Worldlawn WY28X User manual

3
R
WY28X WY32X
Commercial Mower
Operator’s Manual
Worldlawn Power Equipment, Inc.
401 N. Commerce Street, Beatrice, NE 68310
Toll Free Number: 1-800-267-4255

OPERATOR’S MANUAL
This manual contains assembly, operating, maintenance, adjustment, and safety instructions for your
WY28X/WY32X lawnmower. Before operating your mower, read this manual in its entirety carefully. By
following the operating, maintenance, adjustment, and safety instructions, you will prolong the life of your mower,
maintain its maximum efficiency, and promote safe operation..
If this Operator’s Manual becomes lost, damaged, or illegible, please replace it immediately: replacements may be
downloaded from our website: www.worldlawn.com.
POTENTIAL HAZARD
⚫This product is a piece of power equipment.
WHAT CAN HAPPEN
⚫Failure to follow safe operating practices can result in serious operator injury or even death.
HOW TO AVOID THE HAZARD
⚫Keep all shields, guards, and safety devices (especially the grass discharge system) in place
and in proper working condition.
⚫Stop machine and wait for all moving parts to stop, remove spark plug wires or remove key
before adjusting, servicing, or performing maintenance.
⚫If mower deck becomes clogged, stop machine and wait for all moving parts to stop. Remove
spark plug wire or remove key before cleaning blockage.
⚫Keep hands, feet, and clothing away from power driven parts.
⚫Keep others off mower.
POTENTIAL HAZARD
⚫Gasoline is harmful or fatal if swallowed. Long-term exposures to vapors have been known
to cause cancer in laboratory animals.
WHAT CAN HAPPEN
⚫Failure to use caution may cause serious injury or illness.
HOW TO AVOID THE HAZARD
⚫Avoid prolonged breathing of vapors.
⚫Keep face away from nozzle and gas tank opening.
⚫Keep away from eyes and skin.
⚫Never siphon by mouth.

TABLE OF CONTENTS
1. SAFETY………………………………………………………………………………………………
1
1.1 SafetyAlert Symbol…………………………………………………………………………………
1
1.2 Training………………………………………………………………………………………………
1
1.3 Preparation……………………………………………………………………………………………
1
1.4 Operation……………………………………………………………………………………………
3
1.5 Maintenance & Storage………………………………………………………………………………
4
1.6 Safety Decals…………………………………………………………………………………………
5
2. SPECIFICATIONS…………………………………………………………………………………..
6
2.1 Model Number………………………………………………………………………………………
6
2.2 Engine………………………………………………………………………………………………
6
2.3 Frame Assembly ……………………………………………………………………………………
6
2.4 Drive System ………………………………………………………………………………………
6
2.5 Cutting Deck …………………………………………………………………………………………
6
2.6 Operator Controls……………………………………………………………………………………
6
2.7 Accessories…………………………………………………………………………………………
7
2.8 Approximate Dimensions……………………………………………………………………………
7
2.9 Torque Requirements…………………………………………………………………………………
7
3. ASSEMBLY INSTRUCTIONS …………………………………………………………………….
8
3.1 Unpacking……………………………………………………………………………………………
8
3.2 Assembling………………………………………………………………………………………......
8
3.3 Engine maintenance………………………………………………………………………………….
8
4. OPERATION INSTRUCTIONS……………………………………………………………………
8
4.1 Pre-start………………………………………………………………………………………………
8
4.2 Starting Engine………………………………………………………………………………………
9
4.3 Mowing Operation …………………………………………………………………………………
9
4.4 Driving Operation………………………………………………………………………………….
9
4.5 Stopping Engine……………………………………………………………………………………
9
5. MAINTENANCE &ADJUSTMENTS……………………………………………………………
10
5.1 Periodic Maintenance………………………………………………………………………………
10
5.1.1Check the Engine Oil Level…………………………………………………………………………
10
5.1.2 Clean EngineAir Cooling System…………………………………………………………………
10
5.1.3 Clean Grass Build-up from Under Deck …………………………………………………………
10

