Xit404 Manta series User manual

TOKINA 10-17 LENS

GRAY ZOOM RING

SHOWING THE

UNLOCKED

POSITION

ROTATE GEAR INTO

LOCKED POSITION

RED

MANTA

GEAR

ORIENT GEAR IN

THE UNLOCKED

POSITION

SLIDE GEAR ONTO

LENS AND PRESS

INTO ZOOM RING

ZOOM RING PROPERLY

LOCATED ON LENS

SLIDE ZOOM RING

ONTO LENS FROM BACK

UNTIL IT STOPS

Thank you for purchasing Xit 404’s Tokina 10-17mm Zoom Ring to use

with our Manta Gears. On the back is our warranty information to help you

prolong the life of this product.

This product is in our Manta Line. The advantage of the Manta Line of

Rings and Gears is that the parts are interchangeable. For example the

Manta Gear fits on all Manta Focus/Zoom Rings as well as our

Manta Teleconverter Extension Rings. This allows you to purchase one

gear that mates with a variety of lenses.

Assembling the Zoom Ring to your Manta Gear

Make sure your lens switch is in auto focus mode. Look at the drawing to

the left and note which end of the lens the Zoom Ring slides onto. Then

follow the instructions below.

1. Slide the Zoom Ring onto your lens from the front of lens until it stops.

2. Slide the Manta Gear on from the back of the lens. Align the white

dot on the Manta Gear with the unpainted red dot on the Focus Ring.

Then press the two parts together. Once the the two parts are fully

mated, while holding the Focus Ring with one hand, and pressing

the red Manta Gear latch with thumb, twist the Gear until the white

dots line up (note: the locked icon). The Manta Gear is now locked

onto the Focus Ring.

Disassembling the Focus Ring

1. Remove the Manta Gear by pressing and holding the latch on the

Manta Gear. Then twist it until the white dot on the Manta Gear is

lined up with unpainted red dot on the Focus Ring (note: the

unlocked icon).

2. Pull the Manta Gear off the lens.

3. Remove the Focus Ring by reversing the steps 1 and 2. above The

white dot and the unpainted red dot will not be lined up after step 2,

allowing you to slide the Focus Ring off your lens.

RED GEAR LATCH

TOKINA 10-17 LENS

GRAY ZOOM RING

SLIDE ZOOM RING

ONTO LENS FROM BACK

UNTIL IT STOPS

RED

ORIENT GEAR IN

THE UNLOCKED

POSITION

SLIDE GEAR ONTO

LENS AND PRESS

INTO ZOOM RING

RED GEAR LATCH

SHOWING THE

LOCKED POSITION

PRODUCT CODE: GM3201TK

Revsion 2.0 - APR2013 www.xit404.com

TOKINA FISHEYE10-17mm 3.5-4.5:2.8 (CANON)

MANTA ZOOM RING ASSEMBLY INSTRUCTIONS

FDM parts - a brief description

Xit 404 manufactures a number of its parts using a process called Fused Deposition Modeling (FDM). This process involves extruding a thread of plastic and laying it down

in thin layers to build a part. This enables us to supply you products that enhance your underwater photography and videography.

Care and Maintenance

The FDM part is impact resistant and will withstand most drops from table height. However, as with all plastic parts, they cannot withstand excessive pressure and

force without breaking. Being careful means handling the product during assembly with a light touch, do not force.

If your part gets wet let it drip-dry for about an hour. If you have to pack it before it is dry then wrap it in something absorbent such as a paper towel, tee shirt or sock

and put it into a plastic bag. This will keep your other parts from getting dripped on.

FDM Plastic Part Warranty

FDM parts are guaranteed to be free of manufacturing defects for a period of one year from date of purchase. Unnecessary force can cause excessive wear and

possibly break the parts voiding warranty. Damaged or broken parts will be inspected. If Xit 404 determines that the parts were misused or abused, warranty will be void.

Valid purchase receipt isrequired for all warranty claims.

TOKINA 10-17

LENS WITH ZOOM

RING, 1.4X EXTENSION

RING AND GEAR

TOKINA 10-17

LENS WITH ZOOM

RING, 2X EXTENSION

RING AND GEAR

Revsion 2.0 - APR2013 www.xit404.com

TOKINA FISHEYE10-17mm 3.5-4.5:2.8 (CANON) (ZOOM)

WARRANTY INFORMATION