XBOX 360 Installation instructions

Please note that these instructions describe how to disassemble your
Xbox. For most upgrades, modifications, and repairs you will not need to
completely disassemble your Xbox, therefore, parts 6 and 7 are optional.
It is also recommended that you read the instructions completely before
starting, so that you can understand better the purpose of each step.
Tools needed for Xbox 360 disassembly:
T6: To remove hard drive screws
T8: To remove internal Xbox 360 screws
T10: To remove Xbox 360 internal chassis from case
Metal Bar: To remove grey grills on ends of case
Micro Flat Screwdriver: To undo the clips which will separate
the case halves
Basic Disassembly:
Part 1: Preparation
Part 2: Removing the faceplate
Part 3: Removing the grey end grills
Part 4: Separating the case halves
Part 5: Removing the top half of the case
Advanced Disassembly:
Part 6: Removing the power switch
Part 7: Disassembling the hard drive
PPaarrtt11::PPrreeppaarriinnggyyoouurrXXbbooxx336600
1) Remove any game discs from your Xbox 360.
2) Unplug the console from the wall.
3) Remove the hard drive and put it in a safe place. See Part 7 for
disassembly instructions for the hard drive.
4) Place your Xbox 360 in the horizontal position.
5) Make sure you have a good work area, with a place to put the
screws so that you do not lose them, and a place to put the various
case parts where they will not get scratched. You may want to
put a soft cloth underneath the case.
PPaarrtt22::RReemmoovviinnggtthheeffaacceeppllaattee
6) With your right hand, put your thumb in the USB door, and push
to the right (outside edge) of the case. Using your left hand,
squeeze the top and bottom of the faceplate. The faceplate will
pop off. See the arrows in the picture for exact locations.
PPaarrtt33::RReemmoovviinnggtthheeggrreeyyeennddggrriillllss
7) The grey grills are held on by 6 grey tabs. These must be
removed before you can separate the case halves. A view from
the inside of the case is shown in the picture. You must push the
clips shown from the outside so that they will slide over the
pegs that hold them in place.
8) Start with the grill that would be on the bottom of the case (when
the case is horizontal), the one that has the rubber feet on it.
9) Using the metal rod supplied, poke through the vent holes as
shown in the picture and push the grey tabs inward while
pulling upward on the grill. It may be useful to use one of the
other L keys to "hook" the grey grill and pull up.
10) Remove all 6 grey tabs. Pull the grill out and place it to the side.
11) Next remove the tabs from the top grill. With this grill, you
may need to remove the foot on the top rear of the case (when
Xbox is standing upright), there will be a hole underneath that
you can stick the rod through. If you do not want to remove the
foot (because of fear of losing it, because it will not stick as
well once removed and reapplied), you can leave the grill
attached by that one tab and move on to Part 4. You can
remove the final tab with your fingers after you separate the
case halves, but you will have to be careful not to bend it or
break it as it will be in the way.
XXbbooxx336600ddiissaasssseemmbbllyyiinnssttrruuccttiioonnss
Page 1 of 2 www.talismoon.com

PPaarrtt44::SSeeppaarraattiinnggtthheehhaallvveessoofftthheeccaassee
12) Turn the Xbox case around so you are looking at the rear panel
(where the serial number is).
13) You will see 7 small rectangular holes along the seam. There
will have 5 on the right, over the A/V and I/O connectors, and
two over the power plug connector.
14) Take the flat blade screwdriver, and stick it in each hole until
you hear a "snap" sound. Each time you do this, you unclip one
of the seven clips that hold the Xbox 360 case together.
15) After you separate the halves by a few millimeters, you might
want to leave the screwdriver between the halves so that they
do not snap back together while you complete step 16.
16) In the front, there are 4 tabs that hold the Xbox 360 halves
together. You will have to pry each of these up.
17) Pull the top off. When you are successful, you will have the
bottom of the case on the table and the top of the case with the
Xbox 360 metal chassis still attached. At this point, it is very
easy to remove the last of the grey tabs from the inside of the
case if you skipped this step before. Place the grey grills and
the case bottom off to the side.
PPaarrtt55::RReemmoovviinnggtthheettoopphhaallffoofftthheeccaassee
18) There are 6 screws holding the Xbox 360 to the top half of the
case. There is one screw in approximately each corner and two
in the middle (see diagram). There are two more in the center
of the case. Using the T10 key, remove all 6 of these screws.
Place the case top to the side.
PPaarrtt66::RReemmoovviinnggtthheeXXbbooxx336600RRFFMMoodduullee((PPoowweerrSSwwiittcchhBBooaarrdd))
19) To remove the power board, first unclip the white plastic frame
from it. There are two clips, one at the top and one at the bottom.
20) Remove the three screws using the T8 key.
PPaarrtt77::DDiissaasssseemmbblliinnggtthheehhaarrddddrriivvee
21) Using the T6 L Key, remove the 4 screws from the back of the
hard drive. The 4th screw is under the silver Microsoft sticker.
22) Taking care not to lose the little spring that works the release
button, remove the plastic housing.
23) You can now slide the hard drive out of the housing.
DISCLAIMER: Talismoon offers products for Xbox and PS2 enthusiasts. Use of our products happens at your own risk. Talsmoon is not responsible
for your console or your ability to work on your console. Talismoon is also not liable for any physical or consequential damages. Consequential damages
are defined as any damage which is a consequence of using this product or our website (data loss; hardware loss; or economic losses like profit loss,
customer loss, or time loss). Talismoon's liability is limited to the cost of the product purchased from us.
Page 2 of 2 www.talismoon.com