Woodstock Chimes ENCORE WATER BELL FOUNTAIN User manual

ENCORE WATER BELL FOUNTAIN™
by Woodstock Chimes®
ASSEMBLY INSTRUCTIONS
Water bubbles up through a center cluster of brass bells, while two floating bells
softly chime against the others as they swirl around the fountain.
Perfect for the home or garden
Thank you for purchasing the Encore Water Bell Fountain. This fountain is designed to combine the
relaxing sounds of flowing water with the peaceful chiming of brass bells. This effect is created by two
floating bells, which softly chime against a center cluster of stationary bells as they are swept around the
fountain by an underwater current created by the pump.
PARTS LIST
When you unpack your fountain you should find:
Bowl with Pump attached
The Bell Assembly, made up of six bells mounted on a plastic base (only two bells shown)
Flow Diverter
Output Hose
Fountainhead
Two floating bells (brass bells mounted to foam floats - not shown)
1326-instructions.qxd 7/13/04 10:21 AM Page 1

Woodstock Percussion, Inc.
Shokan, NY 12481-5124 USA
800-422-4463 • 800-4-A-CHIME • Fax: [phone] • E-mail: woodsto[email protected]om • www.chimes.com
©2003 WPI1326 - 12/03
FOUNTAIN ASSEMBLY
Step 1: Insert the large end of the flow diverter up through the hole in the center of the bell assembly. Insert
the fountainhead into this end of the flow diverter.
Step 2: Attach the output hose to the side of the flow diverter and anchor the end of the hose to the bottom of
the bowl by attaching it to the hose clip as shown.
Step 3: Insert the bottom end of the flow diverter into the hole at the top of the pump. Place the bell assembly
so that each leg is resting in one of the raised circles at the bottom of the bowl. The end of the output hose
should be oriented so that the water will flow in a clockwise direction around the bowl.
Step 4: Tuck the power cord into the notch on the underside of the bowl and place the fountain on a level
surface. Using distilled water (highly recommended), fill the bowl approximately 3/4 full or so that the water
level is about one inch below the rim of the bowl. Add the two floating bells, taking care that they are level
when placed in the water (otherwise they may tip over). Add water until the rims of the floating bells are even
with the rims of the six fixed bells. The fountain will not function properly with too little water, and the pump
should never be allowed to run dry.
Step 5: Now you are ready to plug in your fountain. Be sure that the power cord loops below the electrical
outlet to form a “drip loop.” In the event of a leak or spill this will prevent water from running down the cord
into the electrical outlet.
You can adjust the speed of the floating bells by turning the flow control on the side of the pump.
MAINTENANCE AND USE
1. Adding water: When adding water, always use clean distilled water. Using distilled water is highly recom-
mended to reduce mineral build-up and extend the life of the pump. Your fountain should be checked for
water level at least once every 2 to 3 days during continuous operation.
2. Continuous operation:The pump is designed to operate continuously for extended periods. In order to
ensure long pump life, it is recommended that you clean the fountain and pump, approximately every 2 to 3
months of operation.
3. Operating temperature: Do not operate fountain with water above 30° C (89° F). Also, do not expose to
temperatures below freezing. This could damage both the pump and bowl.
The Encore Water Bell Fountain is adapted from an original copyrighted design by artist/musician Ron Snider.
1326-instructions.qxd 7/13/04 10:21 AM Page 2

PRODUCT MAINTENANCE
Every part of a Woodstock Chime is weather protected. Over time, however, those layers of
protection can begin to wear. To enjoy your Woodstock Chime for years to come, we suggest you
hang it in an area that is not exposed to long term direct sunlight and periodically clean it with a damp
cloth and mild detergent. In addition, here are some simple maintenance tips:
Aluminum Tubes
Woodstock Chimes tubes are made of aluminum that will not rust when exposed to the elements.
However, over time, the aluminum may show pitting as a result of environmental factors. Please note
this will not affect the beautiful tones of your chimes. If necessary, use mild soap and water (or a
foaming, non-abrasive cleanser) to clean the tubes.
Wood Parts
Periodically, apply a thin layer of exterior use Danish or lemon oil with a clean cloth to the wood
parts. Regular oiling will help protect the wood and retard the natural aging process.
Rainbow Makers and Crystal Accents
Spray window cleaner on a clean, soft cloth and gently wipe crystals till they are clean and shiny.
Bamboo Chimes
•Hang your chime in an area protected from direct sunlight or heavy winds. Excellent locations
include under a porch overhang or in a shady tree.
•Bring your chimes in during extreme weather or windstorms.
•If you live in the north, bring your chimes in during the harsh winter months and store it in an
unheated area, such as a shed or garage.
•Occasionally wipe off your chimes with a damp cloth to remove any build-up or mold.
•Every spring, provide added weather protection by applying a coat of varnish on your chime
(you’ll want to wipe off the chime before doing this!)
We sincerely hope you enjoy your Woodstock Chime for many years to come.