Landing Speakers and the Lift Car will flash for 5 seconds when the system is analysing the
Outstations. After 5 seconds, the LEDs on the main Panel will be ON for the outstations which are
present working (i.e. Data Link is Working) for 3 seconds. The “Listen” Pictogram will be ON to
indicate that the system is ready.
At the all Landing Speakers Call Button will Flash slowly to Indicate System is ON.
On pressing the CALL button on any outstation, the LED will start flashing faster to indicate
placement of a call. At the same time the corresponding LED for that outstation and a buzzer will
operate. The flashing and buzzing will continue till the person on the Main Control Panel answers the
call by pressing the corresponding button. At the point the voice link is opened, the LED on the
calling outstation and main panel will remain ON till the voice link is terminated.
When Voice Link is active, press to speak button will control the speech from the master station.
When press to speak button is released, Main Control Panel’s microphone will be muted and
outstation microphone will be ON, and Main Control Panel’s microphone is muted. When press to
speak button is pressed and Hold, Outstation microphone will be muted and Master Panel
microphone will be ON. Pictograms at the Main Control Panel and the Landing Speaker will show the
status of speak/listen. i.e. when the speaker bo ’s Mic will be ON, “Speak” Pictogram will illuminate
and when the Speaker Bo ’s Mic will be OFF, “Listen” Pictogram will illuminate.
A call can be made to any of the Outstation by simply pressing the button for that outstation on the
Main Control Panel. As soon as the button is pressed the LED on both the outstation and the Master
Panel will be steady ON and a two way communication is possible via press to speak button on the
Main Control Panel.
The call can be terminated by the pressing the same button again at which point LEDs on the
outstation and Main Control Panel will go off and the Pictograms at the Landing Speakers will be
switched off and at the Main Panel “Listen” Pictogram will illuminate to indicate the system status.
When Evacuation Switch is turned OFF, Both the Pictograms at the Main Control Panel will be
switched off and Push Button LED at all the Landing Speakers will be turned OFF.
The buzzer will sound when the Low Battery is detected.
Note:- On powering up the system (i.e. Mains/Battery Connected), all the buttons including Speak
and Listen Pictograms will flash for 10 seconds. Landing Buttons will flash for 2 seconds.
Windcrest
LiftBits Ltd
Tel: [phone]
Fax: [phone]
Evacuati n System Operati n
Drawing : Evac Functi ns Page: 11

Fire Fighting Function
Interc nnecti n
Connect all the Landing Speakers and the Motor Room speaker to the bus. Lift Controller Contacts
are provided on the Main Panel.
Lift C ntr ller Spare C ntacts n the Fire Fighting Switch:-
Orange - Common
White- Normally Open
Yellow- Normally Closed
Operati n
To activate the Fire Fighting system, place the EURO switch in the ON position. Push buttons on all
the Landing Speakers and the Lift Car Speaker will switch off and disabled. The three way
communication link will be ON, between the Fire-Evacuation Panel, Motor Room and the Lift Car.
To indicate the Fire Fighting Intercom is ON, both Speak & Listen Pictograms will be turned ON, on
the Lift Car Speaker, Fire Fighting Pictogram will be turned ON, on the Motor Room Speaker and
Listen Pictogram will be turned ON, on the Fire-Evacuation Panel.
“Press to speak” button is to be used to speak from Fire-Evacuation Panel & the Motor Room Panel.
All the other buttons apart from “Press to Speak” will be disabled on the Fire-Evacuation Panel.
Note:- The Fire Fighting Intercom will have priority over the Evacuation Intercom.
Windcrest
LiftBits Ltd
Tel: [phone]
Fax: [phone]
Fire Fighting System Operati n
Drawing : FF Functi ns Page: 12