5.1.4 Check Mower Blades………………………………………………………………………………
10
5.1.5 Check Safety Interlock system……………………………………………………………………..
11
5.1.6 Check For Loose Hardware………………………………………………………………………..
11
5.1.7 Check theAir cleaner………………………………………………………………………………
11
5.1.8 Change Engine Oil…………………………………………………………………………………
11
5.1.9 Check Tire Pressure………………………………………………………………………………..
12
5.1.10 Check Condition of Belts…………………………………………………………………………
12
5.1.11 Lubricate Grease Fittings…………………………………………………………………………
12
5.2 Adjustments………………………………………………………………………………………….
12
5.2.1 Cutting Height Adjustment ………………………………………………………………………
12
5.2.2 Blade Drive Belt Adjustment and Replacement…………………………………………………..
12
5.2.2.1 Synchronous BeltAdjustment and Replacement………………………………………………..
13
5.2.2.2 Blade Brake Pad Replacement…………………………………………………………………...
13
5.2.3 Transmission Drive Belt Adjustment…………..…………………………………………………..
13
5.2.4 Drive Control Adjustment…………………………………………………………………………
13
5.2.5 Drive Belt Adjustment and Replacement………………………………………………………….
14
5.2.6 Transmission Replacement…………………………………………………………………………
14
5.2.7 Shift Control RodAdjustment……………………………………………………………………..
14
5.2.8 Blade Control RodAdjustment…………………………………………………………………….
5.
15
6. TROUBLESHOOTING ……………………………………………………………………………
15
7. BATTERY MAINTENANCE……………………………………………………………………....
16
8. WIRING DIAGRAM………………………………………………………………………………...
18
9. LIMITED WARRANTY…………………………………………………………………………….
19

1
SAFETY
1.1 SAFETYALERT SYMBOL
This SAFETY ALERT SYMBOL is used both
in this manual and on the machine to identify
important safety messages which must be followed to
avoid accidents. This symbol means:
ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED!
The safety alert symbol above alerts you to
unsafe actions or situations by the word
DANGER, WARNING, or CAUTION.
Failure to observe the safety instructions could result
in death or serious injury.
Failure to observe the safety instructions could result
in death or serious injury.
Failure to observe the safety instructions may result in
slight or serious injury.
1.2 TRAINING
1.2.1 Regard the mower as a piece of power
equipment. The operator needs to be trained before
operating this unit.
1.2.2 Read the instructions carefully. Be
thoroughly familiar with controls and the
proper use of the equipment.
1.2.3 Never allow operation of the equipment
without proper instruction.
1.2.4 Keep everyone, especially children and pets,
away from the area of operation. Remember that the
operator or user is responsible for accidents or
hazards occurring to other people or their property.
1.3 PREPARATION
1.3.1 Evaluate the terrain to determine what
accessories and attachments are needed to properly
and safely perform the job. Only use accessories and
attachments approved by
Worldlawn Power Equipment, Inc.
1.3.2 The use of personal protective equipment,
such as (but not limited to) protection for the eyes,
ears, feet, and head is recommended.
POTENTIAL HAZARD
· This machine produces sound levels in excess of
85dBA at the operator’s ear when in operation.
WHAT CAN HAPPEN
· Exposure to sound levels of 85dBA or above for
extended periods of time can cause hearing loss.
HOW TOAVOID THE HAZARD
· Wear hearing protection when operating this
machine.
1.3.3 While mowing, always wear ample
footwear and long trousers. Do not operate equipment
when barefoot or when wearing open sandals.
1.3.4 Thoroughly inspect the area where the
equipment is to be used and remove all stones, sticks,
wires, bones, and other foreign objects which may
damage the equipment or cause personal injury to
operator or bystanders.
POTENTIAL HAZARD
· Engine exhaust contains carbon monoxide, which
is an odorless deadly poison.
WHAT CAN HAPPEN
· Carbon monoxide can kill you.
HOW TO AVOID THE HAZARD
· Do not run engine indoors or in a small confined
area where dangerous carbon monoxide fumes can
collect.

2
POTENTIAL HAZARD
· In certain conditions gasoline is extremely
flammable and highly explosive.
WHAT CAN HAPPEN
· A fire or explosion from gasoline can burn you,
others, and cause property damage.
HOW TO AVOID THE HAZARD
· Do not smoke while refueling, and stay away
from an open flame or where gasoline fumes may
be ignited by a spark.
· Refuel only outdoors.
· Store gasoline in an approved container and keep
it out of the reach of children.
· Add fuel before starting the engine. Never remove
the cap of the fuel tank or add fuel when engine is
running or when the engine is hot.
· Never fill the fuel tank so that gasoline level rises
above a level that is 3/8"(10mm) below the
bottom of the filler neck to allow for gasoline
expansion and prevent fuel spillage.
· If fuel is spilled, DO NOT attempt to start the
engine. Move away from the area of the spill and
avoid creating any source of ignition of the fuel
until vapors have dissipated.
· Do not operate without entire exhaust system in
place and in proper working condition.
POTENTIAL HAZARD
· In certain conditions gasoline is extremely
flammable and highly explosive.
WHAT CAN HAPPEN
· A static charge can ignite gasoline vapors. A fire
or explosion from gasoline can burn you, others,
and cause property damage.
HOW TO AVOID THE HAZARD
· Purchase and store gasoline only in an approved
container.
· Always place gasoline containers on the ground
away from your vehicle while filling.
· Do not fill gasoline containers inside a vehicle or
on a truck or trailer bed, because interior carpets
or plastic truck bed liners may insulate the
container and slow the loss of any static charge.
· When practical, remove gas-powered equipment
from the truck or trailer and refuel the equipment
with its wheels on the ground.
· If this is not possible, then refuel such equipment
on a truck or trailer from a portable container,
rather than from a gasoline dispenser nozzle.
· If a gasoline dispenser nozzle must be used, keep
the nozzle in contact with rim of the fuel tank or
container opening at all times until fueling is
complete.
POTENTIAL HAZARD
· Gasoline vapor can collect inside enclosed trailers
and may be ignited by electrical sparks or hot
engine/exhaust components.
WHAT CAN HAPPEN
· Explosion and fire may occur, resulting in
property damage, personal injury, and/or death.
HOW TO AVOID THE HAZARD
· Provide adequate ventilation of any enclosed
trailer to prevent build up of gasoline vapors,
especially at floor level.
· Refuel only outdoors, never inside an enclosed
trailer.
· Be sure all fuel tanks and gasoline storage
containers have proper caps installed to prevent
spillage and minimize vapor escaping into the
trailer.
· Do not place any equipment that is leaking
gasoline into an enclosed trailer.

