wowvision proVEOS Reference manual

Chapter 1 Introduction
1.1 Board and I/O Layout
Table 1.1 Board Components
Item
Item
01.
S-ATAII Connector x 2
13.
BIOS
02.
4-pin DC Power output Connector
14.
Front Panel Connector
03.
Front Audio Connector
15.
JP14 CMOS clear jumper
04.
Intel ICH9M
16.
USB2.0 Connectors
05.
IEEE 1394 Connector
17.
Mini Card Connector
06.
COM1
18.
24bits LVDS Connector(Option)
07.
Mini Card Connector
19.
LVDS_INV Connector(Option)
08.
Battery
20.
Intel GM45
09.
S-ATAII Connector
21.
200-pin SO-DIMM x 2,Support DDRII
667/800MHz
10.
SYSTEM Fan Connector
22.
Socket P support Intel Penryn Qual
Core/Dual Core/Celeron CPU
11. TV-Out Connector (Option)
23.
Stand_by LED
12.
CPU Fan Connector

1.2 Rear I/O Ports
Figure 1.1 Board I/O Layout
12 11
10
9
8
1
23456 7
Table 1.2: Real I/O
Item
Item
01.
19V DC Adapter Connector
07.
MIC In
02.
DVI Port
08.
Center/Subwoofer
03.
HDMI Port
09.
Speaker Out
04.
E-SATA Port
10.
Rear SUR(S/PDIF_Out)
05.
USB2.0 Port x 4
11. Line In(S/PDIF_In)
06.
Side SUR
12.
RJ45 Lan Port

Table 1.3: proVEOS Specifications
Model
proVEOS
CPU
Socket P Intel® Penryn / Qual Core / Dual Core / Celeron
(FSB 800/1066 MHz)
Chipset
Intel® GM45 / ICH9M
Main Memory
Dual Channel Mode
Support SO-DIMM DDRII 667/800 MHz
DDRII SO-DIMM x 2
DIMM Type : 256/512MB/1GB/2GB
Max Memory : 4GB
Graphics
Integrated Intel® GFX 500 (Graphics Media Accelerator) in Chipset
Storage
Integrated Serial ATA Controller
LAN
Integrated Intel Gigabit PCI LAN Controller
Sound
Intel High Definition Audio on-board Support 7.1 Channel and above
USB
Integrated in Chipset, USB 2.0 x 8
Slots
Mini Card x 2
Back Panel I/O
Power DC-in Jack(support 19V, 90W adapter) x 1
HDMI port x 1, DVI port x 1, USB port x 4
e-SATA x 1, RJ45 LAN port x 1
Mic_in x 1, Speaker out x 1, Line_in x 1
Rear Surround x 1, Side Surround x 1
Center/Subwoofer x 1
On-Board
4-pin 12V Power Output Connector for HDD/ODD x 1
Connector
Serial ATA II (RAID 0, 1, AHCI) x 3
Front Panel Connector x 1
Front Audio Connector x 1
IEEE 1394 Connector x 1
CPU FAN Connector x 1, System FAN Connector x 1
USB 2.0 Connector x 2 (Support USB Port x4)
COM1 Connector x 1
TV-Out Connector x 1 (Option)
LVDS_INV Connector (Option) x 1
24 bits LVDS Connector (Option) x 1
BIOS
Award PnP 8Mb SPI Serial Flash ROM BIOS
Board Size
170 mm x 170 mm
Note:
1.
Specifications are subject to change without notice.
2.
Max Memory: 4GB, but can’t be detected 4GB due Intel chipset
limition.

