Hyundai HYLS7TE User manual

!
!"#$%&%##'&(")(!!'
' '
'
'
'
'
'
'
'
'
'
'
'
'
'
'
!"#$%"&#$'(!)*%$
#)(+$(,+$&,+)#'*(,+$*-)$),*.#)$/(,&(0$
1)!"#)$"2)#(*.,3$/(4-.,)$
$
$
$
"#$%&!'(")%*!+! ,-./!
0%*12&!'(")%*!+!!!! !
!
)345!63789!:;6<8=!>:7!?8=@>9!:;6<8=!6>A!<8!B3;:7!3:!458!6>@:!9><89C!
D3;!?53;97!=8E3=7!<345!3B!4586!@:!>!?>B8!F9>E8!B3=!B;4;=8!;?8C!
!
!
!
'567$*89:$/5;<5=$>?@$!<A<@7$#7>7@7;B7$
$
$
$
$
$
$
$
$
$
$
*++$+,-"".#"/01233'#'
'
'
'
'
'
'
'
'
'
'
'
!
'
'
'
'
'
'
'
'
'
'
'
!
C$*",$0"3$'20.**)#$
D$"E;7@F:$/5;<5=$
!"!#$%&#'($'")*'+,"&$$!%
-."+($!
ELECTRIC 7T LOG SPLITTER
HYLS7TE

2
65575UK00M103.indd 2
2017/9/11 9:04:22
SAFETY WARNINGS & INSTRUCTIONS
SAFETY WARNINGS & CAUTIONS
•UNDERSTAND YOUR LOG SPLITTER
Read and understand the owner's manual and labels affixed to
the log splitter. Learn its application and limitations as well as the
specific potential hazards peculiar to it.
•DRUGS, ALCOHOL ANDMEDICATION
Do not operate the log splitter while under the influence of drugs,
alcohol, or any medication that could affect your ability to use it
properly.
•AVOID DANGEROUS CONDITIONS
Put the log splitter on a 60 - 75cm high, stable, flat, and level work
bench where there is plenty of room for handling, and help the
operator stay altert. Bolt the log splitter to the work surface if it
tends to slip, walk, or slide.
Keep your work area clean and well lighted. Cluttered areas
invites injuries.
Do not use the log splitter in wet or damp areas or expose it to
rain.
Do not use it in areas where fumes from paint, solvents or
flammable liquids pose a potential hazard.
•INSPECT YOUR LOG SPLITTER
Check your log splitter before turning it on. Keep guards in place
and in working order. Form a habit of checking to see that keys
and adjusting wrenches are removed from tool area before turning
it on. Replace damaged, missing or failed parts before using it.
•DRESS PROPERLY
Do not wear loose clothing, gloves, neckties or jewelry (rings,
wrist watches). They can be caught in moving parts.
Protective electrically non conductive gloves and non-skid
footwear are recommended when working. Wear protective hair
covering to contain long hair, preventing it from get caught in
machinery.
•PROTECT YOUR EYES AND FACE
Any log splitter may throw foreign objects into the eyes. This can
cause permanent eye damage. Always wear safety goggles.
Everyday eyeglasses have only impact resistant lenses. They are
not safety glasses.
Do not put the log splitter on the ground for operations. This is
awkward operating position that the operator has to bring his face
close to the machine, and thus risks being struck by wood chips
or debris.
SYMBOL AFFIXED TO THE
MACHINE

