Wolf ` AGE24 User manual

Item #_____________ C.S.I. Section 11420
Wolf Range Company
Division of ITW Food Equipment Group LLC
[phone]
www.wolfrange.com
F-36977 (02-08)
BASIC MODELS:
AGE24 24" w x 24" d griddle plate
AGE36 36" w x 24" d griddle plate
AGE48 48" w x 24" d griddle plate
AGE60 60" w x 24" d griddle plate
AGE72 72" w x 24" d griddle plate
KEY FEATURES:
➤Stainless steel front, sides and 4" front top ledge.
➤Fully welded stainless and aluminized steel body frame.
➤11" low profile cooking height on 4" adjustable legs.
➤1" thick polished steel griddle plate robotically welded to
stainless steel back and tapered side splashers.
➤One 30,000 BTU/hr. “U” shaped aluminized steel burner
and 120 volt snap action thermostat for each 12" of griddle
width. Temperature adjusts from 150° to 450°F.
➤Electronic ignition.
➤31/2" wide stainless steel front grease trough.
➤Large capacity 67/8" wide x 30" deep x 21/2" high stainless
steel grease drawer.
➤3/4" rear gas connection and gas pressure regulator. 120
volt control circuit, 6' cord with 3 prong plug.
➤One year limited parts and labor warranty.
OPTIONAL FEATURES:
➤Leg Lengths: 4", 55⁄8", 8", 10", 113⁄4"
➤Chrome-plated cooking surface.
➤Rear grease trough.
➤Full or partially grooved griddle plates.
➤Stainless steel stand with marine edge and casters.
➤Towel bar.
➤Full width cutting board.
DESCRIPTION:
Low profile heavy duty gas griddle, Wolf Model No. ________.
Stainless steel front, sides and 4" front top ledge. Fully welded
stainless and aluminized steel body frame. 11" low profile
cooking height on 4" legs. 1" thick polished steel griddle
plate robotically welded to stainless steel back and tapered
side splashers. One 30,000 BTU/hr. “U” shaped aluminized
steel burner and 120 volt snap action thermostat for each
12" of griddle width. Temperature adjusts from 150° to 450°F.
Electronic ignition. 31/2" wide stainless steel front grease trough.
Large capacity 67/8" wide x 30" deep x 21/2" high stainless steel
grease drawer. 3/4" rear gas connection and gas pressure
regulator. 120 volt control circuit, 6' cord with 3 prong plug.
Exterior dimensions: _____" w x 33" d x 151/2" h on 4" legs.
MODEL: AGE SERIES Low Profile Heavy-Duty Gas Griddle
Approved by_______________________
Date: _____________________________
SPECIFY TYPE OF GAS WHEN ORDERING.
SPECIFY ALTITUDE WHEN ABOVE 2,000 FT.
Model AGE36
CSA design certified. NSF listed.
MODEL: AGE SERIES
LOW PROFILE HEAVY-DUTY
GAS GRIDDLE

NOTE: In line with its policy to continually improve its product, Wolf Range Company
reserves the right to change materials and specifications without notice.
This appliance is manufactured for commercial use only and is not intended for home use.
F-36977 (02-08)
MODEL: AGE SERIES
LOW PROFILE HEAVY-DUTY
GAS GRIDDLE
INSTALLATION REQUIREMENTS:
1. A gas pressure regulator supplied with the unit must be
installed:
Natural Gas 5.0" (127 mm) W.C.
Propane Gas 10.0" (254 mm) W.C.
2. All models require a 6" (152 mm) clearance at both sides
and rear adjacent to combustible and non-combustible
construction.
3. These units are manufactured for installation in accordance
with ANSI/NFPA-70, National Electrical code.
An adequate ventilation system is required for Commercial
Cooking Equipment (NFPA No. 96). Information may be
OVERALL WORKING NO. OF TOTAL NO. OF APPROX.
MODEL WIDTH DEPTH HEIGHT* HEIGHT* BURNERS BTU/HR. DRAWERS** SHP.WT.
AGE24 24" 33" 15½" 11³⁄₈" 2 60,000 1 285 lbs./129 kg
AGE36 36" 33" 15½" 11³⁄₈"3 90,000 1 400 lbs./181 kg
AGE48 48" 33" 15½" 11³⁄₈"4 120,000 1 480 lbs./218 kg
AGE60 60" 33" 15½" 11³⁄₈"5 150,000 2 650 lbs./295 kg
AGE72 72" 33" 15½" 11³⁄₈"6 180,000 2 790 lbs./358 kg
*These are nominal dimensions and can vary by +1.75" with adjustable legs.
**All Rear Grease option griddles have only one (1) grease drawer on the left side.
obtained by writing to the National Fire ProtectionAssociation,
Batterymarch Park, Quincy, MA 02169.
4. These units are manufactured for installation in accordance
with National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (lat-
est edition). Copies may be obtained from The American
Gas Association, Accredited Standards Committee Z223
@ 400N. Capital St. NW, Washington, DC 20001, or the
Secretary Standards Council, NFPA, 1 Batterymarch Park,
Quincy, MA 02169-7471.
NOTE: In the Commonwealth of Massachusetts
All gas appliances vented through a ventilation hood or
exhaust system equipped with a damper or with a power
means of exhaust shall comply with 248 CMR.
5. This appliance is manufactured for commercial installation
only and is not intended for home use.