3
1.4 OPERATION
Although hazard control and accident prevention
partially are dependent upon the design and
configuration of the equipment, these factors are also
dependent upon the awareness, concern, prudence,
and proper training of the personnel involved in the
operation, transport, maintenance, and the storage of
the equipment. It is essential that all Operator Safety
Mechanisms be connected and in operating condition
prior to use for mowing.
POTENTAL HAZARD
· Operating engine parts, especially the muffler,
become extremely hot.
WHAT CAN HAPPEN
· Severe burns can occur on contact.
· Debris, such as leaves, grass, brush, etc. can catch
fire.
HOW TO AVOID THE HAZARD
· Allow engine parts, especially the muffler, to cool
before touching.
· Remove accumulated debris from muffler and
engine area.
· Install and maintain a spark arrester in working order
before using equipment on forest-covered,
grass-covered, or brush-covered unimproved land.
POTENTIAL HAZARD
· Hands, feet, hair, clothing, or accessories can
become entangled in rotating parts.
WHAT CAN HAPPEN
· Contact with rotating parts can cause traumatic
amputation or severe lacerations.
HOW TO AVOID THE HAZARD
· Do not operate the machine without guards, shields,
and safety devices in place and working properly.
· Keep hands, feet, hair, jewelry, or clothing away
from rotating parts.
1.4.1 Give complete, undivided attention to the job at
hand.
1.4.2 Mow only in daylight or good artificial light;
keep away from holes and hidden hazards. NEVER
carry passengers. DO NOT operate the mower when
children or others are in the area!
1.4.3 When feasible, avoid operating the equipment in
wet grass.
1.4.4 Use extreme caution when mowing and/or
turning on slopes as loss of traction and/or tip-over
could occur. The operator is responsible for safe
operation on slopes.
POTENTIAL HAZARD
· Mowing on wet grass or steep slopes can cause
sliding and loss of control.
WHAT CAN HAPPEN
· Wheels dropping over edges, ditches, steep banks,
or water can cause rollovers, which may result in
serious injury, death, or drowning.
HOW TO AVOID THE HAZARD
· Do not mow on slopes when grass is wet.
· Do not mow near drop-offs or near water.
· Do not mow on slopes greater than 15 degrees.
· Reduce speed and use extreme caution on slopes.
· Avoid sudden turns or rapid speed changes.
⚫Use a hand trimmer only near drop-offs, ditches,
steep banks, or water. This area can be dangerous,
see Figure 1.
⚫Progressively greater care is needed as the slope
increases.
⚫Always avoid sudden starting or stopping on a
slope. If tires lose traction, disengage the blades
and proceed slowly off the slope.
⚫Avoid sudden starts when mowing uphill. Mower
may tip backwards.
⚫Be aware that loss of traction may occur going
downhill. Weight transfer to the front wheels may
cause drive wheels to slip and cause loss of
braking and steering.

