WinnWell PRO FORM User manual

PRO FORM REGULATION HOCKEY NET
WITH QUIKNET MESH SYSTEM AND BACKSTOP
Please ensure all part numbers are
accounted for prior to installation
Missing Parts, Required
Replacements, or Inquiries
with Assembly
Please Contact
ASSEMBLY INSTRUCTIONS
-Page 1-
STOP

1. Remove all parts from packaging and carefully remove pipe plugs
without damaging the pipe openings.
2. Begin by gathering parts (A)-(M).
3. Ensure you have enough room to begin the assembly (10 ft x 5 ft)
4. Begin the assembly from the base and work your way to the top.
5. Refer to diagram for instruction
(*Note: Connections may t snug so if necessary use a rubber mallet)
Instructions to Build:
4’x 6’ Steel Hockey Goal
-Page 2-
Attaching the QuikNet Mesh
PART NO. SKETCH QTY
N1
1. Gather part (N)
2. Begin fastening the netting to the goal using the Velcro straps
at the top of the goal and continue all the way around the net.
(Refer to diagram below for Velcro procedure)
(i) Open Velcro tab (ii) Slip tab through
“Roadez” wire weld
(iii) Close Velcro tab
*Note: The QuikNet mesh has 3
coloured tabs. The two red tabs
line up with the front post at parts
(E) and (F) and the green tabs sits
at the midpoint of part (D)
PART NO. SKETCH QTY
A
C
B
D
E
F
G
H
J
K
I
1
1
2
1
1
1
1
1
1
1
1
1
1
E L F
BA
D
K
C C
G H
J
I
M
Red Tab
lines up here
Red Tab
lines up here
Green Tab
lines up here
L
M

Instructions to Build:
The Backstop (Sides)
PART NO. SKETCH QTY
2
2
4
1
1
1
1
4
4
2
8
8
1
1
2
3
36
7
1
2 828
3
3
4
5
1
3
4
5
6
7
8
1. Begin by gathering parts (1)-(8).
2. Refer to the diagram above for assembly
(Note: Connections may t snugly so if necessary use a rubber mallet)
3. Once the two frames have been assembled, you can attach the netting
4. Begin by fastening the 4 corners of the netting to the 4 corners of the
frame using the zip ties provided (see Figure 1)
5. You will need 2 of the 14’ strings to
fasten the netting to one side frame.
6. Begin by tying o one end of the
14’ string to the frame.
7. Figure 2 illustrates how the netting
should then be wrapped:
(i) Corners - lace every square box
(ii) Sides - lace every other square box
(iii) Bottom - lace every square box to
opposing wire weld
8. Once the entire net is fastened
ensure the strings are tied o tightly
with good knots.
9. With both side panels completed you
can now fasten them to the goal.
10. Using the pre-drilled holes line up
the side panels to the goal and fasten
using the bolts and buttery nuts provided
(Refer to diagram above).
-Page 3-
9
10
11
12
14
13
14’
1’
Figure 1 Figure 2

Instructions to Build:
The Backstop (Top) & Pocket Target
PART NO. SKETCH QTY
1
1
10
1. Begin by gathering part (15).
2. Ensure that the thick strap on the netting is at the top when
you begin assembly.
3. Secure the top straps of the netting to the wire weld on the inside
corner of the frames using the white 1’string provided.
4. Next you can secure the bottom corners of the top net to the steel
loops on the side panels using the 1’ string provided.
5. Now you need to secure the sides of the netting to the panels.
6. Use the 14’ strings provided to lace the netting to the side panels and
goal. (See gure below)
-Page 4-
Attaching the Pocket Target
1. Begin by gathering part (16) - (17)
2. Start by fastening the top corner of the target to goal using the
Velcro straps provided
Note: 3 Velcro straps are used for the top corners and 2 are used
for each of the bottom two locations.
(Refer to the diagram to the left for placement instruction).
15
16
17 NOTE: 2 of the 14’ Strings are
required to fasten the top net
to the goal and side stops
(See diagram to left)
14’ String
Velcro Strap