Xentino VX110 User manual
“focus differently”
www.xentino.com
USER MANUAL
Version 2.0.0
Models : VX110
“focus differently”
www.xentino.com
Copyright Notice
Copyright ©2018 Xentino Technologies Corp. All rights reserved. No part of this document may be
copied, reproduced, or transmitted by any means, for any purpose without prior written permission.
Disclaimer
We shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or
consequential damages resulting from furnishing this material, or the performance or use of this
product. We reserve the right to change the product specification without notice. Information in this
document may change without notice.
Trademarks
Microsoft Win98, Windows 2000, WinXP, Win Vista and Win7 are registered trademarks of Microsoft
Corporation.
Xentino are registered trademarks of Xentino Technologies Corporation.
General: All other brand and product names mentioned herein may be registered trademarks of their
respective owners. Customers should ensure that their use of this product does not infringe upon any
patent rights. Trademarks mentioned in this publication are used for identification purposes only and are
properties of their respective companies.
“focus differently”
www.xentino.com
Chapter 1
Introduction
VX110 VDSL2 Ethernet
Extender
is a high-speed Ethernet Extender with one Ethernet port (RJ-45 connector) and
one VDSL port (RJ-45 connector). It is a bridge mode modem, well accommodating VDSL2 (Very-high-data-rate
Digital Subscriber Loop) technology to extend Ethernet service over single-pair phone line. It is compliant to ITU-T
G.993.2 standard and supports VDSL2 30a profile that features 100Mbps of symmetric data rate over the existing
copper wires. Supporting both symmetric and asymmetric transmission, it can reach up to 100/100 Mbps bandwidth
(line rate) within 300M or 10/10 Mbps (line rate) for 1 Km long range connections. By providing ultra-high speed, the
VDSL2 VX110 Ethernet Extender makes your telephone line achieve its best performance than before. It has the
advantage of minimum installation time (simply as plug-n-play) and minimum expense by allowing video streaming and
data to share the same telephone pair without interference.
VX110 VDSL2 Ethernet Extender delivers everything needed to quickly deploy a high-speed IP-based network for
providing high-speed Internet access, video-on demand services and voice services. The resulting compact, cost-
effective form factor offers Systems Integrators, small business owners an attractive Long Reach Ethernet solution.
1.1 Features
Cost effective bridge function to connect two Ethernet LAN
Support flow control on Fast Ethernet port via PAUSE frame or Back Pressure
IEEE 802.1Q VLAN tag transparent
Easy installation via simple plug-and-play
Selectable CPE and CO mode via DIP switch:
Two working modes are built in the same unit, which keep the flexibility of installation and easy provision of
service but lower inventory of service provider
Selectable VDSL2 profile mode (17a or 30a):
Support up to VDSL2 30a profile to ensure high data rate.
Selectable target band plan:
Symmetric: Support the band plan G.997 and provide the symmetric transmission on both downstream and
upstream.
Asymmetric: Provides highest line rate in short range in asymmetric mode.
Selectable target SNR margin
Compatible with the D24M/D08M DSLAM & third party DSLAM.
Compatible with the 2U 19-inch, 17-slot chassis.
“focus differently”
www.xentino.com
1.2 Specification
4-position DIP Switch
Selectable CO or CPE mode
Selectable 30a or 17a (VDSL2 Profile)
Selectable Band plan (Symmetric or Asymmetric)
Selectable target SNR margin (6dB or 9dB)
LED:
LAN: ACT/LNK,10/100Mpbs, Half/Full Duplex
VDSL: Power On/Off, CO/CPE, Idle/Trained/Link
Performance* (AWG24 Wire)
Downstream/ Upstream
17a Profile
600M
42/46 Mbps
1000M
18/13 Mbps
1500M
12/3 Mbps
2000M
5/2 Mbps
30a Profile
600M
40/45 Mbps
900M
22/19 Mbps
1200M
16/7 Mbps
1800M
8/2 Mbps
2100M
5/2 Mbps
*The above performance data is for reference only, the actual data rate may vary depending on the quality of the copper wire and environmental
factors.
LAN Interface:
RJ-45 connector
Complying with IEEE
802.3/802.3u/802.3x
10/100 Base-T Auto-Negotiation, Auto-
MDI/MDI-X.
VDSL Interface:
RJ-45 connector
DMT Encoding
Complying with ITU-T
G993.1/993.2/G.997.1
On-board surge protection
Regulatory Compliance
CE
FCC Part 15 Class B
EN60950
Power supply:
Option 1: 5 -20 Vdc over terminal block
(External Power Adaptor not included)
Option 2: 12 Vdc over 2.1mm DC Jack
(External Power Adaptor included)
Dimension: 73.4mm x 96.2mm x 22.8mm
Temperature: -20°C ~ 65°C
Humidity: 0%~95%RH (non-condensing)
“focus differently”
www.xentino.com
1.3 Applications
LAN Extender Application
“focus differently”
www.xentino.com
Chapter 2 Hardware Installation
This chapter shows the front panel and how to install the hardware.
2.1 Front Panel
Front panel can be separated into five parts from left to right:
(1) DIP switch
(2) RJ-45 connector for Ethernet
(3) LEDs for Ethernet
(4) LEDs for VDSL
(5) RJ-45 connector for VDSL
“focus differently”
www.xentino.com
1. The RJ-45 is designed to connect to the Local Network with the Unshielded Twisted Pair (UTP) cable. The
LEDs on top of RJ-45 connector show the status below:
2.