3
65575UK00M103.indd 3
2017/9/11 9:04:23
•EXTENSION CORDS
Improper use of extension cords may cause inefficient operation
of the log splitter which can result in overheating. Be sure the
extension cord is no longer than 10m and its section is no less
than 2.5mm²to allow sufficient current flow to the motor.
Avoid use of free and inadequately insulated connections.
Connections must be made with protected material suitable for
outdoor use.
•AVOID ELECTRICAL SHOCK
Check that the electric circuit is adequately protected and that
it corresponds with the power, voltage and frequency of the
motor. Check that there is a ground connection, and a regulation
differential switch upstream.
Ground the log splitter. Prevent body contact with grounded
surfaces: pipes, radiators, ranges, and refrigerator enclosures.
Never open the pushbutton box on the motor. Should this be
necessary, contact a qualified electrician.
Mark sure your fingers do not touch the plug's metal prongs when
plugging or unplugging the log splitter.
•KEEP VISITORS AND CHILDREN AWAY
The log splitter must be always operated by one person only.
Other people should keep a safe distance from the work area,
especially when the log splitter is under operations. Never use
another people to help you with freeing jammed log.
•INSPECT YOUR LOG
Make sure there are no nails or foreign objects in logs to be split.
The ends of the logs must be cut square. Branches must be cut of
flush with the trunk.
•DON'T OVERREACH
Floor must not be slippery.
Keep proper footing and balance at all times.
Never stand on log splitter. Serious injury could occur if the tool
is tipped or if the cutting tools is unintentionally contacted. Do not
store anything above or near the log splitter where anyone might
stand on the tool to reach them.
•AVOID INJURY FROM UNEXPECTED ACCIDENT
Always pay full attention to the movement of the log pusher.
Do not attempt to load the log on until the log pusher has stopped.
Keep hands out of the way of all moving parts.
•PROTECT YOUR HANDS
Keep you hands away from splits and cracks which open in the
log; They may close suddenly and crush or amputate your hands.
Do not remove jammed logs with you hands.

4
65575UK00M103.indd 4
2017/9/11 9:04:23
•DON'T FORCE TOOL
It will do a better and safer job at its design rate. Never try to split
logs larger than those indicated in the specifications table. This
could be dangerous and may damage the machine.
Don't use log splitter for a purpose for which it was not intended.
•NEVER LEAVE TOOLRUNNING UNATTENDED
Don't leave tool until it has come to a complete stop.
•DISCONNECT POWER
Unplug when not in use, before making adjustments, changing
parts, cleaning, or working on the log splitter; Consult technical
manual before servicing.
•PROTECT THE ENVIRONMENT
Take used oil to an authorized collection point or follow the
stipulations in the country where the log splitter is used.
Do not discharge into drains, soil or water.
•MAINTAIN YOUR LOG SPLITTER WITH CARE
Keep the log splitter clean for best and safest performance.
•MAKE THE WORKSHOP CHILDPROOF
Lock the shop. Disconnect master switches. Store the log splitter
away from children and others not qualified to use it.
TABLE OF CONTENTS
Safety Warnings & Cautions. ................................................................................................. 2
Application Conditions............................................................................................................ 5
Specifications. ........................................................................................................................ 5
Electrical Requirements. ........................................................................................................ 5
Set up and Preparation for Operation. ................................................................................... 6
Wiring Diagram....................................................................................................................... 7
Plumbing Diagram.................................................................................................................. 7
Log Splitter Operation. ........................................................................................................... 8
Freeing a Jammed Log. ......................................................................................................... 9
Replacing Hydraulic Oil. ....................................................................................................... 10
Sharpening Wedge............................................................................................................... 10
Trouble Shooting. ..................................................................................................................11
Parts Schematic. .................................................................................................................. 12

5
65575UK00M103.indd 5
2017/9/11 9:04:23
APPLICATION CONDITIONS
This log splitter is a home use model. It is designed for operating under ambient
temperatures between +5℃ and 40℃ and for installation at altitudes no more than 1000m
above M.S.L. The surrounding humidity should less than 50% at 40℃ . It can be stored or
transported under ambient temperatures between -25℃ and 55℃ .
SPECIFICATIONS
Model Number
HYLS7TE
Motor
2300W S6 40% IP54
Log Capacity
Diameter *
5 ~ 320 mm
Length
520 mm
Splitting Force
7 t
Hydraulic Pressure
16 Mpa
Hydraulic Oil Capacity
6.5 L
Overall Size
Length
1060 mm
Width
278 mm
Height
522 mm
Weight
74 kg
* The diameter of the log is indicative - a small log can be difficult to split when it has knobs
or a particularly tough fiber. On the other hand, it may not be difficult to split logs with
regular fibers even if its diameter exceeds the max. figure indicated above.
ELECTRICAL REQUIREMENTS
Connect the main leads to a standard 230V±10% (50Hz±1Hz) electrical supply which has
protection devices of under-voltage, over-voltage, over-current as well as a residual current
device (RCD) which maximum residual current rated at 0.03A.