Dip Switch Arrangement
Drawing : Dip Switch Page: 13
Windcrest
LiftBits Ltd
Tel: [phone]
Fax: [phone]
All speakers have unique address. This address is set by the Dip Switch on the back of the each
speaker bo . Following are the arrangements for the Dip Switch for the different speaker bo .
Note: X – Do Not Care
123456
Car Speaker OFF OFF OFF OFF OFF OFF
Motor Room Fire Fighting Speaker
XXXXXX
Master Panel :- This address will define the number of outstations (E cluding Lift Car (Default)). i.e.
If the system has 21 outstations + Lift Car then following is the set up.
Master Panel ON OFF ON OFF ON X
Master Panel is addressed from the factory.
Evacuation Landing Speaker 1 2 3 4 5 6
Landing 1(Bottom Most) ON Off Off Off Off X
Landing 2 Off ON Off Off Off X
Landing 3 ON ON Off Off Off X
Landing 4 Off Off ON Off Off X
Landing 5 ON Off ON Off Off X
Landing 6 Off ON ON Off Off X
Landing 7 ON ON ON Off Off X
Landing 8 Off Off Off ON Off X
Landing 9 ON Off Off ON Off X
Landing 10 Off ON Off ON Off X
Landing 11 ON ON Off ON Off X
Landing 12 Off Off ON ON Off X
Landing 13 ON Off ON ON Off X
Landing 14 Off ON ON ON Off X
Landing 15 ON ON ON ON Off X
Landing 16 Off Off Off Off ON X
Landing 17 ON Off Off Off ON X
Landing 18 Off ON Off Off ON X
Landing 19 ON ON Off Off ON X
Landing 20 Off Off ON Off ON X
Landing 21 ON Off ON Off ON X
Landing 22 Off ON ON Off ON X
Landing 23 ON ON ON Off ON X
Landing 24 Off Off Off ON ON X
Landing 25 ON Off Off ON ON X
Landing 26 Off ON Off ON ON X
Landing 27 ON ON Off ON ON X
Landing 28 Off Off ON ON ON X
Landing 29 ON Off ON ON ON X
Landing 30 Off ON ON ON ON X
Landing 31 ON ON ON ON ON X

Windcrest
(UK) Ltd
Tel: [phone]
Fax: [phone]
Serial Car Speaker
Interface with Windcrest
Autodialler
Drawing: SER CAR + Autodialler
03/09/10
Page 14
Cable from the
Last Landing
Red (Autodialler ‘+’)
Black (Not Used)
Green (Autodialler ‘G’)
Yellow (Autodialler ‘Y’)
For EN1/EN3
Application refer to
the Page 16.
For EN4
Application Refer to
the Page 17.
Bus
terminator
Serial Data C ntr ller
Aut dialler Car Speaker B x
NB: Ign re this drawing f r the StandAl ne Evacuati n Installati n. This drawing is applicable
ONLY f r AD1000 Range f Aut diallers which is c nnected t a Serial Evacuati n System.
White Cable for
Pictogram/Loop/Amplifier
Lift Car
Alarm Push
in the Lift
COP
Green (3)
Red (2)
White (5)
Blue (4)
Green (3)
Red (2)
White (5)
Blue (4)
To Autodialler ‘+’
To Autodialler ‘A’
Serial Evacuati n-AD1000EN-xR
Interface f r the Car Speaker &
Lift Car Alarm Push
To Autodialler ‘PF’
To Autodialler ‘G’
N te:- If the Aut dialler is
already wired, please
refer t the Page 12.

