Winson WNI-6712 User manual
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
1/29
Winson wireless barcode scanner user manual
Launch date：2019-5-29
1、Ver：V3.8
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
2/29
Revision record
2019/5/29 Rev 3.8
1. Remove the settings that do not match the code.
2. The version specification is revised based on Src-0085 V3.4 and Src-0083 V3.4.
2018/11/30
1. Classification character output setting code
2017/8/9 Rev 3.3
1. Add wireless channel setting code
20017/9/14 rev 3.4
1. Modify the input and output character format setting code
20170915 Rev 3.5
1. Increase keyboard case detection settings
2. Increase the small keyboard switch settings
20170125 Rev3.6
1. Increase proximity matching
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
3/29
1 . Comprehensive settings
1.1 Setting instruction description
1. The setting bar code is uniformly printed with Code128 type CODE B set bar code.
2. An asterisk (*) in the description part indicates the factory default parameters.（1）Scan: Enter setting
mode “@SET”. After enter setting, it will exit the setting mode if next setting command is not scan
within 20s.
（2）Scan: the relevant setting barcode. In this step, you can scan one or more setting barcode
commands.
（3）Scan: Exit and save “@END”.
（4）The setting of some functions can directly scan the corresponding quick setting bar code. Such as:
pairing barcode, unpairing barcode, etc.
3.2 Set command data format
Table 3.3-1 Setting command data format table①
Prefix
Setting goals
Type
Parameter
WN-
T-/R-/W-
Refer to "Set Barcode Type
Table"
*****
Notice ①This format does not include instructions for entering settings and saving and exiting settings.
Table 3.3-2 Set instruction data format analysis
Format
Data
Description
Prefix
WN-
Fix prefix symbol
Setting goals
T-/R-/W-
T-:Means to set the barcode directly to the sender end.
R-:Means to set the barcode directly to the receiver end,
and the setting bar code of the receiving end
needs to be forwarded by the sending end
through wireless transmission.
W-:The sender end and receiver end work at the same
time
Type
Refer to "Set Barcode Type Table"
Parameter
The parameter is 4 characters in the range of "0~9"
3.4 Set barcode type table
Table 3.4-1 Set barcode type table
Type
Description
A
Wireless pairing/unpairing
B
Multi-language settings
C
View firmware information/Modify frequency
D
Infrared sensor trigger switch
F
Real-time mode / inventory mode / inventory mode data operation
G
Sleep time
H
Restore default setting
I
Data transmission form, start symbol mode setting, custom start
symbol
K
Sending/receiving end firmware upgrade command
L
USB wired output switch
3.5 “Enter setting” and “Save and exit”
Command：
Function
Command
barcode
Remark
Enter setting
@SET
Enter the setting prompt sound,
effective time of 20 seconds
Save and
exit
@END
Save and exit settings prompt sound
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
4/29
Note☆: 1. For the setting of non-quick setting commands, it must first scan to enter the setting command,
then scan the corresponding parameter setting command, and finally scan to save and exit the
setting command.
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
5/29
4. Setting barcode type
4.1 Pairing command★
Function
Command
barcode
Remark
Start
pairing
@.WN-T-A0001/
Can be paired
remotely
Close
pairing
@.WN-T-A0002/
Only allow pairing
Note☆: 1. The effective time of pairing is within 20S from the moment the receiver is powered on (the
LED is flashing). After 20s, the LED is always on and cannot be paired. (This method is for
the receiver without buttons)
2. Press the receiver button, the receiver will automatically enter the pairing state, during this
period it can be paired normally. (This method is for the receiver with buttons).
3. 2.4G stops flashing after pairing successfully.
4.2 HID-KEYBOARD multi langue setting★
Function
Command
barcode
Remark
@SET
*USA
WN-W-B1000
FRENCH
WN-W-B1001
GEMRAN
WN-W-B1002
TUKISH
WN-W-B1003
BELGIUM
WN-W-B1004
BRAZIL
WN-W-B1005
CRZCH
WN-W-B1006
SPANISH
WN-W-B1007
Latin America
@END
Note★: This setting code is valid for both the receiving end (Tx) and the sending end (Rx). If
multiple languages are set when the wireless transmission connection is disconnected, the sending
end language setting will be successful, but the receiving end language will not change.