6
SET UP AND PREPARATION FOR OPERATION
1.Bolt the Support Leg to the Log Splitter, lift the log splitter by the handles at both ends and
place it on a 60-75cm high, stable, at and level work surface.
2.Familiarize yourself with the controls and features of this log splitter in the illustrations.
Before operating the log splitter, the Bleed Screw should be loosened by some rotations
until air can go in and out of the oil tank smoothly.
Air flow thru the Bleed Screw hole should be detectable during the log splitter is under
operations.
Before moving the log splitter, make sure the Bleed Screw is tightened to avoid oil leaking
from this point.
1. Log Pusher
2. Work Table
3. Wedge
4. Lift Handle
5. Support Leg
6. Log Retaining Plates
7. Switch
8. Motor
9. Pushbutton Box
10.Wheels for Minor Moving ONLY.
11.Hydraulic Control Lever
12.Control Lever Guard
13.Bleed Screw
14.Oil Drain Bolt w/ Dipstick
FAILED TO LOOSEN THE BLEED SCREW WILL KEEP THE
SEALED AIR IN HYDRAULIC SYSTEM BEING COMPRESSED
AFTER BEING DECOMPRESSED. SUCH CONTINUOUS AIR
COMPRESSION AND DECOMPRESSION WILL BLOW OUT THE
SEALS OF THE HYDRAULIC SYSTEM AND CAUSE PERMANT
DAMAGE TO THE LOG SPLITTER.
12
11
10
98
7
6
5
4
3
2
1
13
14
65575UK00M103.indd 6 2017/9/11 9:04:23

7
15.Max Pressure Limiting Screw
DO NOT ADJUST
THE MAX PRESSURE
LIMITING SCREW !
Max pressure was set before
the log splitter ex work and the
max pressure limiting screw is
sealed with glue to ensure the
log splitter works under pressure
no more than 7 tons. The setting
was done by qualied mechanic
with professional instruments.
Unauthorized resetting will cause
the hydraulic pump fail to output
enough splitting pressure or
RESULT IN SERIOUS INJURY
AS WELL AS DAMAGE TO THE
MACHINE .
PLUMBING DIAGRAMWIRING DIAGRAM
15
65575UK00M103.indd 7 2017/9/11 9:04:23

8
LOG SPLITTER OPERATION
This log splitter is equipped with"ZHB"control system that requires to be operated by both
hands of the user-Left hand controls the hydraulic control lever while right hand controls the
pushbutton switch. The log splitter will freeze upon absence of either hand. Only after both
hands release the controls, the log pusher starts to return backward to the starting position.
After this time interval, the oil under pressure will be overheated and the machine could
be damaged. For such extremely hard log, rotate it by 90o to see whether it can be split
in a different direction. In any case, if you are not able to split the log, this means that its
hardness exceeds the capacity of the machine and thus that log should be discarded to
protect the log splitter.
Never force the log splitter for more than 5 seconds by keeping pressure on it to
split excessively hard wood.
The splitting force and speed are governed by the 2-stage control lever.
Push the lever in the 1st stage about half way for faster speed at less
splitting force to split usual logs; Push the lever in the 2nd stage all way
for maximum splitting force at slower speed to split particularly hard
and seasoned logs. These stages can be shifted by simply raising and
lowering the lever.
65575UK00M103.indd 8 2017/9/11 9:04:24

9
65575UK00M103.indd 9
2017/9/11 9:04:25
Always set logs firmly on the log retaining
plates and work table. Make sure logs will
not twist, rock or slip while being split. Do
not force the blade by splitting the log on
the upper part. This will break the blade or
damage the machine.
Break log in the direction of its growing grain. Do not place log across the log splitter for
splitting. It may be dangerous and may seriously damage the machine.
Do not attempt to split 2 pieces of logs at the same time. One of them may fly up and hit
you.
FREEING A JAMMED LOG
·Release both controls.
·After the log pusher moves back and
completely stops at its starting position,
insert a wedge wood under the jammed
log.
·Start the log splitter to push the wedge
wood to go completely under the
jammed one.
·Repeat above procedure with sharper
slope wedge woods until the log is
completely freed.
Do not try to knock the jammed log off.
Knocking about will damage the machine
or may launch the log and cause accident.