4
⚫Watch for ditches, holes, rocks, dips, and rises
that change the operating angle, as rough terrain
could overturn the machine.
⚫Use extreme care with grass catchers or
attachments. These can change the stability of the
machine and cause loss of control.
1.4.5 Stop the blades when transporting the mower to
and from the area to be mowed.
1.4.6 Never operate the mower with defective guards,
shields, or covers. Always have safety shields, guards,
switches, and other devices in place and in proper
working condition.
1.4.7 DO NOT change the engine governor setting or
overspend the engine. Operating an engine at
excessive speed may increase the hazard of personal
injury.
1.4.8 Disengage PTO before starting engine.
1.4.9 Start the engine carefully with feet well away
from the blades.
1.4.10 Keep hands, feet, and clothing away from
rotating parts while the mower is being operated.
1.4.11 Stop engine, wait for all mowing parts to stop,
and remove key:
⚫Before checking, cleaning, or working on the
mower.
⚫After striking a foreign object (inspect mower for
damage and make repairs before restarting and
operating the mower).
⚫Before clearing blockages.
⚫Whenever you leave the mower.
Stop the engine and wait for all moving parts to stop:
⚫Before refueling.
⚫Before dumping the grass catcher.
1.4.12 The fuel system is provided with a shut-off
valve. CLOSE VALVE:
⚫When the machine will not be used for a few
days.
⚫During transport to and from the job.
⚫When parked inside a building.
1.4.13 This mower was designed for one operator only.
Keep all others away from mower during operation.
1.4.14 DO NOT mow with the discharge deflector
raised, removed, or altered unless there is a grass
collection system or mulch kit in place and working
properly.
1.4.15 Be aware of the mower discharge and direct
discharge away from others.
1.4.16 DO NOT operate the mower under the
influence of alcohol and/or drugs.
1.4.17 Use extra care when approaching blind corners,
shrubs, trees, or other objects that may obscure vision.
1.5 MAINTENANCE AND STORAGE
1.5.1 For engine maintenance, follow the engine
manufacturer’s recommendations precisely as stated
in the engine manual.
1.5.2 Keep engine and engine-area, free from
accumulation of grass, leaves, excessive grease or oil
and other debris, which can accumulate in these areas.
These materials can become combustible and may
result in a fire.
1.5.3 Store fuel in a container specifically designed
for this purpose and in a cool, dry place.
1.5.4 Keep the mower and fuel container in locked
storage to prevent children from playing or tampering
with them.
1.5.5 Gasoline powered equipment or fuel containers
should not be stored in a basement or any enclosed
area where open pilot lights or heat appliances are
present.
1.5.6 Maximum mowing results and safety can only
be achieved if the mower is properly maintained and
operated correctly.
1.5.7 Check all bolts frequently to maintain proper
tightness.
1.5.8 Keep all guards, shields, and safety devices in
place and in safe working condition.
1.5.9 Frequently check for worn or deteriorating
components that could create a hazard.
1.5.10 All replacement parts must be the same as or
equivalent to the parts supplied on the original
equipment.

5
1.6 SAFETY DECALS
1.6.1 Keep all safety decals legible. Remove all grease,
dirt, and debris from safety decals and instructional
labels.
1.6.2 Safety decals must be replaced if they are
missing or illegible.
1.6.3 When new components are installed, be sure that
current safety decals are affixed to the replaced
components.
1.6.4 New safety decals may be obtained from your
authorized equipment dealer or distributor or from
Worldlawn Power Equipment, Inc.
1.6.5 Safety decals may be affixed by peeling off the
backing to expose the adhesive surface. Apply only to
clean, dry surface. Smooth to remove any air bubbles.
1.6.6 Familiarize yourself with the following safety
decals and instruction labels. They are critical to the
safe operation of your machine.
Decals and their locations are as follows:
1. On the left panel of rear frame
1. On the panel of console (Electric Start Model )
2. On the panel of mower deck
4. On the panel of mower deck
5. On the panel of mower deck and guard plate of
LH&RH belt shield
6. In front of the console plate
7. On the panel of rear frame
8. On the panel of mower deck

6
9. On the Deck Cover
10. On the panel of console (Recoil model)
11. On the left side of front frame
12. On the right side of front frame
13. On the front of the mower deck
2. SPECIFICATIONS
2.1 Model Number:
WY28X11BS、WY28X11BSE、WY32X11BS、
WY32X11BSE、WY32X11HD、WY32X11HDE
2.2 Engine:
MODEL
ENGINE
STARTER
WY28X11BS
B＆S10.5HP Intek I\C
Recoil
WY28X11BSE
B＆S10.5HP Intek I\C
Electric
WY32X11BS
B＆S10.5HP Intek I\C
Recoil
WY32X11BSE
B＆S10.5HP Intek I\C
Electric
WY32X11HD
GXV340
Recoil
WY32X11HDE
GXV390
Electric
2.3 FrameAssembly
⚫Front Frame: Rectangle tube 40×30×2.5(mm)
⚫Thickness (Steel plate of engine frame): 3mm
⚫Fuel Tank: 2 gallon (7.6 liter) plastic fuel tank
⚫Drive Wheel: 13×5" two-ply pneumatic
tubeless.
⚫Caster Wheel: 8×3", smooth, pneumatic
tubeless.
2.4 Drive System
⚫Type: Belt drive with twin power belts for
increased friction to pulley surface.
⚫Transmissions: 3-speed transmission
⚫Steering/Travel Control: Clutch/brake fingertip
steering, key lock switch.
⚫Brakes: band brake, one on each wheel.
⚫Safety Group: Hand actuated operator presence
system with blade clutch and transmission
interlock to engine kills.
⚫Forward Speed Range: 0-4.38mph(0-7km/h)
2.5 Cutting Deck
⚫Type: Floating deck
⚫True Cutting Width: 28"（71.1cm）/32" (81.26cm)
⚫Blade engagement: Manual control
⚫Cutting Height Adjustment: Manual adjustment
1.5″ (3.8cm) to 4.0″ (10.16cm) in 0.5″ (1.27cm)
increments.
⚫Cutting Blades: 0.2"(5mm)thick, (2) 28” cut
14.5″(36.8cm); (2) 32” cut 16.5” (41.9cm).
⚫Cutting Deck Belts: Flat Belt.
⚫Synchronous Belt: 28” -1072-8M/32”-1200-8M
2.6 Operator Controls (See FIG 1)
⚫Key switch: Located on the control panel (some
recoil starter models are not equipped with key
switch). Recoil starter has two positions. Turning
to "on" allows the engine to run; turning to "off"
stops the engine. Electronic start model has three
positions. When starting, turn to "start" position;
then remove your hand.
⚫Throttle Control: Located on the control panel.
Throttle is used to control engine speed. Moving
throttle lever forward will increase engine speed

