Woods 600000 User manual

VERTICAL/HORIZONTAL LOG SPLITTERS
27 & 28 TON MODEL
MODEL NUMBER
600000, 600001
Owner’s Manual P/N 597612
ASSEMBLY & OPERATING INSTRUCTIONS
WARNING: All operators must read this manual before operating this log
splitter. Follow the safety instructions in the manual and in decals attached to
the product. Failure to do so could result in serious injury or death.
(Rev. AB 7/21/2017)

Page 2
Record the information below for future reference.
Model No. _________________________
Date of Purchase ___________________
Serial Number Label Location
Tank Plate Below Beam
Serial No. __________________________
Place of Purchase ___________________
___________________
___________________
___________________
WARNING: Read and thoroughly understand all instructions in this manual and on safety decals
before assembling or operating this log splitter. Failure to do so may cause serious injury or
death. Do not allow anyone to operate this log splitter who has not read this manual. As with all
power equipment, a log splitter can be dangerous if assembled or used improperly. Do not
operate this log splitter if you have any questions concerning safe operation. To get answers to
any questions, call our technical support department at 1-800-319-6637.

Page 3
TABLE OF CONTENTS
IMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PERSONAL PROTECTIVE EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . 5
PREPARATION OF THE LOG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
OPERATION OF THE LOG SPLITTER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
GENERAL REPAIR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
REPAIR AND MAINTENANCE SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
FIRE PREVENTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TOWING SAFETY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SAFETY DECALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 9
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
ASSEMBLY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
HYDRAULIC OIL RECOMMENDATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . 14
ENGINE OIL RECOMMENDATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 15
STARTING INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 - 15
OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
TOWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 - 20
WARRANTY SERVICE INFORMATION . . . . . . . . . . . . . . . . . INSIDE BACK COVER
GENERAL INFORMATION
The purpose of this manual is to assist you in operating
and maintaining your log splitter. Read it carefully. It
furnishes information and instructions that will help you
achieve years of dependable performance. These
instructions have been compiled from extensive field
experience and engineering data. Some information
may be general in nature due to unknown and varying
operating conditions. However, through experience
and these instructions, you should be able to develop
procedures suitable to your particular situation.
The illustrations and data used in this manual were cur-
rent at the time of printing but, due to possible inline
production changes, your machine may vary slightly in
detail. We reserve the right to redesign and change the
machines as may be necessary without notification.
Throughout this manual, references are made to right
and left direction These are determined by standing
behind the equipment facing the direction of forward
travel.

Page 4
SPECIFICATIONS
* Tonnage and cycle times vary dependent upon mechanical and environmental conditions.
** Use replacement filter element #578459. This filter contains an inner bypass that is required for this hydraulic circuit.
Model No. 600000 Model No. 600001
Engine Kohler SH265 Honda GC190
Pump Two-Stage 13 GPM Two-Stage 13 GPM
Cylinder 4.5 in. Diameter x 24 in
Stroke
4.5 in. Diameter x 24 in
Stroke
Valve Auto-Return Auto-Return
Maximum Splitting Force
*
27 Tons 28 Tons
Maximum Log Length 24.5 in. 24.5 in.
Cycle Time
*
13 Seconds 13 Seconds
Wheels 4.80 x 8 in. DOT Approved
rated for up to 45 MPH
4.80 x 8 in. DOT Approved
rated for up to 45 MPH
Wedge 8 in. High 8 in. High
Hydraulic Capacity 6.5 Gallons 6.5 Gallons
Filter
**
Spin-On Replaceable Spin-On Replaceable
Height
70.9 in. In Vertical Position
41.5 in. In Horizontal Position
70.9 in. In Vertical Position
41.5 in. In Horizontal Position
Width 48.2 in. 48.2 in.
Shipping Weight 525 lbs. 525 lbs.

