Wirepath Surveillance WPS-MNT-L-DOM User manual

WPS-MNT-L-DOM Dome Camera L Mount
Introduction
© 2012 Wirepath™ Surveillance
pg. 1
Installation Guidelines
Parts Included
Mounting
When mounting to a junction box, we recommend the use of metal junction boxes, doing so will
provide the most secure installation.
Weatherproong
While grommets and gaskets are provided to help block out moisture, we recommend adding a bead
of silicone around the edges of the mount for outdoor installations. This will help ensure that moisture will
not enter the wall.
Exploded View
A. (1) Camera Mount
B. (1) L Mount
C. (1) L Mount Gasket
D. (1) Wall Plate Adapter
Note: Make note of this diagram and letters as
they are used later in this document.
Not Shown
E. (2) M5x12L Round Head Philips
F. (2) M5x8L - Hex Thumb Screw
G. (2) #6-32x3/4”L - Flat Head Philips
H. (2) #8-32x3/4”L - Flat Head Philips
I. (4) M3x4 Pan Philips Head
J. (4) M6x20L Round Philips Head
K. (4) M6x20L Tab Fastner
L. (3) M4x10L - Round Head Philips with
Rubber Washers
M. (1) Manual
Wirepath™ Surveillance Camera Mount Plates have been designed to simplify installation and
overcome the complexity of concealing connections when installing Wirepath™ Surveillance cameras.
Each mount ts a variety of interior and exterior junction box sizes providing exibility during installation.
• Single
• Double
• 4” Square
Installation Manual
A
B
C
D
Exploded View

www.snapav.com Support: 866.838.5052
pg. 2
WPS-MNT-L-DOM Installation Manual
Installation
Important Note: To avoid damaging the dome surface during installation, keep the dome surface
away from walls and other objects. Do not remove the protective coating from the dome until
after the camera is mounted and the dome installed.
Microfiber or similar cloths can be abrasive, only use a dry eyeglasses cloth when cleaning the
lens to avoid damage that can blur the cameras image.
1. Install the Camera Wires into the Mount and Arm
2. Attach the Camera to the Mount
A. Remove the Camera Mount Plate (A) from the
L Bracket (B). Set the L Mount to the side.
B. Insert the wires from the camera through the
wire hole in the Camera Mount Plate (A) and
through the hole in the L Mount (B) pulling out
of the rear of the L Mount.
Tip: Placing the BNC Video Out in rst makes the
process quick
C. Secure the Camera Mount Plate (A) to the L
Mount (B) using the 4 M3x4 Pan Head screws
(I); ensure that it is fully tightened.
A. Remove the dome from the Camera Base
using the 3mm Allan key supplied with the
camera. Avoid contact of the dome with
surfaces in order to avoid scratching the dome
material.
B. Place the Camera Base on the Camera Mount
Plate (A) orientated as shown in Figure 2.
Tip: Inserting a mounting screw into the Camera
Base and then into the Camera Mount speeds up
the alignment process.
C. Secure the Camera Base to the Camera
Mount Plate using all 3 provided M4x10L Round
Head Philips (L) screws with rubber washers.
Note: To avoid moisture from entering the camera; ensure that the rubber grommets are on the screws during
installation
D. Loosely attach the dome onto the Camera. Note that you need to remove this later to setup the
camera once it is fully mounted. The assembly is now ready to be mounted to the wall.
Figure 1
Camera Base
*Note orientation of Camera Base and Camera
Mounting Plate. Identified holes must line up.
Figure 2
Align Holes*
Camera Mount
(bottom)
Camera Conduit
Connection

© 2012 Wirepath™ Surveillance
pg. 3
WPS-MNT-L-DOM Installation Manual
3. Attach the Wall Plate Adapter to the Wall
A. Pull the wires from the wall through the center
hole in the Wall Plate Adapter.
B. Align the Wall Plate Adapter mounting holes
with the holes on the Junction Box and secure
the Wall Plate Adapter.
Note: While a Single Gang box is shown, the
plate contains mounting holes for various types of
Junction Boxes or Masonry wall.
C. Secure the Wall Plate Adapter to the Wall
Plate Adapter. Note that the screws are
different depending on the junction box.
A. Single Gang
B. Double Gang
C. 4” Square
D. 4” Square (If 4” Square Box is rotated)
E. L Mount Alignment Posts
F. L Mount Lower Screws
Plate Mounting Holes
The Wall Plate Adapter included with the mount is designed to t a variety of junction box sizes.
The diagram below identies which holes to use when mounting to the various plates.
• Single
• Double
• 4” Square
A
A
B
B
C
D
D
C
B
B
E E
F F
Single Gang
Junction Box
Wall Plate
Figure 3

WPS-MNT-L-DOM Installation Manual
4. Attach the L Mount / Camera Assembly to the Wall
5. Finalize the Installation (outdoor cameras)
6. Setup the Camera
A. Place the L Mount Gasket on the rear of the L Mount with the groove towards the mount and the
tab lined up with the slot on the mount.
B. Place the L Mount (B) assembly onto the Wall Plate Adapter (D) aligning the Alignment Post (Figure
4) with the upper right mount screw location on the L Mount (B).
C. Loosely insert the one of the M5x8L Hex Thumb Screws (F), this will allow for the assembly to swing
down and be supported while the connections are made. (Figure 5)
D. Connect the wires from the wall to the Cameras wires at the end of the L Mount assembly and tuck
the wires into the junction box or wall.
E. Swing the assembly clockwise (Figure 5), aligning the upper left hand screw with the alignment post
on the Wall Plate Adapter. Insert the remaining M5x8L Hex Thumb Screw (F), tighten, and insert the
M5x12L Round Head Philips (E) into the lower mounting holes.
F. Tighten all screws.
For outdoor installations, we recommend adding a bead of silicone around the edges of the mount.
This will help ensure that moisture will not enter the wall.
Now that the camera is mounted, it can be setup for angle, zoom, and focus. Follow the instructions in
the manual for the Wirepath™ Surveillance camera that has been installed.
Figure 4
Alignment
Post
M5x8L Hex Thumb
Screw (F)
Figure 5
© 2012 Wirepath™ Surveillance
120829-1455
Contacting Technical Support
Phone: [phone]
Email: [email protected]