XL displays Centro Multimedia Kit 2 User manual

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
2
Affix upper post to lower post by positioning female end
centrally over male fitting (C), and rotate until assembly
drops into position, continue rotating clockwise through
90º to secure (D).
A
1
B
Place base plate on the floor, position lower post
centrally over male fitting of base plate (A), and
rotate until assembly drops into position, continue
rotating clockwise through 90º to secure (B).
D
C90º
3Repeat for remaining base and posts to complete
assembly of uprights.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
4.1 4.2.1 4.2.2
4.2.3 To join the horizontal (H, H1, and H2) and vertical (V and V1) frame profiles:
4.1) Loosen grub screws and slide connector bars halfway out of the channel.
4.2) Join profiles ensuring graphic fixing strips are aligned and the expanding
clamps are at either end of the assembled profiles.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
5.2i) Centre vertical ‘V1’ differs due to the presence of twin graphic fixing strips.
5.2ii) Bottom horizontal ‘H2’ differs with the introduction of the adjustable thumb screw foot in the centre.
5.3) Tighten grub screws to make secure.
5.2i 5.2ii 5.3

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
6.1 6.2 6.3
Connect two vertical (V) 1531mm assembly rails at 90º to each end
of the 1500mm horizontal rail (H2) ensuring that the graphic fixing
strip is outermost and the verticals are flush with the end of the
1500mm rail. Bottom horizontal 1500mm rail (H2) should have an
adjustable thumbscrew foot in the middle of a 260mm connector bar.
Connect middle vertical rail (V1- with twin graphic fixing strips) to centre
of the assembled horizontal (H2) using the expanding clamp. Tighten 3
bottom grub screws in expanding clamps on verticals to secure to horizontal.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
7.1 7.2 7.3
Connect second horizontal 1500mm rail assembly (H), using the
expanding clamps, to top of assembled verticals (V, V1 and V)
ensuring that the graphic fixing strip is at the bottom. Tighten
grub screws on vertical rails to secure. This completes the bottom
section of the framework.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
8.1 8.2 8.3
For the top section of the framework, connect the two 220mm profiles,
with expanding clamps at both ends and the single fixing strip, at 90º
flush to each end of the third 1500mm horizontal rail (H). Ensure that
the graphic fixing strip on the verticals are outermost and the graphic
fixing strip on the horizontal 1500mm rail is at the top. Affix 220mm
vertical profile, with expanding clamps at both ends and twin fixing
strip, to middle of 1500mm horizontal. Tighten lower grub screws
adjacent to horizontal rail assembly to secure 220mm verticals.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
9.1 9.2 9.3
Slot final top horizontal 1500mm rail assembly (H1) to
the 220mm verticals, ensuring that the graphic fixing
strip is at the top. Tighten grub screws on verticals to
secure framework. This completes the top section
of the framework.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
10.1 10.2
Slot the bottom section framework into the channel of the assembled
post at 90º to the base plate. Ensure framework is equidistant from
the base plate, adjustable foot rests on the ground, and graphic fixing
strip is adjacent to the floor. Tighten both grub screws in the horizontals
(H2 and H) to secure.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
Slot open end of framework into other assembled post, at 90º
to the base plate. Ensure bottom section is equidistant from
the floor at both ends and the adjustable foot rests on the floor.
Tighten remaining grub screws in horizontals (H2 and H) to
secure bottom section framework to both post assemblies.
11.1 11.2

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
Affix the top section framework into the same channel as the
bottom section ensuring graphic fixing strips are all on the same
side of the system. Leave a gap of 60mm in between bottom and
top framework assemblies and tighten all grub screws in horizontals
(H and H1) to secure to post.
12.1 12.2

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
13
Starting from the top left-hand side of the system, unroll the
first graphic panel and align the magnetic tape with steel
fixing strips of the framework. Work across the frame, taking
care not to crease the panel. Repeat for remaining graphic panel.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
Remove two inner screws from LED/LCD mounting bracket and loosen two outer screws so there is
sufficient gap between connector bars to slide onto framework profile.
14.1 14.2 14.3

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
15.1 15.2 15.3
Position and lower outer screws
centrally over upper horizontal
rail in aperture.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
16.1 16.2 16.3
Raise screen mount so bottom holes
are above the lower horizontal rail in
aperture. Re-insert 2 screws through
lower/inner mount holes (4 openings
from either end of the screen mount)
and clearance holes in 2 off 260mm
connector bars adjacent to mount.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
17.1 17.2
Align other 2 off 260mm connector
bars, located behind horizontal rails,
and screw into threaded holes.
Ensure bottom screws rest on lower
horizontal rail, mount is in centre of
aperture, and tighten all 4 screws
to secure assembly.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
19
Position screen centrally
above bracket and lower
until top of both mounting
arms hook over mount.
18
With the elongated holes on the
mounting arms uppermost, align arms
centrally with 4 off fixing points on rear
of screen equidistant from the top.
Insert 4 off screws with suitable washers
and tighten.

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
20.1
Slide locking bar between the
mounting arms and the plasma
mounting bracket if desired. For extra
security, there is a facility to add a
padlock to the locking bar.
20.2

www.xldisplays.co.uk
01733 511 030
Centro Multimedia Kit 2
Assembly Instructions
21
To complete Centro Mutimedia Kit 2 display,
please affix podium table to the front of one
of the posts.