Winegard DS2000S User manual

c
lag holes
(5/16"x 3" lag screw
recommended)
stud
If siding is heavy enough, the
outer holes can also be used
to help secure the base.
a
b
Universal Mount w Adapter Plate DS2000S Quick Start Guide
INSTALLATION
Printed in U.S.A. © 2022 Winegard Company Rev 9-22 2452507
Starlink is a trademark of Space Exploration Technologies Corp. All trademarks, registered trademarks and logos
are the property of their respective owners and are not aliated with Winegard Company.
1LOCATE a stud in the area to be
installed.
2DRILL a small pilot hole to help start
threading the lag bolts (5/16"x 3"
recommended) (a).
3APPLY silicone sealant to the back of
the base to seal holes (b).
4USE the lag bolts to tighten the base to
the wall. Make sure the mast is plumb.
5INSERT the U-bolts through the slots
in the adapter plate and secure loosely
with the nuts (c).
6POSITION the adapter plate facing
UP, and place the bottom U-bolt over
the antenna mount pipe (c). Tighten
the two bottom U-bolt nuts.
7SLIDE the auxiliary pipe through the
upper U-bolt and into the antenna mount
pipe as far as possible (d). The second
guide rests on the top edge of the pipe
mount. Tighten the nuts on the upper
U-bolt until the pole is secure. Verify the
bottom U-bolt is also secure.
WARNING: INSTALLATION OF THIS PRODUCT
NEAR POWER LINES IS DANGEROUS. For
your safety, follow the installation instructions.
See back for grounding instructions
1.0"– 1.5"
auxiliary
pipe dia.
or Starlink
CONTENTS:
2 - U-bolts
1 - Adapter plate
4 - Flanged hex nuts
1 - Pipe & foot assembly
d
Not provided: 7/16"wrench, lag bolts
SCAN FOR
WARRANTY
OR CALL
800-288-8094
Winegard Company 2736 Mt. Pleasant St. |Burlington, IA 52601
MORE
PRODUCT
INFORMATION

HOW TO PROVIDE LIGHTNING PROTECTION
FOR TV ANTENNA AND SET
STEP 1. Mount the lightning arrestor as close as possible
to where the downlead enters the house.
STEP 2. The ground wires for both the mast and the
downlead should be copper or aluminum wire,
number eight (8) or larger.
STEP 3. The downlead wire from the antenna to the
lightning arrestor should be secured every
four (4) to six (6) feet to prevent whipping.
NOTE: In the case of a "ground up" antenna installation,
it may not be necessary to ground the mast if the
mast extends four or more feet into the ground.
Consult a TV serviceman for proper depth in your
location.
HOW TO PROVIDE LIGHTNING
PROTECTION
FOR TV ANTENNA AND SET
STEP 1. Mount the lightning arrestor as close
as possible to where the downlead enters the
house.
STEP 2. The ground wires for both the mast
and the downlead should be copper or
aluminum wire, number eight (8) or larger.
STEP 3. The downlead wire from the antenna
to the lightning arrestor should be secured
every four (4) to six (6) feet to prevent
whipping.
NOTE: In the case of a "ground up" antenna
installation, it may not be necessary to ground
the mast if the mast extends four or more feet
into the ground. Consult a TV serviceman for
proper depth in your location.
1450071
Antenna Lead
In Wire
Ground
Clamp
Electric
Service
Equipment
Antenna
Discharge Unit
(NEC Section 810-20)
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
Ground
Clamps
Grounding Conductors
(NEC Section 810-21)
NEC - National Electrical Code
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70
Antenna
Lead-in Wire
Ground
Clamp
Ground
Clamp
Electric
Service
Equipment
Grounding Conductors
(NEC Section 810-21)
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
Antenna Discharge Unit
(NEC Section 810-20)
NEC - National Electrical Code
Example of antenna grounding as per
National Electrical Code, ANSI/NFPA 70