7
and moving throttle lever to the rear will
decrease engine speed. Some recoil starter
models are not equipped with key switch. Move
the throttle lever to the rearmost position, then
the engine will kill.
⚫Blade Drive Lever: Push the mower blade drive
lever forward to the engage position. Pull the
mower blade drive lever backward to the
disengage position to stop the blades.
⚫Hand actuated operator presence lever: When in
normal operation, hold the operator presence
lever down. When released, engine will kill.
⚫Steering Brake Levers: While squeezing the
steering lever handles with both hands, release
right and left neutral latches; then release right
and left steering levers to move forward. When
the steering levers are released, the mower will
travel straight forward. To make a right turn,
squeeze the RH steering lever. To turn left,
squeeze the LH steering lever. Squeeze both
steering levers, lock right and left neutral latches,
and the mower will stop.
⚫Neutral Latches: Located on bottom of the
handles. They are used to lock the steering levers
when stopping.
⚫Gear shift lever: Used to shift the transmission
from neutral into one of 3 forward gears.
⚫Fuel shut-off valve: The fuel shut-off valve is
used to shut off the fuel when the machine will
not be used for a few days, during transport to
and from the jobsite, and when parked inside a
building.
2.7Accessories:
a) Grass catcher assembly (2832200): 80L, see FIG 2
b) Mulching Assembly (2832010/3210135): See FIG
3
FIG 2
FIG 3
2.8Approximate Dimensions:
2.8.1 Width:
Model
Without
Deck
Discharge
chute up
Discharge
chute down
WY32
28inch
71.1cm
32.8 inch
83.4cm
41.3 inch
104.9 cm
WY28
27.8 inch
70.5cm
28.8 inch
73.2cm
37.8 inch
96 cm
2.8.2 Overall Length: 67.3in（171.0cm）
2.8.3 Overall Height: 42.9in (109.0cm)
2.8.4 Tread:
⚫Drive Wheel Tread: 22.6in（57.6cm）
⚫Caster Wheel Tread: 20.6in（52.3cm）
2.8.5 Wheelbase:
⚫31.9in（81cm）
2.8.6 WY28 Net Weight: 283lbs（129Kg）
WY32 Net Weight: 305lbs（139Kg）
2.9 Torque Requirements
⚫Cutter Housing Spindle Nut: 66± 13ft-lb
(90±18N-m)
⚫Engine Deck/Front Frame Mounting Bolts:

8
40-52ft-lb (55-70 N-m)
3.ASSEMBLY INSTRUCTIONS
3.1 Unpacking
Open the crate. Remove the loose parts (i.e.,
operator’s manual, etc) from crate. Remove unit from
crate; check there are no loose parts left.
3.2 Assembling Instructions
⚫Unfold the handle, and fix the handle with four
M10×25 Flange Hd. Bolts and four M10 locknuts
on each side as shown in FIG 4.
⚫All of the control rods, (left and right drive, blade
control and speed selector) have a clevis that is
secured with a M8 x 16mm clevis pin, washer
and cotter pin.. See FIG 4
⚫The Throttle Cable must be attached to the
engine according to the Engine Operator's
Manual. The Fuel Tank Line connects to the line
of the engine. (The positions of Fuel Filter and
Throttle Cable Attachment are a bit different on
different models of Engines.) See FIG 5
FIG 5
3.3 Engine Maintenance
Engine is shipped without oil. Fill to the
appropriate level with SAE10W-30 or 10W-40.
4. OPERATION INSTRUCTIONS
Read these instructions carefully before operating
the mower.
4.1 Pre-start
⚫See Engine Owners Manual
⚫Check engine oil level.
⚫Fill fuel tanks. For best results use only clean,
fresh, regular grade, unleaded gasoline with an
octane rating of 87 or higher. Do not add oil to
gasoline. Do not overfill fuel tank.
⚫Open the fuel tank shut-off valve.
⚫Make sure you understand the controls, their
locations, their functions, their safety
requirements, and how to stop quickly.
POTENTIAL HAZARD
·The rotating blades under the mower deck are
dangerous.
WHAT CAN HAPPEN
·Blade contact can cause serious injury or kill you.
HOW TO AVOID THE HAZARD
·DO NOT put hands or feet under the mower or
mower deck when the blades are engaged.