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
6/29
4.4 Check parameter
Function
Command
barcode
Remark
Output parameter of
system
WN-W-
C1000
1> Firmware version
2> Battery level
3> Wireless channel
Explanation ☆: The command to view the parameters is sent to the receiver along with the system
parameters, and each parameter is separated by a terminator, such as:
PKT{protocol field|WN-W-B1001|parameter 1+0x0D|parameter 2+0x0D |……} (the content of the data
packet in {})
4.5 Operation mode★
Function
Command
barcode
Remark
*Real-time
mode
@.WN-T-
F0000/
Scan and transfer, fail alarm
Cache
mode
@.WN-T-
F1000/
On the basis of real-time mode,
increase the buffer data after
transmission failure. The system
will automatically upload the
cached data after detecting that the
device has not been operated for
three seconds. If the cached data is
not uploaded when the machine is
turned off, the system will continue
to detect the upload after the next
startup until the transmission is
completed.
Inventory
mode
@.WN-T-
F2000/
The barcode data is automatically
stored, and it is uploaded once after
scanning "Upload Data"; scanning
"Clear Data" to clear the data in the
memory "Scan "Data Total" to
view the total number of data in the
memory
After scanning the barcode, the
data is directly stored in the
barcode scanner, and the data will
not be deleted until the [Clear
Data] is scanned. During this
period, you can scan [upload data]
to send the data to the receiver or
directly upload to the PC
Upload data
@.WN-T-
F2001/
Upload barcode data
Data sum
@.WN-T-
F2002/
Upload the sum of barcode
Clear data
@.WN-T-
F2003/
Clear the barcode data in the
inventory mode
Notice☆:1. Six command in operation mode are all quick setting command, the setting is successful
when scan them successful.
2. Upload data, data amount, clear data in inventory mode, these three operation setting
command is unavailable when enter setting mode, if it is already in setting mode, must save
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
7/29
and setting before using these three operation setting command.
3. New 433 and 2.4G solution (model number：WNI-xxx2, WNI-xxx3,WNC-xxx2,WNC-xxx3)
storage data description:
Inventory mode: storage length is 30 Byte data will be able to store 49,000pcs
storage length is 13Byte data will be able to store 104,500pcs
Cache mode:storage length is 30 Byte data will be able to store 14,200pcs
storage length is 13Byte data will be able to store 30,300pcs
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
8/29
4.6 Character input/output/keyboard format setting
4.6.1 Case control and keypad switch
Function
Command
barcode
Description
*Uppercase key
(CapsLK) detect
on
@.WN-W-
F3201/
Turn on uppercase detection,
keyboard Caps will not affect the
output
example: barcode
content:123ABCdef
Turn on Caps output:
123ABCdef
Turn off Caps output:123ABCdef
Uppercase
key(CapsLK)
detect off
@.WN-W-
F3202/
After turn off the caps detection,
the keyboard Caps lock will
affect the output
example: barcode
content :123ABCdef
Turn on Caps output:123abcDEF
Turn off Caps output:123ABCdef
Turn on Numeric
keyboard
@.WN-W-
F3203/
After turn on, it need to set the
output to GBK format. If the
language is German at this time,
it needs to be set to English, and
other languages do not need to be
set.
4.6.2 Out put format and function key setting
Function
Command
barcode
Test instruction
*GBK
output
@.WN-W-
F3001/
1.Support txt and Excel output
2.Use WDI2000 module, set to
GBK output
3.Open txt or Excel, scan the code
to transmit data normally
Unicode
output
@.WN-W-
F3002/
1.Support Word output;
2.Use WDI2000 module, set to
UTF-8 output
Function
key
output
@.WN-W-
F3005/
1.Support testing in Excel file;
2.Add function key suffix:
For example: set the "→"
function key as a suffix, after
outputting data in Excel, the
cursor will point to the right cell
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
9/29
4.7 Sleep times setting★
Function
Command
barcode
Remark
@SET
1 min
WN-T-G0001
*5min
WN-T-G0005
15min
WN-T-G0015
45min
WN-T-G0045
non-sleep
WN-T-G0000
@END
Instructions☆: The calculation method of sleep time：60 * x = n (s) , X is two decimal values after the
barcode
4.8 Restore the factory settings★
Function
Command
barcode
Remark
@SET
Factory
Default setting
WN-W-H0000
1> autoSetFactory
remains unchanged
2> The current
spectrum constant
3> Matching the
address remains the
same
4> The wireless channel
is constant
5> Locking band logo
remains the same
6> Data output way
remains the same
7> The keyboard
language remains the
same
8> Buzzer sound
remains the same
@END
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
10 /29
4.9 0x0A filter
Turning on will filter out the 0x0A (newline character) in the middle of the string, and the 0x0A at the end of the
string (the first and second to last) will not be filtered.