LEDs for LAN
blinking
On
Off
Activity
Link UP
Link UP
100Mbps
10Mbps
Full Duplex
Half Duplex
LED
Color
Status
Descriptions
PWR(Power LED)
Green
On
Lights to indicate that the VDSL2 bridge had power
Green
Off
The device is not ready or has malfunctioned.
LNK(Ethernet LED)
Green
On
The device has good Ethernet connection.
Green
Blinking
The device is sending or receiving data.
Green
Off
The LAN not connected.
LNK RT(VDSL Link)
Green
On
RT mode.
Green
Blinking
Handshaking/Transmit & Received data
Green
Off
The device not ready.
FUL 100(LAN Link)
Green
On
The device is link on 100M Full duplex and ready.
Green
Blinking
The device is sending or receiving data.
Green
Off
The device is link on 10M Full duplex and ready.
“focus differently”
www.xentino.com
3. The following table describes the DIP Switches’ setting.
Pin 1
Pin 2
Pin 3
Pin 4
Side
Channel
Rate Limit
SNR
Off
OT
30a
Symmetric
9dB
On
RT
17a
Asymmetric
6dB
Pin 1: OT, RT switch
OT: LAN Extender acts as Central Office (CO) side.
RT: LAN Extender acts as Customer Premise Equipment (CPE) side.
Pin 2: Impulse noise protection
30a: High Speed Mode. Provides communication protection for up to 250ms impulse noise with
latency less than 6 ms.
17a: Long Reach Mode. Direct data transmission with latency less than 1 ms.
Pin 3: Band Plan
Symmetric: Support the band plan G.997 and provide the symmetric transmission on both
downstream and upstream.
Asymmetric: Provides highest line rate in short range in asymmetric mode.
Pin 4: General protection
9dB: Better channel noise protection with SNR up to 9 dB
6dB: Original channel noise protection with 6 dB SNR.
“focus differently”
www.xentino.com
4. The following table describes the LEDs’ function of the product.
LEDs for VDSL
blinking
On
Off
Device Power ON
Device Power OFF
CPE-mode
CO-mode
Slow: Idle
Fast: Training
Linked
Off line
2.2 Rear Panel
The DC Jack on the rear panel can be connected to power supply adaptor with the DC input.
“focus differently”
www.xentino.com
2.3 Installation
Please see the illustration below
“focus differently”
www.xentino.com
Appendix I
Connector
Architecture
Ethernet Port Connector
(RJ-45)
The Ethernet Port interface is an 8 position Modular Jack. The table below displays the pin out assignments.
Pin Number
Assignment (MDI-X)
Figure
1
RX+; Receive data +
1
8
1
8
F
r
o
n
t
V
i
e
w
Top
V
i
e
w
2
RX-; Receive data -
3
TX+; Transmit data +
4
Not used
5
Not used
6
TX-; Transmit Data -
7
Not used
8
Not used
“focus differently”
www.xentino.com
VDSL Interface Pin Assignments (RJ-45)
The VDSL interface is standard eight-pin modular jack. The table below displays the pin out
assignments.
Pin Number
Desc
r
i
p
t
io
n
F
ig
u
r
e
1
Not used
1
8
1
8
F
r
o
n
t
V
i
e
w
Top
V
i
e
w
2
Not used
3
Not used
4
ANALOG Input/Output
5
ANALOG Input/Output
6
Not used
7
Not used
8
Not used
“focus differently”
www.xentino.com
Appendix II
Chassis
Accessory
There is also the Chassis solution for application on the rack in CO side. The major feature of the
Chassis is listed below:
•
2U, 19”, 17-Slot rack
•
Support 17-slot in one unit
•
Power Input: AC: 100 ~240V or DC48: 36 ~ 60V
•
Cross flow cooling fan built-in
•
VX110 units are hot swappable
Specifications
Power Input: AC : 100 ~240V or DC48 : 36 ~ 60V
Power Consumption: >60W
Dimensions: 76 X 212 X 88 mm (D x W x H )
Weight: 7.9Kg
Temperature: 0 ~ 50°C (Operating), -10 ~ 70°C (Storage)
Humidity: 10 ~ 90% non-condensing
Certification; CE, FCC, RoHS Compliant
MTBF: 65,000 hrs
“focus differently”
www.xentino.com
LIMITED WARRANTY
What the warranty covers:
We warrant its products to be free from defects in material and workmanship during the warranty period. If a product proves to be defective in
material or workmanship during the warranty period, we will at its sole option repair or replace the product with a like product with a like
product. Replacement product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
The device is warranted for 1(one)year for all parts and one year for all labor from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product, on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to follow instructions supplied
with the product.
b. Repair or attempted repair by anyone not authorized by us.
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electric power fluctuations or failure. f. Use of supplies or parts not meeting our specifications.
g. Normal wears and tears.
h. Any other cause that does not relate to a product defect.
3. Removal, installation, and set‐up service charges.
How to get service:
1. For information about receiving service under warranty, contact our Customer Support.
2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address (d) a
description of the problem and (e) the serial number of the product.
3. Take or ship the product prepaid in the original container to your dealer, and our service center.
4. For additional information, contact your dealer or our Customer Service Center.
Limitation of implied warranties:
THERE ARE NOWARRANTIED, EXPRESSED OR IMPLIED, WHICH EXTEND BEYOND THE DESCRIPTION CONTAINED HEREIN INCLUDING THE
IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of damages:
Our LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE PRODUCT. We SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES BASED UPON INCONVENCE, LOSS OF USE OF THE
PRODUCT, LOSS OF TIME, LOSS OF PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS
RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE POSSIBLITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSOMER BY ANY OTHER PARTY.
“focus differently”
www.xentino.com
Table of contents
