WURM DIN-XP User manual

DIN-XP
Input module
with 16 operation or fault inputs
DIN-XP_V2.7.0_PI_2019-04_EN Subject to technical changes Page 1 of 4
Front view
Features
Inputs for 230V~
Individual selection of operating input or fault input
Load current / zero signal current principle for each input
Setting of priority for all fault inputs
Alarm delay time for all fault inputs
Clear display of signal statuses and voltage statuses
Lamp test and fault message acknowledgement
Simple parameter settings
Alarm relays for priority 1 and 2 available
Selectable relay operating mode
Plug-in screw terminals
Large data memory for signal history
Clear text designations in FRIGODATA XP per input
Evaluation of Prio 1 and Prio 2 subsection faults from a gateway
Direct connection of a CAN-USB to the service socket
Connection to the Wurm system through a Wurm CAN communication bus (C-BUS) and
FRIGODATA XP

DIN-XP
Input module
with 16 operation or fault inputs
Page 2 of 4 Subject to technical changes DIN-XP_V2.7.0_PI_2019-04_EN
Writing conventions
Symbol
Meaning
CAUTION
Avoid the described hazard: Otherwise minor or medium bodily injury or
property damage will result.
WARNING
Avoid the described hazard: Otherwise there is danger from electric voltage that
can lead to death or serious bodily injury.
For your safety
For safe operation and to avoid personal injury and equipment damage through operator error, always
read these instructions, become familiar with the device, and follow all safety instructions on the
product and in this document, as well as the safety guidelines of Wurm GmbH & Co. KG Elektronische
Systeme. Keep these instructions ready to hand for quick reference and pass them on with the device
if the product is sold.
Wurm GmbH & Co. KG Elektronische Systeme accepts no liability in case of improper use or use for
other than the intended purpose.
Target group
These instructions are intended for "service technicians".
Intended use
DIN-XP is an input module with 16 operating or fault inputs.
WARNING
Danger to life from electric shock and/or fire!
Switch off the power to the entire plant when carrying out installation, wiring or removal
work. Otherwise a mains voltage and/or external voltage may still be present even if the
control voltage is switched off. Always remove both power plugs (L and N).
Only qualified electricians are permitted to wire the device.
Use only the correct tools for all work.
Check all wiring after connection.
Take note of the maximum loads on all connections.
Never expose the device to moisture, for example due to condensation or cleaning
agents.
Take the device out of operation if it is faulty or damaged and is therefore compromising
safe operation.
Do not open the device.
Do not attempt to repair the device yourself. If the device requires repairs, send it in with
an exact description of the fault.
CAUTION
Electromagnetic interference can cause faults!

Always use shielded data cables and place them far away from power lines.
Wurm Infocenter
paperless info
Software revisions and validity of documentation
Software version
V2.7.0
2019-04
Documentation status
Any software versions not listed are special solutions for individual projects and are not described in detail in this document.
This document automatically ceases to be valid if a new technical description is issued.
Manufacturer: Wurm GmbH & Co. KG Elektronische Systeme, Morsbachtalstraße 30, D-42857 Remscheid
You can find more information on our website at www.wurm.de

DIN-XP
Input module
with 16 operation or fault inputs
DIN-XP_V2.7.0_PI_2019-04_EN Subject to technical changes Page 3 of 4
Circuit diagram
C-BUS interface
Alarm relay Digital inputs
Installing and connecting
WARNING
Danger to life from electric shock and/or fire!
Switch off the power to the entire plant when carrying out installation, wiring or removal
work. Otherwise a mains voltage and/or external voltage may still be present even if the
control voltage is switched off. Always remove both power plugs (L and N).
This device is designed for top-hat rail
installation. The housing has standard
dimensions and is also suitable for installation in
fuse boxes and distribution cabinets.
The devices can be positioned next to one
another without gaps.
53
106
90
58

DIN-XP
Input module
with 16 operation or fault inputs
Page 4 of 4 Subject to technical changes DIN-XP_V2.7.0_PI_2019-04_EN
Place the device with the upper guide edge on
the top-hat rail.
Then press the device gently downward until it
engages with the fastening safety catch on the
top-hat rail.
For wiring of the data lines, we recommend the use of standard telephone lines 2x2x0.8ø. up to
lengths of 100m. The shielding must be grounded in the control cabinet. For cable lengths from 100m
to 400m, shielded lines with braided sheathing should be used.
We recommend the use of shielded cables for sensor extension.
Cable length
Cross section
Up to 100m
0.75mm²
Up to 400m
1.5mm²
Technical data
Power supply
230V~, +10% / -15%, approx. 4VA
Digital inputs
16 x for 230V~ (common neutral conductor)
Output relay
2 x changeover contacts, 230V~, 4(2)A
Central unit
Single-chip microcomputer, data memory
Monitoring system
Self-monitoring of data memory and microcomputer
Communication
3-wire CAN bus interface with integrated power supply,
galvanically isolated, service socket
Gateway types
The device is supported by the gateways:
Multigate, from V1.0
CMD300, from V1.0
GTW-LAN 2.1
Global fault evaluation is supported by the gateways:
Multigate, from V2.4
CMD300, from V1.0
GTW-LAN 2.1
Dimensions
(WxHxD) 106 x 90 x 58mm (DIN 43880)
Fastening
Top-hat rail TH 35-15 or TH 35-7.5 (DIN EN 60715)
Ambient temperature
Operation: 0...+55°C, storage: -25...+70°C
Weight
About 450g
CE conformity
−2014/30/EU (EMC Directive)
−2014/35/EU (Low Voltage Directive)
EAC conformity
−TR CU 004/2011
−TR CU 020/2011
RoHS II
Valid from
Version 2.7.0