Function
Command
barcode
Remark
*Turn on 0x0A
filter
@.WN-W-
F3301/
After turn on, the
newline character
0x0A in the middle
of the string will be
filtered.
Turn off 0x0A
filter
@.WN-W-
F3302/
If there is a newline
character in the data
after closing, it will
be output normally
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
11 /29
4.12Out put way (USB/USB VCP) ★
Function
Command
barcode
Remark
Start setting
@SET
Enter setting mode
*USB output
WN-W-
L1000
USB interface
VCP output
WN-W-
L1001
USB virtual serial port need
to install the serial port
(USB) driver can be normal
use
RS232 output
WN-R-L1002
1.a serial port output
function only in support of
a serial port output devices
(hardware) can use, now
only RF433 receive support
serial output
2. optimizes the
transmission way of new
products. USB and RS232
serial port transmission can
automatically identify, do
not need to set up a serial
port output
End setting
@END
Save and exit setting
Notice★：
1. The default for USB and RS232 serial Port output, the system will automatically choose the USB or
RS232 serial Port output according to the hardware, without setting
2. When switching USB and Virtual serial Port (Virtual COM Port) need to scan settings to change, but it
don't need to plug the receiver.
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
12 /29
4．14 Auto trigger
Function
Command
Barcode
Remark
@SET
Enable auto trigger
WN-T-D0000
Enable infrared
induction trigger
Disable auto trigger
WN-T-D0001
Disable infrared
induction trigger
@END
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
13 /29
4.9 The command of firmware upgrade
Function
Command
Barcode
Remark
@SET
Receiver
upgrade
WN-R-K0000
1. Receive PC via USB way
connection, and in the case of
pairs, scanning the barcode after
Saul, receiving end after receiving
the plug again
2. Receive a PC via RS232 serial
interface mode connection,
scanning the barcode after Saul,
receiving end after receiving the
plug again
3. Receive a PC via a serial port
connection, hold down the button
at the bottom for 8 s after system
in upgrade mode
Sender
upgrade
WN-T-K0000
1. The PC via USB cable
connection, and then send the
upgrade barcode, upgrade
equipment to restart after testing
@END
4.10 Wireless connectivity detection(★Note: this function only in a scanner connected to a
receiver)
Function
Command
barcode
Remark
@SET
Enable
connection
test
WN-T-C0001
This setting only in a scanner
connected to a receiver
*Disable
connection
test
WN-T-C0002
When more than a scanner
connected a receiving a case,
need to close the connection
test, factory default is close the
connection test
@END
4.11 The sender wired output
Function
Command
Barcode
Remark
@SET
* Enable USB
wired output
WN-T-L0000
1. After open the sender after
the PCB via USB cable
connection, connection can
be directly through the
normal USB transmission, do
not use the wireless
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
14 /29
transmission
Disable USB wired
output
WN-T-L0001
Shut down after insert USB
cable only allows charging,
only through wireless data
transmission
@END
Note☆:USB wired output is used only for the sender
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
15 /29
4.13 Serial port setting ★
Function
Command
barcode
Remark
@SET
3.10.1 Baud rate
2400
WN-R-D0000
4800
WN-R-D0001
*9600
WN-R-D0002
19200
WN-R-D0003
38400
WN-R-D0004
57600
WN-R-D0005
115200
WN-R-D0006
3.10.2 The length of the data
7 Data Bits
WN-R-D1002
*8 Data Bits
WN-R-D1001
3.10.3 Stop bit
*1 Stop Bit
WN-R-D1003
2 Stop Bit
WN-R-D1004
3.10.4 Parity bit
*No Parity
WN-R-D1005
Odd Parity
WN-R-D1006
Even Parity
WN-R-D1007
@END
Note★：The serial port setting can be used normal on support serial output equipment only
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
16 /29
4.15 Start symbol mode setting(Prefix) ★
Function
Command
barcode
Remark
@SET
*No start
symbol
WN-T-I0000
Custom
start
symbol+bar
code
WN-T-I0002
@END
The sample of start symbol mode setting：To set a start symbol “#Ab9”in barcode “1234567”,The barcode
data will be “#Ab91234567”.