Windcrest
(UK) Ltd
Tel: [phone]
Fax: [phone]
Serial Car Speaker
Interface with E isting
Windcrest Autodialler
Drawing: SER CAR + Autodialler
03/09/10
Page 15
Cable from the
Last Landing
Red (Autodialler ‘+’)
Black (Not Used)
Green (Autodialler ‘G’)
Yellow
(Autodialler ‘Y’)
For EN1/EN3
Application refer to
the Page 16.
For EN4
Application Refer to
the Page 17.
Bus
terminator
Serial Data C ntr ller
Aut dialler Car Speaker B x
NB: Ign re this drawing f r the StandAl ne Evacuati n Installati n. This drawing is applicable
ONLY f r AD1000 Range f Aut diallers which is c nnected t a Serial Evacuati n System.
White Cable for
Pictogram/Loop/
Amplifier
Green (3)
Red (2)
White (5)
Blue (4)
Green (3)
Red (2)
White (5)
Blue (4)
To Autodialler ‘+’
To Autodialler ‘A’
Serial Evacuati n-AD1000EN-xR
Interface f r the Car Speaker &
Lift Car Alarm Push
To Autodialler ‘PF’
To Autodialler ‘G’
Disconnect the wire connected to
the E isting Autodialler Terminal “A”
and connect to this terminal
Disconnect the wire connected to
the E isting Autodialler “+” and
connect to this terminal

Windcrest
Tel: [phone]
Fax: [phone]
Page 16 24/06/12
AD1000 EN 1 & Serial Controller
+
A MT
C+P
T
s
-AC
-+
BATT
Lamp
Eng
GSer
NO BT PFY
LINE PUSH
2 Way
Trailing
Cables
Screened
and Twisted
if Possible
If the Main unit is Mounted on the Lift car, e tend only the Phone line coming in, using Terminal blocks (Red & White wires) or a BT Socket Terminals 2 & 5
IMPORTANT: Backup Battery MUST be connected the correct way around. If not, the PCB tracked Fuse will blow.
Use the Voltage Free Contacts (Ma Load 500 mAmp 24V) to switch ON/OFF the Lamp/LED in the ALARM push. PF & Y Make when ALARM Activated PF & G Make when ALARM Acknowledge (By Called Person pressing a Star ( ) on his phone.)
NB: If the main Unit is m unted in the M t r/Pump r m, 9 way Trailing cable will be required. If the Main unit is m unted n the Lift car, 2 way trailing cable will be required.
Teleph ne Cable
t Exchange r
PABX if in an
Office Building
Use Terminals
A & B r 2 & 5
ONLY
15 way D Socket
for the Programmer
{
Push Button to Hold Down when Recording Lift Location
*
Serial Evacuati n-AD1000EN-xR
Interface f r the Car Speaker & Lift
Car Alarm Push
Serial Data C ntr ller

Windcrest
Tel: [phone]
Fax: [phone]
CAR/D CAR/S PIT/D PIT/S TOP/D TOP/S MR/SC P T p t
- -
+ +
IMPORTANT:
Backup Battery MUST be
connected the correct way around.
If not, the PCB tracked Fuse will blow.
C nnect the lead with the BT Plug int
the ph ne s cket f the Building's
ph ne system. (The ph ne line Must
be n 2 wires anal gue system)
15 way D Socket
for the Programmer
5V ok LED
2
5
4
3
Speech
Synthesis
Prompts
Blue Green
Red
White
All other unconnected
terminals shown, may
be pre-wired
All cable used in the
installation should
be Screened and
Twisted to minimise
Electrical Noise
"System Ready"
+
A MT
C+P
T
s
-AC
-+
BATT
Lamp
Eng
G
NO BT PFY
LINE PUSH
Ser
Serial Evacuati n-AD1000EN-xR
Interface f r the Car Speaker & Lift
Car Alarm Push
Serial Data C ntr ller
AD1000 EN4 and Serial Data Controller
Page 17 Date: 12/07/12

++
- - M0B+-
12V Output
Low Battery Relay Output
(“0” - Common, “B” - Normally Open)
Low Battery = Closed
Battery Good = Open
Mains Detection Relay Output
(“0” - Common, “M” - Normally Open)
Mains Failure = Closed
Mains Good = Open
Windcrest
(UK) Ltd
Tel: [phone]
Fax: [phone]
Low Battery & Mains
Detection Output
Drawing: Mains & Batt
Page 18