9
⚫Refer to Maintenance, Section 5, and perform all
necessary inspection and maintenance steps.
⚫Check tire pressure in drive wheels. Proper
inflation pressure for tires is 30psi (210kpa).
⚫Check tire pressure in caster wheels. Proper
inflation pressure for tires is 30psi (210kpa).
4.2 Starting Engine
⚫Turn the key switch to the “ON” position. The
transmission must be in neutral, the blade drive
lever must be disengaged.
1）For recoil with key, turn the key switch to the
“ON” position, pull the cable to start the engine.
2）For recoil without key, intermittently pull the
cable to start the engine.
3）For electric start, turn the key switch to the
“Start” position to start the engine.
⚫On a cold engine, place the throttle midway
between the “SLOW″ and “FAST″ positions and
push choke lever forward to the “ON″ position.
Turn ignition switch to the “start″ position.
Release the switch as soon as the engine starts.
4.3 Mowing Operation
Push blade drive lever forward to engage blades.
Pull blade drive lever back to disengage blades. Be
sure that all persons are clear of mower deck and
discharge area before engaging PTO.
IMPORTANT: Set the throttle to “midway″ position.
Push blade drive lever to the “ROTATE″ position.
Speed up the throttle, begin to mow.
Stopping the blades: Set the throttle to the “midway″
position, pull the mower blade drive lever backward
to the “disengage” position to stop the
blades.
POTENTIAL HAZARD
·An uncovered discharge opening will allow objects
to be thrown in an operator’s or bystander’s direction.
Also, contact with the blade could occur.
WHAT CAN HAPPEN
·Thrown objects or blade contact can cause serious
injury or death.
HOW TO AVOID THE HAZARD
·Never operate the mower with the discharge
deflector raised, removed, or altered unless there is a
grass collection system or mulch kit in place and
working properly.
4.4 Driving Operation
Squeeze the right and left steering lever handle bars
and move neutral latches into the lock position.
Release handle bars and select speed by moving the
gear shift lever from the neutral position to the desired
speed.
Squeeze the right and left steering levers, release the
locks, and then release the steering levers to move
forward slowly. Squeeze the right steering lever to
turn right and the left steering lever to turn left.
4.5 Stopping engine
Pull the blade drive lever backward to the disengage
position to stop the blades. Squeeze the right and left
steering lever handle bars and move neutral latches
into the lock position. Rotate key switch to the “OFF″
position. Remove the key to prevent children or other
unauthorized persons from starting the engine. Close
fuel shut-off valve when the machine will not be used
for a few days, transporting, and when the unit is
parked inside a building.

10
5. MAINTENANCE&ADJUSTMENTS
POTENTIAL HAZARD
·While maintenance or adjustments are being made,
someone could start the engine.
WHAT CAN HAPPEN
·Accidental starting of the engine could seriously
injure you or other bystanders.
HOW TO AVOID THE HAZARD
·Remove the key from the ignition switch and pull
the wire off the spark plug before you do any
maintenance. Also push the wire aside so it does not
accidentally contact the spark plug.
POTENTIAL HAZARD
·The engine can become very hot.
WHAT CAN HAPPEN
·Touching a hot engine can cause severe burns.
HOW TO AVOID THE HAZARD
·Allow the engine to cool completely before
servicing or making repairs around the engine area.
5.1 PERIODIC MAINTENANCE
5.1.1 Check the engine oil level.
Service Interval: Daily
⚫Make sure unit is on a level surface. Stop engine,
wait for all moving parts to stop, remove key or
pull out spark plug lead.
⚫Check when engine is cold.
⚫Clean area around dipstick. Remove dipstick and
wipe oil off. Reinsert the dipstick. Do not screw
into place. Remove the dipstick and read the oil
level.
⚫If the oil level is low, add oil to bring the oil level
up to the "FULL" mark on the dipstick. Use oil
as specified in the Engine Owner’s Manual.
IMPORTANT: DO NOT operate the engine with the
oil level below the "LOW" or "ADD" mark on the
dipstick or over the "FULL" mark.
5.1.2 Clean EngineAir Cooling System.
Service Interval: Daily or more often in dry conditions
⚫Stop engine, wait for all moving parts to stop,
and remove the key.
⚫Clean all debris from rotating engine air intake
screen and from around engine shrouding.
POTENTIAL HAZARD
·Excessive debris can cause the engine and
hydraulic system to overheat.
WHAT CAN HAPPEN
·Excessive debris around the engine cooling air
intake and inside of the pump compartment can
create a fire hazard.
HOW TO AVOID THE HAZARD
·Clean all debris from around the engine and
hydraulic pumps daily.
a) Stop engine, wait for all moving parts to stop, and
remove the key.
b) Clean all debris from rotating engine air intake
screen and from around engine shrouding.
5.1.3 Clean grass build-up from under deck.
Service Interval: Daily
⚫Stop engine, wait for all moving parts to stop,
and remove key.
⚫Clean out any grass build-up from the underside
of deck and in discharge chute.
5.1.4 Check mower blades.
Service Interval: Daily
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Lift deck.
⚫Inspect blades and sharpen or replace as required.
⚫Re-install the blades (if they were removed) by
placing a block of wood between the front or rear
baffles and the blade; then torque the blade bolts
to 66±13ft-lb (90±18N-M). Be sure the spring
disk washer cone is installed toward the bolt head.
（See FIG 6）