1.Scan 【@SET】barcode.
2.Scan 【Custom start symbol + bar code】
3.Scan the following symbol【#】、【A】、【b】、【9】in turn.
4.Scan 【@END】barcode.
5. Max 10 digits for the prefix
4.16 End symbol mode setting(Suffix)
Function
Command
barcode
Remark
@SET
No end
symbol(suffix)
WN-T-I1000
No suffix
*Custom end
symbol(Suffix)
WN-T-I100A
Custom suffix can be
composed of ASCII
codes of any character,
customers can set
according to need
@END
The sample of end symbol mode setting：To set a start symbol “%B”in barcode “1234567”,The barcode data
will be “1234567%B”.
1.Scan【@SET】barcode ->2.Scan【Custom end symbol】barcode ->3. Scan the following symbol【%】、
【B】、in turn
4.Scan【Exit&Save】barcode
5. End symbol of factory reset: 0x0D(Enter)
6. End symbol of commonly used symbols：0x0D(Enter)，0x0A，0x09(Tab)
7. Suffix max 10 digits.
0x0D(Enter)
0x0A(newLine)
0x09(Tab)
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
17 /29
4.17 Sender end Prompt sound selection at the sender
When the wireless code scanner is in normal use, there are two prompt sounds. The first sound is the sound of
successful code reading, and the second sound is the sound of successful wireless transmission.
Function
Command
barcode
Remark
@SET
Enable turn on
sound
WN-T-
E0001
*Disable turn
on sound
WN-T-
E0002
Enable
transmit
successful
sound
WN-T-
E1001
*Disable
transmit
successful
sound
WN-T-
E1002
@END
Note: This function is mainly for the use of modules. Most modules have their own startup sound and
code scanning sound, so the motherboard’s startup sound and wireless transmission sound are turned on. The
two sounds overlap. So the added sound switch setting can cope with the module. The group voice is repeated and
the voice is mixed.
5Information instructions:
5.1 Receiver end instructions system
Serial
number
The type of status
indicators
The type of status indicators
State of the LED
Boot to detect hints
1
Wireless module to
detect anomalies
Short three beeps(high
frequency)
Red light blinks three times
2
External storage
module abnormal
Long two beeps (high
frequency)
Red light blinks twice
3
Power on
Short Four beeps（high／mid
／low frequency）
Green light continuous on
配对状态提示
4
Start the wireless
pairing
One short beeps（high
frequency）
LED light blinks once
5
Wireless pairing period
None
Red light blinks
6
Wireless pairing failure
None
Red light continuous on,
Green light off
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
18 /29
7
Wireless pairing
success
three long beeps（high／mid
／low frequency）big
difference
Green light continuous on
Setting state instructions
8
Enter setting mode
long one beep and short two
beeps （high／mid／low
frequency）
Green light blinks once
9
Exit & Save
Long one beep and short two
beeps（high／mid／low
frequency）
Green light blinks once
10
Setting command state
Long one beep and short one
beep（high／low frequency）
Green light continuous on
11
Effective command
Long one beep and two short
long（high／mid／low
frequency）
Green light blinks once
12
Non-effective
command
Long one beep（low
frequency）
Green light blinks once &
Red light blink once
Instructions of Inventory mode
13
Data uploaded
successfully
short one beep(high frequency)
Green light blinks once
14
Data uploaded failure
short three beeps(Intermediate
frequency)
Red light blinks three times
15
Data Overflow
long two beeps(high frequency)
Red light blinks twice
Real-time mode
17
Upload data successfully
Short one beep(high frequency)
Green light blinks once
18
Upload data failde
beeps(Intermediate frequency)
Red light blinks three times
Power status indicators
20
Charging status
None
Blue light on
21
Charging completed
None
Blue light off，Green light
on
22
Sleep／power off