Page 5
• NEVER use this log splitter for any other purposes than splitting wood. It is designed for this use only . Any other
use can cause serious injury or death.
• BEFORE operating this log splitter, make sure that you wear safety gear such as goggles or safety glasses, steel
toed shoes and tight fitting gloves (without loose cuffs or draw strings). Always wear a protective hearing device
when operating this log splitter.
Both ends of the log should be cut as square as possible to help prevent the log from riding out of the splitter during
operation. Do not split logs greater than 24-1/2 inches in length.
ONLY one operator may operate the log splitter from the
operator zone as shown in the diagram. Keep all bystanders
and pets away. The operator has the safest and most
efficient access to the control valve and the beam in this
location. Operating the log splitter in another location can
result in serious injury or death.
• ALWAYS block the wheels to prevent movement of the log splitter while in operation.
• KNOW how to stop the log splitter and disengage the controls before operating it.
• NEVER place hands or feet between the log and splitting wedge during forward or reverse strokes as this could
result in serious injury or death.
• NEVER straddle or step over the log splitter during operation.
• NEVER reach or bend over the log splitter to pick up a log.
• NEVER try to split two logs on top of each other.
• NEVER try to cross split a log.
• NEVER attempt to load the log splitter when the ram or wedge is in motion.
• NEVER use your foot, a rope, or any extension device to operate the control lever on the valve. Only use hand.
• NEVER move the log splitter while the engine is running. Shut off the engine if you are leaving the log splitter, even
for a short period of time.
• NEVER touch the muffler and hot areas of the engine during operation. Wait until the engine cools down.
• IMPORTANT Holding the valve in the “actuate” position at the end of the stroke may damage the log splitter.
• ALWAYS use extra care when splitting logs with unsquare ends.

Page 6
• NEVER operate your log splitter when it is in poor mechanical condition or in need of repair.
• NEVER alter your log splitter in any manner. Such alterations may cause your log splitter to be unsafe and will void
the warranty.
• NEVER tamper with the engine to run it at excessive speeds. The maximum engine speed is preset by the manu-
facturer and is within safety limits. Refer to the engine owner’s manual for your particular log splitter.
• NEVER perform any service or repair on your log splitter without first removing the spark plug wire.
• ALWAYS perform all recommended maintenance procedures before using your log splitter.
• ALWAYS check the level of hydraulic oil and engine oil before operation.
• ALWAYS periodically check that all nuts, bolts, screws, hydraulic fittings and hose clamps are tight.
• ALWAYS replace all damaged or worn parts immediately.
• ALWAYS be sure that all replacement parts meet manufacturer’s specifications.
• The hydraulic system of your log splitter requires careful inspection along with the mechanical parts. Be sure to
replace frayed, kinked cracked or otherwise damaged hydraulic hoses or hydraulic components.
• NEVER check for leaks of hydraulic fluid with your hand. Fluid escaping from a small hole can be almost invisible.
Escaping fluid under pressure can have sufficient force to penetrate skin causing SERIOUS INJURY or even
DEATH. Leaks can be safely detected by passing a piece of cardboard over the suspected leak and looking for dis-
coloration.
• ALWAYS seek professional medical attention immediately if injured by escaping hydraulic fluid. Serious infection or
reaction can develop if proper medical treatment is not administered immediately.
• NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. The tank could contain
hot oil under pressure which could result in serious injury.
• NEVER adjust the hydraulic valve. The pressure relief valve on your log splitter is preset at the factory. Only a qual-
ified service technician should perform this adjustment.
• ALWAYS be sure to relieve all pressure by shutting off the engine and moving the valve control handle back and
forth should it become necessary to loosen or remove any hydraulic fitting.
• NEVER operate your log splitter near a flame or spark, or smoke during operation. Hydraulic oil and gasoline are
flammable and can explode.
• NEVER fill the gas tank while the engine is hot or running. Allow the engine to cool before refueling.
• ONLY refuel your log splitter in a clear, well ventilated area with no gas fumes or spilled gas.
• ALWAYS replace the gas cap securely.
• If gasoline has spilled, move the log splitter away from the area of the spill and avoid creating any source of ignition
until the spilled gas has evaporated.
• ALWAYS drain the fuel tank prior to storage to avoid the potential fire hazard.
• ALWAYS clean wood debris from on and around the engine and muffler.