1.3 System Block Diagram
LVDS 24 bit
Connector
DVI
Connector
DDRII SO-DIMM x 2
Intel
Gigabit
LAN
LAN Connect
Componant
Serial Port x 2
Socket P
Intel Merom
Penryn
Chromtel
CPU
7318
(Option)
667/800
MHz
System
Chromtel
Bus
7318
Intel
GM45
Chipset
Dual Channel
DDRII 667/800
Up to 4GB
Winbond
Super
I/O
PCI Bus Mini Card x 2
300MB/s
Serial ATA Port x 3
Intel
ICH9M
Chipset
8M bits Flash
EEPROM
USB Port x 8

Chapter 2 Hardware Installation
2.1 Installation Overview
Generally, when installing a new motherboard and peripherals into a
chassis, people typically follow a certain order of steps for the installation.
The list below are the general steps:
Start
1. Installing CPU
2. Installing CPU Fan and System Fan
3. Installing Memory Module
4. Installing HD, CD-ROM
and SATA Disk , etc
5. Connecting front Panel Cable
6. Installing Other Devices
(USB, Front Audio, etc)
7. Connecting DC Adaptor
8. Connecting Back Panel Ports
(Keyboard, Mouse, etc)
9. Turn on the power Button
10. Loading Default BIOS
11. Installing proVEOS
12. Configuring IP Address
END

2.2 Installing the CPU
This socket supports uFCPGA package CPU, which is the latest CPU package
developed by Intel. Other forms of CPU package are impossible to be fitted in.
1. Unscrew socket screw counter- clockwise.
2. Locate Pin 1 in the socket and look for a golden arrow on the CPU
upper interface. Match Pin 1 and golden arrow. Then insert the CPU into
the socket.
3. Lock the socket screw clockwise to fasten CPU.
Socket Screw
Unlock
Warning:
If you do not match the CPU socket
Pin 1 and CPU golden arrow well,
you may damage the CPU.
Golden arrow
Socket Pin 1
Lock

Support CPU Table
Processor Number
Architecture
Clock Speed
Front Side Bus
L2 Cache
Intel Core 2 Duo (Penryn) CPU
Core 2 Duo T9600
45nm
2.80 GHz
1066 MHz
6 MB
Core 2 Duo T9400
45nm
2.53 GHz
1066 MHz
6 MB
Core 2 Duo P9500
65nm
2.53 GHz
1066 MHz
6 MB
Core 2 Duo P8600
65nm
2.4 GHz
1066 MHz
4 MB
* GM45 Support front side BUS 667 / 800 / 1066 MHz.
Note:
With CPU speed changing rapidly, there may be faster CPU on the market by the time
you received this installation guide. This table is kindly for your reference only.

2.3 Installing CPU Cooler
1. Remove the four screws of the CPU heatsink and take the bracket from
heatsink.
2. Tear off the label from bracket for easily pasted on the bottom of main board.
3. Place bracket properly on the back side as picture.
4. Smear over the thermal compound under the center of heatsink smoothly
and let it be well mixed.
5. Please follow concave of direction on bottom of heatsink, Put the CPU Fan &
heatsink on the processor and lock the four screws of the heatsink with
bracket (on the MB back side). Please make sure the screws are well tied
between the motherboard and heatsink.



Warning:
Always use the correct amount of thermal grease when mounting
the CPU cooler. Follow the instructions closely.


3
1
2
4
Note:
This cooler and picture shown might be different from your purchased product.

2.4 Installing CPU and System Fans
Plug the CPU fan cable to the CPU FAN connector.
If you have a chassis fan, you can also plug it into the SYSFAN connector.
GND
GND
+12V
+12V
Sensor
Sensor
SYSFAN Connector
CPUFAN Connector
Note:
Some fans do not have a sensor pin, so fan monitoring is not supported.

2.5 Installing Memory Module
The motherboard provide SODIMM type memory support. There’re two
SODIMM memory slots which motherboard provided. The installation
of memory module as below.
1. Put the memory module with correct direction. Notice there’s one stick to
make sure direction is correct.
2. Plug in memory module into SODIMM slot with angle 20~30º. Make sure
memory moule plug into slot completely.
3. There’re tabs which located in the side of SODIMM holder. Use finger to
push memory module vertically until the tabs lock memory module tightly.
4. Now, the memory modules have been plugged properly with horizontal flat.

Stick
30º


Tab
Note:
Pay careful attention to align the slot in the middle of the memory module.The tabs of
the DIMM slot will clip to hold the DIMM in place when the DIMM touches the slot’s
bottom. You can hear it click into place.