10
65575UK00M103.indd 10
2017/9/11 9:04:25
REPLACING HYDRAULIC OIL
Replace the Hydraulic oil in the log splitter after
every 400 hours of use. Take following steps to
replace it.
·Make sure all moving parts stops and the log
splitter is unplugged.
·Unscrew Oil Drain Bolt with Dipstick to remove
it.
·Turn the log splitter on the Support Leg side
over an 8 liters capacity container to drain the
hydraulic oil off.
·Turn the log splitter on the the motor side.
·Refill fresh hydraulic oil at the volume as per
the hydraulic oil capacity of a particular model
indicated in above specifications table.
·Clean the surface of Dipstick on the Oil Drain
Bolt and put it back into the oil tank while keep
the log splitter vertically.
·Make sure the level of the refilled oil is just
between 2 grooves around the Dipstick.
·Clean the Oil Drain Bolt before thread them
back. Make sure they are tightened to avoid
leakage before place the log splitter horizontally.
Periodically check oil level to ensure it is
between 2 grooves around the Dipstick. Upon
Lower oil level, oil refilling is required.
Following hydraulic oils or equivalent are recommend for the log splitter's hydraulic
transmission system:
SHELL Tellus 22
MOBIL DTE 11
ARAL Vitam GF 22
BP Energol HLP-HM 22
SHARPENING WEDGE
After using the log splitters for some time, sharpen the wedge of the log splitter using a fine-
toothed file and smooth any burrs or crushed area along the cutting edge.

11
65575UK00M103.indd 11
2017/9/11 9:04:25
TROUBLE SHOOTING
PROBLEM
PROBABLE CAUSE
REMEDY SUGGESTED
Fails to split logs
Log is improperly positioned
R e f e r t o " L o g S p l i t t e r
Operation"section for perfect log
loading.
The sizes or hardness of the log.
exceeds the capacity of the
machine
Reduce the log sizes before
splitting it on the log splitter.
Wedge cutting edge is blunt
Refer to" Sharpening Wedge
"section to sharpen the cutting
edge.
Oil leaks
Locate leak(s) and contact the
dealer.
Unauthorized adjustment was
made on Max. Pressure Limiting
Screw. Lower max pressure rating
was set.
Contact the dealer.
The log pusher
moves jerkily,
taking unfamiliar
noise or vibrating
a lot
Lack of hydraulic oil and excessive
air in the hydraulic system.
Check oil level for possible oil
refilling.
Contact the dealer.
Oil leaks around
cylinder ram or
from other points.
Air sealed in hydraulic system
while operating.
Loosen Bleed Screw by some
rotations before operating the log
splitter.
Bleed Screw is not tightened
before moving the log splitter.
Tighten the Bleed Screw up before
moving the log splitter.
Oil Drain Bolt with Dipstick is
not tight.
Tighten the Oil Drain Bolt with
Dipstick.
Hydraulic Control Valve Assembly
and / or seal(s) worn
Contact the dealer

12
PARTS SCHEMATIC
65575UK00M103.indd 12 2017/9/11 9:04:26

2017/9/11 9:04:22
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING MACHINE
MODEL NUMBER : F071
SERIAL NUMBER :
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Save This Manual for Future Reference
65575UK00M103.indd 1
7 TON LOG SPLITTER
- Owner's Manual
Licensed by Hyundai Corporation, Korea

2017/9/11 9:04:22
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING MACHINE
MODEL NUMBER : F071
SERIAL NUMBER :
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Save This Manual for Future Reference
65575UK00M103.indd 1
7 TON LOG SPLITTER
- Owner's Manual
Licensed by Hyundai Corporation, Korea

2017/9/11 9:04:22
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING MACHINE
MODEL NUMBER : F071
SERIAL NUMBER :
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Save This Manual for Future Reference
65575UK00M103.indd 1
7 TON LOG SPLITTER
- Owner's Manual
Licensed by Hyundai Corporation, Korea

2017/9/11 9:04:22
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING MACHINE
MODEL NUMBER : F071
SERIAL NUMBER :
Both model number and serial number may be found on the main label.
You should record both of them in a safe place for future use.
Save This Manual for Future Reference
65575UK00M103.indd 1
7 TON LOG SPLITTER
- Owner's Manual
For Inquires, Please Contact:
Trade Tested Limited
PO Box 9117, Newmarket, Auckland 1149, New Zealand
0800 800 880
[email protected]
www.tradetested.co.nz
Licensed by Hyundai Corporation, Korea
Imported/Distributed by Trade Tested Limited