11
FIG 6
POTENTIAL HAZARD
·Operating a mower deck with loose or weakened
blade bolts can be dangerous.
WHAT CAN HAPPEN
·A loose or weakened blade bolt could allow a blade
rotating at a high speed to come out from under the
deck, causing serious injury or property damage.
HOW TO AVOID THE HAZARD
·DO NOT lubricate the threads of the bolt or spindle
before assembly.
·Torque the blade bolt to 66±13ft-lb (90±18N-M).
·Stop engine, wait for all moving parts to stop, and
remove key or pull out spark plug lead before
removing blades.
5.1.5 Check safety interlock system.
Service Interval: Daily
Check starting circuit:
- Ignition switch must be in the “ON”or “START”
position.
- Transmission must be in neutral.
- Blade drive lever must be disengaged to start engine
with recoil starter.
Check engine "kill" (flameout) circuit:
Remove your hands from the Operator Presence
Control Lever when the engine is running and the
engine should stop running within 3 seconds.
NOTE: If machine does not pass any of these tests, do
not operate. Contact your authorized WORLDLAWN
POWER EQUIPMENT SERVICE DEALER. It is
essential that operator safety mechanisms be
connected and in proper operating condition prior to
use for mowing.
5.1.6 Check for loose hardware.
Service Interval: Daily
⚫Stop engine, wait for all moving parts to stop,
and remove key.
⚫Visually inspect machine for any loose hardware
or any other possible problem. Tighten hardware
or correct the problem before operating.
5.1.7 Check the air cleaner.
Service Interval: 50 hrs
Check more often under severe conditions. See engine
manual for additional information.
⚫Stop engine, wait for all moving parts to stop,
and remove the key.
⚫Loosen retaining clips and remove air cleaner
compartment cover.
⚫Remove paper element. Check the condition of
the paper element. Replace if dirty, bent or
damaged.
⚫Do NOT wash or use pressurized air to clean
paper element or inner element.
5.1.8 Change engine oil.
Service Interval: 100 hrs
NOTE: Change oil and filter after first five (5) hrs. of
operation.
⚫Stop engine, wait for all moving parts to stop,
and remove key.
⚫Drain oil while engine is warm from operation.
⚫Replace the oil filter every other oil change.
Clean around oil filter and unscrew filter to
remove. Before reinstalling new filter, apply a
thin coating of oil on the surface of the rubber
seal. Turn filter clockwise until rubber seal
contacts the filter adapter; then tighten filter an
additional 2/3 to 3/4 turn.
⚫Clean around oil fill cap and remove cap. Fill to
specified capacity and replace cap. Use oil