Page 7
• ALWAYS store gasoline in an approved, tightly sealed container and away from heating appliances. Store the con-
tainer in a cool, dry place.
IMPORTANT NOTE - (Spark Arrester)
As a precautionary measure against possible flying sparks, always take a Class B fire extinguisher with you when oper-
ating this log splitter in dry areas. This log splitter is equipped with an internal combustion engine and should not be
used on or near any unimproved forest-covered, brush-covered or grass-covered land unless the engine’s exhaust
system is equipped with a spark arrester meeting applicable local or state laws (if any). If a spark arrester is used, it
should be maintained in effective working order by the operator. In the state of California, a spark arrester is required by
law. Other states have similar laws. Federal laws apply on federal lands. A spark arrester muffler is optional and avail-
able as an accessory at your nearest engine dealer. Always check the legal requirements in your area.
• NEVER move your log splitter over hilly or uneven terrain without a tow vehicle or adequate help.
• NEVER carry any cargo or wood on your log splitter.
• NEVER allow anyone to sit or ride on your log splitter.
• NEVER exceed 45 mph when towing your log splitter. Towing the log splitter at speeds higher than 45 mph could
result in loss of control, damage to the equipment, or serious injury or death. Adjust towing speed for terrain and
conditions. Be extra cautious when towing over rough terrain, especially railroad crossings, and avoid sharp turns
and steep angles when towing your log splitter.
• NEVER exceed weight capacity of ball or load limits of coupler.
• ALWAYS confirm coupler tightness each time before towing and after towing 50 miles.
• ALWAYS disconnect your log splitter from the towing vehicle before operating it.
• ALWAYS be careful when backing up your log splitter in tow. It could jackknife.
• ALWAYS allow for added length of your log splitter when turning, parking, crossing intersections and in all driving
situations.
• ALWAYS use safety chains when towing your log splitter.
• ALWAYS check all local and state regulations regarding towing, licensing, and lights before towing your log splitter.
• ALWAYS check before towing to make sure that the log splitter is correctly and securely attached to the towing
vehicle and that the safety chains are secured to the hitch or bumper of the vehicle with enough slack to allow turning.
• ALWAYS use a Class 1, 2” ball with this log splitter.
• ALWAYS replace ball or coupler if damaged or excessively worn.
• ALWAYS turn the fuel shut off valve on the engine to the “OFF” position before towing the log splitter. Failure to do
so may result in flooding the engine.
• ALWAYS lift support stands and have beam pinned down and forward for transport.

Page 8
Make sure that all safety warning decals are in good condition and readable. Always replace missing or defaced decals. Contact Or
Woods Equipment Company at 1-800-319-6637 or www.woodsequipment.com for replacement decals.
PART NUMBER: S52062500
LOCATION: TOP, FRONT END OF TONGUE
PART NUMBER: S52062200
LOCATION: TOP OF CYLINDER
PART NUMBER: S52062400
LOCATION: HYDRAULIC TANK
LOWER TANK, RIGHT CORNER

Page 9
PART NUMBER: S52062100
LOCATION: TOP OF HYDRAULIC
CYLINDER
PART NUMBER: S52062300
LOCATION: STRIPPER PLATE,
OPERATOR SIDE
PART NUMBER: S52062400
LOCATION: HYDRAULIC TANK
LOWER TANK, RIGHT CORNER

Page 10
NOTE: This log splitter was partially assembled at the factory. Refer to the drawings and parts list should it become
necessary to disassemble the unit for repair or replacement of parts. The drawings in this manual are for refer-
ence only. Some of the components on your log splitter may look slightly different.
STEP 1:
Remove all the components from the crate. Inspect each piece for shipping damage. If any part is damaged, contact
your dealer or delivering carrier.
STEP 2:
Install wheel spacer (5) on axle prior to attaching wheel. Attach the two wheels (2) to the tank assembly (3) wheel spin-
dles using 3/4 flat washers (9), 3/4 NF slotted nuts (8), 1/8 x 1-1/2 cotter pins (6) and hub caps (7). These items are in
the hardware package. Tighten the slotted nuts and make sure the wheels rotate freely.
ITEM DESCRIPTION QTY
1Tongue Assembly 1
2Wheel 2
3Tank Assembly 1
4Beam Assembly 1
ITEM DESCRIPTION QTY
2Wheel 2
3Tank Assembly 1
5Spacer 2
61/8 x 1-1/2 Cotter Pin 2
7Hub Cap 2
83/4 NF Slotted Nut 2
93/4 Flat Washer 2