Wisenet HCF-8010V User manual

ANALOG CAMERA
User Manual
HCF-8010V

Analog Camera
User Manual
Copyright
©2019 Hanwha Techwin Co., Ltd. All rights reserved.
Trademark
Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the
registered trademark of their respective company.
Restriction
Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed,
partially or wholly, without formal authorization.
Disclaimer
Hanwha Techwin makes the best to verify the integrity and correctness of the contents in this document, but no
formal
guarantee shall be provided. Use of this document and the subsequent results shall be entirely on the user’s own
responsibility. Hanwha Techwin reserves the right to change the contents of this document without prior notice.
Design and specifications are subject to change without prior notice.

English_3
●SAFETY INFORMATION
Safety information
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric
shock is present within this unit.
This exclamation point symbol is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
• To prevent damage which may result in fire or electric shock hazard, do not expose this appliance
to rain or moisture.
• To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with
the installation instructions.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
3. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause
abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. insecure connection may cause fire.
5. When installing the camera, fasten it securely and firmly. The fall of camera may cause
personal injury.

4_ safety information
Safety information
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled
with water on top of the camera. doing so may cause personal injury due to fire, electric shock,
or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric
shock.
8. If any unusual smells or smoke come from the unit, stop using the product. in such case,
immediately disconnect the power source and contact the service center. continued use in
such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. never disassemble
or modify this product in any way. (Hanwha Techwin is not liable for problems caused by
unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. doing so may cause fire
or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong shock to it. Keep away from a location
subject to excessive vibrationor magnetic interference.
2. Do not install in a location subject to high temperature (over 55 °C), low temperature
(below -30 °C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and then
move or reinstall it.
4. Remove the power plug from the outlet when then there is a lightning. Neglecting to do so
may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may
damage the CMOS image sensor.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any time
10. Do not expose the camera to radioactivity. Radioactivity exposure may damage the CMOS.

English_5
●SAFETY INFORMATION
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions :
1) This device may not cause harmful interference, and
2) This device must accept any interference received including interference that may cause
undesired operation.
CAUTION
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own
expense.
IC Compliance Notice
This Class A digital apparatus meets all requirements of the Canadian
Interference.-Causing Equipment Regulations of ICES-003.
Correct disposal of batteries in this product
(Applicable in the European Union and other European countries with separate battery return systems.)
This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed
of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb
indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66. If
batteries are not properly disposed of, these substances can cause harm to human health or the environment.
To protect natural resources and to promote material reuse, please separate batteries from other types of waste and
recycle them through your local, free battery return system.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g.
charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate
these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material
resources.
Household users should contact either the retailer where they purchased this product, or their local government
office, for details of where and how they can take these items for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract.
This product and its electronic accessories should not be mixed with other commercial wastes for disposal.

6_ important safety instructions
Important safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the
cart/ apparatus combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as powersupply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. This product is intended to be supplied by a Listed Power Supply Unit marked “Class 2” or
“LPS” and rated from 24V AC (50/60 Hz) min. 0.2 A or 12V DC, min. 0.3 A.
16. If you use excessive force when installing the product, the camera may be damaged and
malfunction.
If you forcibly install the product using non-compliant tools, the product may be damaged.

English_7
●IMPORTANT SAFETY INSTRUCTIONS
17. Do not install the product in a place where chemical substances or oil mist exists or may be
generated. As edible oils such as soybean oil may damage or warp the product, do not install
the product in the kitchen or near the kitchen table.
This may cause damage to the product.
18. When installing the product, be careful not to allow the surface of the product to be stained
with chemical substance.
Some chemical solvents such as cleaner or adhesives may cause serious damage to the
product’s surface.
19. If you install/disassemble the product in a manner that has not been recommended, the
production functions/performance may not be guaranteed.
Install the product by referring to “Installation & connection” in the user manual.
20. Installing or using the product in water can cause serious damage to the product.
Apparatus shall not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, shall be placed on the apparatus
Hanwha Techwin cares for the environment at all product manufacturing
stages, and is taking measures to provide customers with more environmentally
friendly products.
The Eco mark represents Hanwha Techwin's devotion to creating
environmentally friendly products, and indicates that the product satisfies the
EU RoHS Directive.
Important safety instructions