Long one beep(Intermediate
frequency)
Light off
23
Low battery tips
None
Red light on (does not
affect the green light to red
light)
Quick command indicators
24
Quick instructions
Long one beep and short two
beeps（high／mid／low
frequency）
Green light blink once
Data Overflow
25
Data Overflow
Long one beep(Low frequency)
Red light blink once
5.2.1 Receiver end LED light indicator
Serial
number
System state
Buzzer announce
Indicator light
2.4G & 433 USB adapter
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
19 /29
1
power on within 30 seconds
---
Green light blink slowly
2
Boot after 30 seconds
---
Green light normally on
3
Receive the packet
---
Green light blink once
433 receiver
1
Electricity boot
Boot ringtone
2
power on within 30 seconds
None
Green light blink slowly
3
30 seconds later
None
Green light normally o n
4
Press the button to enter matching
state
None
Green light blink slowly
62.4G Wireless sending and receiving data packet format
6.1 bk2425 Infinite packet format
The statement field
Size
Description
U8 pkt_len
1byte
The length of the barcode
U8 pkt_check
1 byte
[[7] Address pairing indication marks
[6] 0: command package 1: The packet
[5] Barcode transmission complete indication
marks
0: Transfer to complete
1: unfinished
[4] Whether to show ID
0: ID hide
1: ID show
[3:0] system working mode
0:real-time mode
1:Inventroy mode
2:Cache mode
u8 pkt_part
1 byte
Long subcontract send number barcode data
u8 payload[29]
Max 29byte
Effective data area (Data of barcode)
7、Inventory mode to save and read data packet format：
The statement field
Size
Description
u16 len
2byte
The length of the barcode
u8 barcode_buf[520]
The size of the data
of effective
barcode data
Effective barcode data
7.1 Inventory model management information storage format:
Type
Fields
Length
Description
u8
sequence
1Byte
The order of the information stored in the
management sector
u16
barcode_count
2Byte
The number of barcode in the inventory model of
storage
U16
mode2_barcode_count
2Byte
Cache barcode number
Guangzhou Winson Information Technology Co.,Ltd www.winsonchina.com
20 /29
u32
write_addr
4Byte
The initial address of can be written (Inventory
mode)
u32
read_addr
4Byte
The initial address of can be read(Inventory
mode)
u32
mode2_write_addr
4Byte
Initial address of can be written in the
buffer(Cache mode)
u32
mode2_read_addr
4Byte
Initial address of can be read in the buffer(Cache
mode)
8、433 wireless data packet
The packet format
The statement field
Size
Description
U8 pkt_length
1byte
The length of the packet (The entire packet
length，contains the length of byte)
u8 pkt_part
1 byte
Long subcontract send number barcode data
U16 src_addr
2byte
source address
U32 dst_addr
2byte
destination address
U8 pkt_check
1 byte
[7] Address pairing indication marks
[6] 0: command package 1: The packet
[5] Barcode transmission complete indication marks
0: Transfer to complete
1: unfinished
[4] Whether to show ID
0: ID hide
1: ID show
[3:0] Reserved[0~7]
U8 pkt_repeat
1byte
Packets duplicate detection
u8 pkt_payload [56]
Max 56byte
Effective data area (Data of barcode)( Plan to
increase to120Bytes)
ACK packet format
The statement field
Size
Description
U8 pkt_length
1byte
The length of the packet (The entire packet length，
contains the length of byte)
U8 pkt_check
1 byte
[7] Address pairing indication marks
[6] 0: command packet 1: Data packet
[5] Bar code transmission complete indication marks
0: Transmission complete
1: Transmission failure
[4] Whether to showID
0: ID hide
1: ID show
[3:0] Reserved[0~7]
U16 src_addr
2byte
source address
U32 dst_addr
2byte
destination address
U16 cmd
2byte
The command of ACK return
Other Winson Barcode Reader manuals
