Wisenet SLA-T1080FA User manual

SLA-T1080FA/T2480A/T2480VA/T4680A/T4680VA
NETWORK CAMERA
Quick Guide

1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp
cloth.
(Do not use a detergent or cosmetic products that contain alcohol, solvents or
surfactants or oil constituents as they may deform or cause damage to the product.)
7. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.

13. Unplug this apparatus during lighting storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
15. This Lens module has to be connected with equipment, which supplied by a power supply
unit marked “Class 2” or “LPS”.
Any changes or modifications in construction of this device which are not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

4
COMPONENT
As for each sales country, accessories are not the same.
~SLA-T1080FA
~SLA-T2480A

5
~SLA-T4680A
~SLA-T2480VA
~SLA-T4680VA

INSTALLATION
6

INSTALLATION
7
1-1
~SLA-T1080FA
1-2

INSTALLATION
8
1-3
1-4

INSTALLATION
9
1-5

INSTALLATION
10
2-2
2-1
~SLA-T2480A/SLA-T4680A

INSTALLATION
11
2-3
2-4

INSTALLATION
12
2-5

INSTALLATION
13
3-2
3-1
~SLA-T2480VA/SLA-T4680VA

INSTALLATION
14
3-3
3-4
* This only applies to the SLA-T2480VA.

INSTALLATION
15
3-5

CONNECT LENS MODULE CABLE TO LENS MODULE
16
1
2

CONNECT LENS MODULE CABLE TO LENS MODULE
17
4
3

18
ADJUST THE LENGTH OF THE CABLE FOR CONNECTING THE
LENS MODULE
1
2

19
ADJUST THE LENGTH OF THE CABLE FOR CONNECTING THE
LENS MODULE
4
3
1
6
Number Color
1Black
2Red
3Bule
4Orange
5White
6Green

20
ADJUST THE LENGTH OF THE CABLE FOR CONNECTING THE
LENS MODULE
5
6