8_ contents
Contents
OVERVIEW
9
9What's included
10 At a Glance
INSTALLATION
11
11 Before installation
11 Disassembling
12 Installation
CONNECTION
15
15 Connecting to Monitor
16 Connecting to Power
CAMERA OPERATION
18
18 Menu Configuration
18 Camera setup
TROUBLESHOOTING
24
24 Troubleshooting
SPECIFICATIONS
25
25 Specifications
27 Dimension

English_9
●INTRODUCTION
Overview
WHAT'S INCLUDED
Please check if your camera and accessories are all included in the product package.
(As for each sales country, accessories are not the same.)
HCF-8010V
ANALOG CAMERA
Quick Guide
Camera Quick Manual
Warranty card Template
Tapping Screw Anchor
Screw

10_ overview
Overview
AT A GLANCE
Appearance
1 Camera
2 Mounting Plate: Used to mount the camera.
3 Power Input Connector (Dual (24V AC & 12V DC))
4 Video Output Jack : Outputs a video in the set video format.
5 Video Format Setting Switch: Allows to set to a video format (TVI/AHD/CVBS) of your choice.
6 Screw Hole: Used to assemble/disassemble the camera and plate.
6
2
1
5
4
3

English_11
●INSTALLATION
BEFORE INSTALLATION
Ensure you read out the following instructions before installing the camera:
yYou have to check whether the location (ceiling or wall) can bear fve times the weight
of your camera.
yDon’t let the cable to be caught in improper place or the electric line cover to be damaged.
Otherwise it may cause a breakdown or fre.
yBefore installing your camera, you have to adjust the front direction.
yWhen installing your camera, don’t allow any person to approach the installation site.
DISASSEMBLING
1. Remove the screws on the side using a phillips screwdriver.
2. Turn the camera body clockwise to remove the mounting plate.
➋
➊

Close Open
Installation

Installation
12_ Installation
INSTALLATION
1. Attach the installation template to the selected area and punch 4 holes as shown
in the fgure.

English_13
●INSTALLATION
2. Align the installation holes of the camera and use the tapping screws to fx the
mounting plate.
`Make sure that the <FRONT> marking on the bottom mounting plate is turned towards
the direction to monitor.
Mounting plate
Tapping Screw
3. Refer to“Disassembling”to attach the camera to the mounting plate.

14_ Installation
Optional Accessories for Installation
For your easier installation, you can purchase appropriate optional accessories available.
1. Install the mounting plate to the bracket (SBP-300HMW7 /SBP-122HMW) as shown below,
and then attach the camera to the mounting plate.
Bracket
(SBP-300HMW7 /SBP-122HMW)
Mounting plate
Screw
2. See “Disassembling” to attach the camera to the mounting plate.
Bracket
(SBP-300HMW7 /SBP-122HMW)
Mounting plate
Camera

English_15
●CONNECTION
connection
CONNECTING TO MONITOR
Connect the Video OUT port on the rear panel of the camera to a DVR.
RECHDDALARM NETWORKBACKUP POWER
DVR
Monitor
yAs the connecting method varies with the instruments, refer to the manual supplied
with the instrument.
yOnly connect the cable when the power is turned o.
M`This product supports 3 video output formats of AHD, CVBS, and TVI.
The default is AHD. Select the video output appropriate for your DVR.

Connection
16_ connection
CONNECTING TO POWER
You can connect power as shown in the following figure.
Power Input Terminal
When the resistance value of copper wire is at [20°C(68°F)]
Copper wire size (AWG) #24 (0.22 mm2)#22 (0.33 mm2)#20 (0.52 mm2)#18 (0.83 mm2)
Resistance value(/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
yAs shown in the table above, voltage decreases as the wire gets longer.
Therefore use of an excessively long adaptor output line for connection to the camera
may aect the performance of the camera.
 Standard voltage for camera operation : DC 12 V ± 10%, AC 24 V ± 10%
 There may be some deviation in voltage drop depending on the type of wire and the
manufacturer.
M
`Be sure to connect power only after all the installation is complete.

English_17
●CONNECTION
- Video Cable
The camera's video output port is connected to the DVR with a BNC coaxial cable,
shown below.
Distance
Recommended Cable
Specification
500 m 5C2V
M`It is recommended that pure copper coax cable is used and not copper coated steel, as
this will cause issues with the communication over the coaxial cable.
`To ensure picture quality, only single-channel video output connector can be used
while camera connected to other video equipments.