12
recommended in engine owner’s manual. DO
NOT overfill.
⚫Start the engine and check for leaks. Stop engine
and recheck oil level.
5.1.9 Check tire pressure:
Service Interval: 40hrs
Stop engine, wait for all moving parts to stop, and
remove key.
⚫Check tire pressure in drive tires.
⚫Inflate drive tires to 30psi (210kPa).
⚫Check tire pressure in caster tires.
⚫Inflate caster tires to 30PSI（210kPa）.
5.1.10 Check condition of belts:
Service Interval: 40hrs
⚫Stop engine, wait for all moving parts to stop,
and remove key.
⚫Check all the belts.
⚫Remove the left and right belt shields of deck and
lay them aside to inspect belts.
⚫See Sections 5.2.2, 5.2.2.1, and 5.2.3 for belt
adjustment.
5.1.11 Lubricate grease fittings:
⚫Service Interval: Refer to chart
Stop engine, wait for all moving parts to stop, and
remove key. See the FIG 7.
LUBRICATION CHART
FITTING
LOCATIONS
FITTING
TIMES
SERVICE
INTERVAL
1
1
50hrs
2
1
50hrs
FIG 7
5.2ADJUSTMENTS
IMPORTANT: Disengage PTO, shut off engine, wait
for all moving parts to stop, and remove key before
servicing, cleaning, or making adjustments to the unit.
5.2.1 Cutting Height Adjustment.
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Disengage Blade.
NOTE: When changing cutting height positions,
always come to a complete stop and disengage the
blade.
⚫Insert height adjustment pin into the hole
corresponding to desired cutting height. See
decal on deck lift plate. Move lever out of
transport position and down onto height
adjustment pin to mow at selected height. See
FIG 8.
FIG 8
5.2.2 Blade Drive Belt Adjustment and Replacement.
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Remove the belt cover. Adjust the mower deck
belt using a belt tension gauge. Engage the blade
drive lever, tension the mower belt, and adjust
the belt so that the belt moves 1/4″ with 10
pounds of pressure. Adjust the tension by
tightening or loosening the nut (Nut 1). (See FIG
9).
⚫Engage the blade drive lever，loosen the nut，
tension the waist-shaped hole forward. Make sure
the belt tightening is suitable. (Give the belt
tension side the force of 1-2KG, the belt

13
deflection is 7-9mm ) (See FIG 9)
5.2.2.1 Synchronous BeltAdjustment & Replacement
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Remove blade transmission belt according to
reference method 5.2.2, then loosen nut in the
idler pulley, take the synchronous belt from the
axis pin, then install the new synchronous belt in
reverse order. (See FIG9)
5.2.2.2 Blade Brake Pad Replacement
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Remove the belt cover, turn the shift arm, move
shift arm away from pulley, remove bolts and
nuts, replace with new brake pad, install bolts
and nuts, and make blade brake pad aim at the
belt pulley groove center, then screw down the
nut. Test blade brake system; blade brake pad can
make rapid rotary blades stop running in 3
seconds. (See FIG 9)
FIG 9
5.2.3 Transmission Drive BeltAdjustment.
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Transmission drive belt is on the underside of the
engine frame weldment. Adjust the belt so that
the belt moves 1/4″ with 10 pounds of pressure;
adjust the tension by moving transmission drive
idler pulley, then tighten all the nuts.(See FIG 10)
⚫Loosen the nut on the tension pulley of the
transmission drive belt. Remove the tension
pulley and the belt you need to replace. Install
the new belt, then install the transmission drive
pulley in reverse order. Adjust the belt according
to the method of belt adjustment, then tighten the
nut. (See FIG 11)
FIG 10
5.2.4 Drive Control Adjustments
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫The drive control is a system of interconnected
machine elements made up of steering and
braking functions, that is to say, one steering
lever applies to neutral latch lock position or
neutral latch unlock position. When two steering
levers are in neutral lock position, the power is
disengaged. To brake, adjust brake lever and
control rod beside the mower of the same
strength.
⚫Adjusting control rod: Remove hair pin on the
top of control rod, pull out the control rod from
steering lever, turn the control rod so that the
length of two control rods is the same and
reinstall all parts in proper order. (See FIG 12)

14
⚫Adjusting the brake force: Lift the left / right
shift rod and lock it by the buckle. Rotate nut 1
and nut 2 of the brake lever, so as to compress
the spring to get enough brake force. Then rotate
nut 1 again, ensure that 1mm gap is maintained
between nut 1 and the rod end connector.
(See FIG 11)
FIG 11
5.2.5 Drive belt replacement
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Remove bolt of the belt guard of drive belt.
Remove belt guard. Lift brake control rod to
loosen idler pulley. Remove the belt from the
large belt pulley and tire. Replace with new belt.
Reinstall all parts in reverse order.
FIG 12
5.2.6 Transmission case replacement
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫When replacing transmission case, remove the
two outer pulley guards; remove the wheel drive
belts; remove the wheel drive pulleys. Remove
the output shaft bearings (2). Remove the
transmission drive belt, drive pulley bolt
(3300198) and pulley. Remove the transmission
mounting bolts (3300106). Disconnect the shift
link. Transfer the shift link to new transmission.
Install new transmission case back into position.
Reinstall output shaft bearings; leave bolts loose.
Install and tighten case mounting bolts (3300106).
Reconnect shift link. Reinstall transmission belt
and pulley and tighten pulley bolt (3300198).
⚫Finally, tighten output shaft bearings, reinstall
wheel drive pulleys, belts and guards on each
side. (See FIG 13)
FIG 13
5.2.7 Shift Control Rod Adjustment
⚫Stop engine, wait for all moving parts to stop,
and remove key or pull out spark plug lead.
⚫Move Shift Control Rod into neutral position.
Handle should compress pressure switch button
completely, but not so far as to hit switch housing,
otherwise rod length should be adjusted. To