Wrightline PFPDARM1 User manual
page 1 of 17
PFPDARM1
Product Illustration
page 2 of 17
PFPDARM1Components &
Fasteners
TOOLS REQUIRED
Phillips Screwdriver
1/2" Wrench
1/2" Socket Wrench
ؽ"
ؽ"
4x
1x
1x
4x
8x
4x
3/32"
(2.38mm) 3/16"
(4.76mm) 1/8"
(3.17mm)
1 each
page 3 of 17
Use the Phillips Screwdriver to loosen (but not remove) slatwall bracket
screws.The upper and lower slatwall brackets will move apart.
STEP 1
Install to Slatwall.
page 4 of 17
With screws still installed, hook the slat wall bracket onto the slatwall.
Use the Phillips Screwdriver to tighten screws,drawing upper and lower slatwall brackets toward
one another.
page 5 of 17
STEP 2
Installation Instructions for Monitors with the following hole mounting patterns:
75mm VESA® FPMPMI™ Standard Hole Mount*
100mm VESA® FPMPMI™ Standard Hole Mount*
Custom - does not comply with VESA® FPMPMI™ hole pattern standards*
* VESA® (Video Electronics Standard Association)
FPMPMI™(Flat Panel Monitor Physical Mounting
Interface)
page 6 of 17
STEP 2 continued
Remove monitor pivot from slide bracket.
page 7 of 17
M4 x 10mm
STEP 2a
For monitors with a 75mm VESA®FPMPMI™hole pattern:
Attach monitor directl to pivot.
4x
page 8 of 17
Attach monitor to adapter plate/pivot assembly.
#8-32 x 3/16"
3/32"
(2.38mm)
Attach 75 to 100mm adapter plate to pivot.
M4 x 10mm
STEP 2b
For monitors with a 100mm VESA®FPMPMI™hole pattern:
4x
4x
page 9 of 17
STEP 2c
For monitors that are not compliant with VESA®FPMPMI™hole pattern standards:contact
your APW Wright-line customer service representative.
page 10 of 17
STEP 3
Re-attach
p
ivot (with monitor installed) to slide bracket
.
NOTE: Make sure that the curve on the back
of the pivot wraps around the slide bracket.
Do not overtighten
the pivot knob.
page 11 of 17
Optional
Slide Bracket Mounting Locations
To change location of slide bracket, use a 1/8"
hex wrench to remove screws. Move slide
bracket to desired position, and secure with
screws.
The height of the monitor in relation to the slat wall can be changed according to need. This
illustration shows the lowest and highest slide bracket positions and points out mounting holes.
Note that the highest levels are achieved b mounting the slide bracket up-side-down (relative
to orientation of product as it is shipped).
Slide bracket allows 6" of vertical adjustment
of monitor while mounted to slat wall.
To adjust monitor height: While supporting
monitor with one hand, loosen monitor pivot
knob with the other hand, move monitor up or
down to desired location. Tighten monitor
pivot knob.
6"
(152.4mm)
page 12 of 17
STEP 4
Replace cable covers over "captured" cables.
Remove cable covers.
Route cables as shown.
NOTE: Leave enough slack in
cables to allow free movement.
NOTE: Use clips and ties to manage
cables as needed according to your
equipment configuration.
page 13 of 17
Adjustment 1
Monitor
Side-to-Side
Adjustment 2
Arm
Side-to-Side
Adjustment 3
Monitor
Up and Down
Adjustment 4
Monitor
Portrait/Landscape
PFPDARM1
A
djustment Overview
A
PW-wright line products are factor -
set to provide positive pivot control
and a smooth moving force throughout
the entire range of motion.
To customize our installation, ou will
evaluate the operation of four
separate functions: the side-to-side
movement of the monitor, the side-to-
side movement of the arms, the up
and down movement of the monitor
and the movement of the monitor from
a portrait (vertical screen) to a
landscape (horizontal screen)
orientation.
Specific adjustment procedures for
each function follow.
page 14 of 17
Adjustment 1
Monitor
Side-to-Side
Remove pivot cover. Replace pivot cover.Use 1/2" socket wrench to hold
nut at bottom and 3/16" hex
wrench at top to tighten or
loosen, as needed.
3/16"
1/2"
page 15 of 17
Remove pivot covers.
Adjustment 2
Arm
Side-to-Side
Use 1/2" socket wrench to hold nut at bottom and 3/16" hex wrench at
top to tighten or loosen, as needed. (Replace pivot covers.)
3/16"
3/16"
1/2"
1/2"
page 16 of 17
Adjustment 3
Monitor
Up and Down
Remove pivot povers. Use two 1/2" wrenches to tighten or
loosen, as needed.(Replace pivot covers.)
1/2"
1/2"
page 17 of 17
Adjustment 4
Monitor
Portrait/Landscape
Remove monitor from pivot (or from the 75 to 100mm
adaptor plate, if used).
Reattach monitor to pivot (or to the 75 to 100mm
adaptor plate, if used.)
Use 1/2" wrench to tighten or loosen, as
needed.
1/2"
NOTE: Since the portrait/landscape
feature is factor -set, adjustment is
usuall unnecessar - proceed with these
instructions onl if the monitor rotates too
easil or with great difficult .
Table of contents