18_ camera operation
MENU CONFIGURATION
MAIN SETUP
VIDEO FORMAT
◦FORMAT ◦RETURN
WHITE BAL
◦ATW ◦INDOOR ◦OUTDOOR
◦MANUAL ◦ AWC →SET
◦RETURN
EXPOSURE
◦BRIGHTNESS ◦SHUTTER ◦AGC
◦SSNR ◦RETURN
BACKLIGHT
◦USER BLC ◦D-WDR ◦RETURN
SPECIAL
◦LANGUAGE ◦IMAGE ADJ ◦DAY&NIGHT
◦RETURN
EXIT
◦SAVE&END ◦NOT SAVE ◦RESET
CAMERA SETUP
VIDEO FORMAT
1. From the Setup menu, select the
<VIDEO FORMAT >.
2. Select the VIDEO mode.
yThe video output can be selected
from AHD/CVBS/TVI.
camera operation
MAIN SETUP
1. VIDEO FORMAT FORMAT
2. WHITE BAL ATW
3. EXPOSURE
4. BACKLIGHT OFF
5. SPECIAL
6. EXIT SAVE

English_19
●CAMERA OPERATION
White Bal (White Balance)
Use the White Balance function to adjust the screen color.
1. From the Setup menu, select the
<White Bal>.
2. Select the desired mode.
 Select one of the following 5 modes,
as appropriate for your purpose.
yATW : Select this when the color tem-
perature is between 2,400K and
10,500K.
y
INDOOR : Select this when the color temperature is between 4,500K and 8,500K.
Automatically adjusts the camera color for optimization to the indoor
environment.
y
OUTDOOR : Select this when the color temperature is between 1,800K and 10,500K.
Automatically adjusts the camera color for optimization to the outdoor environ-
ment.
yMANUAL :
Select this to fne-tune White
Balance manually. Set White
Balance frst by using the ATW
or AWC mode. After that button
to MANUAL mode, fne-tune
the White Balance and the
Function Setup switch.
yAWC
 SET : To fnd the optimal luminance level for the current environment, point the camera
towards a sheet of white paper and press the Set button. If the environment
changes, readjust it.
M
`White Balance may not work properly under the following conditions. In this case
select the AWC mode.
1 Select this When the color temperature of environment surrounding the subject
is out of the control range (e.g. clear sky, or sunset)
2 When the ambient illumination of the subject is dim.
`If the camera is directed towards a fluorescent light or is installed in a place where
illumination changes dramatically, the White Balance operation may become
unstable.
MAIN SETUP
1.
VIDEO FORMAT FORMAT
2. WHITE BAL ATW
3. EXPOSURE
4. BACKLIGHT OFF
5. SPECIAL
6. EXIT SAVE
WB MANUAL
1. RED GAIN
IIIIIIIIIIIIIIIIIIIII
50
2. BLUE GAIN
IIIIIIIIIIIIIIIIIIIII
40
3. RETURN

20_ camera operation
Camera operation
EXPOSURE
1. From the Setup menu, select the
<EXPOSURE>.
2. Select each item and set it properly.
yBRIGHTNESS :
Adjusts the video
brightness.
ySHUTTER : You can select the shutter.
- MIN/MAX : 1/30s~ 1/50,000s (NTSC ),
1/25s~ 1/50,000s (PAL)
- A.FLK : Select this when you experience picture flicker, this happen when there is
a clash with the installed lighting frequency.
M
`The greater the shutter value the brighter the screen is but the more the residual
images of objects there are.
`If the min shutter value is large, it can cause noise, spots and white areas but still operate
normally.
`If you do not use the AGC mode on the exposure menu, it cannot be set above
1/60sec.
`Depending on the setting range of the minimal/maximal shutter, the screen
exposure can become saturated.
yAGC (OFF/LOW/MIDDLE/HIGH) :
The higher the gain level, the brighter the screen - but the greater the noise.
ySSNR : This function reduces the background noise in a low luminance environment.
- 2DNR (OFF/LOW/MIDDLE/HIGH)
- 3DNR (OFF/LOW/MIDDLE/HIGH)
M
`When adjusting the noise reduction level in the SSNR mode, remember that the
higher the level set, the more the noise level will be reduced, as will the brightness of
the image.
BACKLIGHT
MAIN SETUP
1.
VIDEO FORMAT FORMAT
2. WHITE BAL ATW
3. EXPOSURE
4. BACKLIGHT OFF
5. SPECIAL
6. EXIT SAVE