Winsome house WHSL445 User manual

Page: 1
Instruction, Use & Care Manual
Please save this manual for future reference.
Thank you for purchasing this Winsome House product. This product has been manufactured with the highest standards
of safety and quality.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Operating Instructions
BEFORE USING THIS PRODUCT: READ, UNDERSTAND AND FOLLOW THESE INSTRUCTIONS.
How Your Solar Motion Sensor Light Works:
During the day, the solar charge panel included with this LED Solar Motion Sensor Flood Light converts sunlight into
electricity recharging the batteries. Using this stored energy, the LED light turns on automatically at night when motion is
detected.
The light works with a built-in PIR (Passive InfraRed) sensing device which is continuously scanning for heat-source moving
in its detection scope. Once a heat source (such as a human or a car) is detected in that area, the light switches on
immediately and automatically to illuminate your pathways, steps, patios, porches, or anywhere you select for safety,
convenience, and security. The light remains on while the moving heat source stays in the detecting scope.
 Motion-activated light
 Duration and sensor time adjustable
Choosing a Location for Your Solar Motion Light:
 The solar light must be located in a position where it can get direct sunlight on the solar panel, and generally free
from cover and shade. When locating a suitable position for the unit, remember that it detects an area of about 45-60
degrees vertically and about 180 degrees horizontally, with a range of over 5 meters (16.4 ft). See figure above.
 Make sure that the photo sensor on the lamp body is not going to be affected by another light source, otherwise the
light will not illuminate at dusk.
 The solar light must be left to charge for two sunny days before first time use so that the best results are achieved.

Page: 2
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Operation:
 Connect the solar panel to lamp with about 5 meters (16.4 ft.) wires by insert plug into the lamp “INPUT” socket at
the lamp bottom (see figure below). Turn the switch to the “AUTO” position. It will automatically charge during the
daytime and work during the night.
 Adjust the “SENSOR LEVEL” switch at the bottom of the lamp body to change the working time to earlier or later in
the night.
 Adjust the “DURATION” switch at the bottom of the lamp body to change the lamp operating period after detection.
 Turn the switch to the “ON” position, the lamp will be constantly lit starting at dusk, and the motion sensor does not
work.
 Turn the switch to the “OFF position, the lamp will remain unlit, and the motion sensor will not work.
 The performance of the solar lamp will vary with the time of the year. It will deliver light longer when it has had a full
day in the sun rather than a day in overcast weather.

Page: 3
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Installation Tips
There are two ways to assemble the solar panel: Post Mounted, Wall/Deck Mounted
 Carefully remove the Solar Lamp and all the fittings out of the box.
Post Mounted
 Setting the “L” shape screw (1) to solar panel (8) with PA3*15 Screw (4). See Figure 1.

Page: 4
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
 Connect “L” shape screw and bracket for solar panel (6) and “U” shape screw (5). See Figure 2.
 Tumble in the “L” shape screw to the pillar and twist the “U” shape screw tightly. See Figure 3.
Wall or Deck Mounted
 Choose the wall or deck which you want to mount the solar panel. There are four holes for the bracket of the solar
panel, burrowed with inflatable capsules (7). See Figure 4.

Page: 5
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
 Fit the bracket with the solar panel with the provided PA3*15 screw. See Figure 5.
 Set the bracket on the wall or deck with four PA4*35 screws (9). See Figure 6.
 Adjust the angle of solar panel to make sure it can get more light. See Figure 7.

Page: 6
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Lamp Installation
 Take off the wall bracket for the lamp body from the lamp body. See Figure 8.
 Choose the wall you want to set and signed with the three holes of housing. See Figure 9.
 Burrowed with the inflatable screws on the three holes. See Figure 10.
 Fix the wall bracket with three PA4*35 screws. See Figure 11.
 Set the lamp body to the wall bracket. See Figure 12.
 Adjust the angle of the lamp sensor (see Figure 13), and adjust the “SENSOR LEVEL” and “DURATION” (see Figure 14)
according to your preference.

Page: 7
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Lamp head is adjustable as show below, but do not over rotate:
Replacing the Batteries
For best results, batteries should be replaced every 12 months.
 Detach the housing from the lamp body by pushing it downward.
 Take off the four screws with a screwdriver, and replace the old batteries. Make sure the new batteries are
rechargeable batteries.
 Install the new batteries in the battery compartment, ensuring the correct polarity is observed.
 Reassemble the unit by reversing the above procedure.
Maintenance
To keep your solar motion sensor light looking new, keep the lens free of dust and deposits by wiping occasionally with a
dry cloth or with warm soapy water if necessary.
Most important, ensure that the solar panel is kept free of dirt and debris at all times. A dirty solar panel will not allow the
batteries to fully charge, and this will shorten the life of the batteries and may cause the light to not function properly.
Technical Specifications
LED Light Setting: 100-120 Lumen (High)
5 Lumen (Low)
Rechargeable Battery Type: soft package 1500mAh 3.6v NI-MH
Solar Panel: Amorphous silicon
High Light activation (range): 30 seconds
Charge Time (minimum): 6 Hours
Motion Sensor Range: 5 – 8 meters (16.4 – 26.25 feet); 180 degrees Horizontal

Page: 8
Instruction, Use & Care Manual
Please save this manual for future reference.
Product Name:
LED Solar Motion Sensor Flood Light
SKU #:
WHSL445
Troubleshooting:
Light will not switch
on when there is
movement in the
detection area
 Ensure that the power switch on the main body has been turned to the AUTO or ON position.
 Ensure that the motion sensor has been positioned to face oncoming movement.
 Ensure that the battery has been fully charged in direct sunlight for one sunny day.
 Check to see that the solar cell charge panel is facing south so that it receives direct sunlight for
most of the day, enabling the battery to fully charge.
 Check to see that the solar panel is not near the night time light sources, such as street lights.
Light switches on
during the day
 Ensure the flood light is not placed in shady area.
 Ensure the solar panel is facing towards direct sunlight.
Light switches on for
no apparent reason
 Moving trees, traffic, pet, or birds may be getting in the area of detection. This may be unavoidable;
however, the sensor could be redirected to a height where this less likely to occur.
 If there are reflective objects in the detection area, such as windows, water, or white walls, you may
need to redirect or possibly reposition the motion sensor.
 Test the motion sensor by covering it completely with cardboard, and waiting several minutes to
make sure it does not detect motion.
Light quickly flashes
on and off
 Battery charge may be low. Turn the power switch to the OFF position and charge the battery for
two (2) sunny days, ensuring the solar cell charge panel has been placed in direct sunlight.
Light is not as bright as
normal
Battery charge may be low. Turn the power switch to the OFF position and charge the battery for two (2)
sunny days, ensuring the solar cell charge panel has been placed in direct sunlight.