XPower B-3 User manual

Introducon
XPOWER model numbers B-3 / B-4 / B-5 are ETL / C-ETL Cerfied Professional Level 2-in-1 Pet
Dryers + Vacuums with the finest engineering design. XPOWER Pet Dryers + Vacuums help dry
your pets safely and quickly – whether small or large breeds, or pets with short or long hair!
Special Features:
• Extra low noise level.
• 2-in-1 funcon: Pet Dryer and Vacuum.
• Powerful motor from 2 HP to 4 HP.
• Opmal Integraon of motor and housing design.
• High impact and rugged ABS housing material.
• Easy-to-change and washable filter.
• 2-speed sengs for B-3 or variable speed sengs for B-4 & B-5.
• ETL/C-ETL Cerfied.
• 6  (B-3) or 8  (B-4 & B-5) heavy duty flexible hoses.
• Heavy duty blower nozzles for different pet drying applicaons.
• Compact, lightweight and portable, ideal for “house calls” and home use.
- 1 -
XPOWER MANUFACTURE, INC.
220 Clary Avenue
San Gabriel, CA 91776, USA
Tel: [phone], Fax:
626-285-3302
www.xpower.ws
PLEASE READ AND SAVE THESE INSTRUCTIONS
2-IN-1
PET DRYER + VACUUM
OWNER’S MANUAL
MODEL: B-3/B-4/B-5
Nozzles
included

Table of Contents
Introducon ................................................................................................................................
Operaon ...................................................................................................................................
Specificaons .............................................................................................................................
Safety Instrucons .....................................................................................................................
Parts List ....................................................................................................................................
Warranty / Service .................................................................................................................
Warranty Registraon Form ......................................................................................................
1
2
3
4
5
7
8
9
1. Place the dryer on a flat surface. Plug the electrical cord into a 3-prong GFCI outlet.
2. To use as a dryer, connect the hose to the front hose connector and aach the desired nozzle.
Keep the inlet filter and crossed cover in place on the rear cover. Turn on the switch to the
desired speed.
3. To use as a vacuum, detach the hose from the front connector, then remove the inlet filter and
crossed cover of the rear cover. Connect the hose to the rear cover connector and aach the
desired nozzle. Turn on switch to the desired speed to vacuum.
4. All units in use must be supervised at all mes.
Operaon
:
To use as a dryer:
connect the hose to the
front hose connector.
To use as a vacuum:
connect the hose to
the rear cover
connector.
6,
- 2 -

Safety Instrucons
WARNING: IMPORTANT SAFETY PRECAUTIONS!
PLEASE READ COMPLETELY BEFORE USING PRODUCT!
When using electrical appliances, especially when children or animals are present, basic safety
precauons should always be followed to reduce the risk of fire, electric shock, and personal
injury.These include, but are not limited to the following:
Do not leave the dryer and animal
unaended while the product is in use.
Unplug dryer when not in use.
Do not use extension cords with the dryer
product.
Do not unplug unit by pulling on cord.
Do not expose dryer to rain or water.
Unplug unit before aempng any
maintenance or service.
Do not let air-intake get clogged.
Do not direct dryer air towards eyes or ears of
people or pets.
Never use dryer with a damaged cord/plug or
when unit has been dropped, damaged, or
exposed to rain/water. Please call our
Technical Department for service or repair.
Do not use any other nozzles not intended
for usewith the dryer.
Do not operate without filter in place. Keep
filter clean, as a dirty filter limits air intake
and may damage the motor or cause
overheang.
Plug only into a properly grounded
receptacle. Always confirm that the
amperage rang of the electrical outlet
complies with the Dryer + Vacuum rang.
Do not use product for anything other than
its intended purpose.
Do not aempt to perform any service or
maintenance not outlined in the instrucon
manual.
- 3 -
Specificaons
Model
Volt/Cycle
Horse Power
Amp Draw
Unit Weight
Speeds Control
Size (H x W x D)
Cord Length
Overheang
Protecon
B-3
115V / 60Hz
2 HP
8A
8.2 lbs
2 Speeds: Hi / Low
13” x 6” x 9”
10 
Thermal
B-4
115V / 60Hz
3 HP
10A
10.8 lbs
Stepless
14” x 6.5” x 9.5”
10 
Dual Thermal
B-5
115V / 60Hz
4 HP
12A
11.5 lbs
Stepless
14” x 6.5” x 9.5”
10 
Dual Thermal
Housing Material
Safety Cerficaon
ABS
ETL/C-ETL
ABS
ETL/C-ETL
ABS
ETL/C-ETL
Hose Length 6  (1.5 Dia”) 8  (1.5 Dia”) 8  (1.75 Dia”)
Max. Airflow 100 CFM 120 CFM 140 CFM
•
•
•
•
•
•
•
•
•
•
•
•
•
•
- 4 -

- 5 -
- 6 -
Maintenance
Product Maintenance:
1. To keep the Pet Dryer + Vacuum clean, use a damp cloth to wipe the surface of the housing.
2. Never clean the unit with water.
3. When not in use, unplug and store the Pet Dryer + Vacuum in a dry indoor place and keep out of
reach of children.
4. Always disconnect the Pet Dryer + Vacuum from its power source before performing any
maintenance or cleaning.
Cleaning Dryer Dust Case, Rear Cover and Filters:
The Filter System for the XPOWER Pet Dryer + Vacuum (including dust case, rear cover and filters)
should be kept clean regularly. If the dust case is full of hair and / or dirt or the filters become
heavily coated, the air output and input of your Dryer + Vacuum will reduce and this can cause
damage to the motors or cause the motors to overheat. You should never operate the dryer
without filters in place.
IMPORTANT!
Always turn off the unit and disconnect from electrical outlet before cleaning.
17
3
1
45
8
2
910 11
12 13
14 15
16
19 20 21
18
6
Parts List
7
1 LeHousing 8 Motor 15 Crossed cover
2 Right Housing 9 Motor rubber sleeve16 Inletfilter
3 Switch 10 Dustproofcover 17 Hose
4 Air outlet grid 11 Motor filter 18 Round groomer rake
5 Motor rubber sleeve12 Dustcase 19 Cone nozzle
6 PCB board 13 Dustcase filter 20 Flat nozzle
7 Brush14 Rear cover 21 Square nozzle
Wall Mount shown (oponal)

Your Name / Company Name
Contact Name Title
Address City State Zip
Phone Fax E-mail
PetDryer + Vacuum Model # Serial # :
Date of Purchase / / Purchased From
WARRANTY REGISTRATION
Please complete and mail or fax for your product warranty. For mulple units, please list serial numbers on a separate sheet of paper.
Address:
XPOWER MANUFACTURE, INC. 220 Clary Avenue San Gabriel, CA 91776, USA
Tel: [phone], Fax: [phone]
1.Turn the rear cover
counter-clockwise to
remove the cover.
2.Take thecomplete set of dust
case and rear cover out of the
unit. Keep the rear cover on
top so that the hair and dirt are
in the dust case.
3.Dump the hair and dirt out
of the dust case.
4. Rinse all filters(motor filter,dust case filter,inlet filter) with water.
5. Reinstall in reverse order when all parts are completely dried.
- 7 -

TO:
XPOWER MANUFACTURE, INC.
220 Clary Avenue
San Gabriel, CA 91776, USA
Tel: [phone], Fax: [phone]
From:
XPOWER Limited Warranty
XPOWER warrants this product to be free from defects in material and workmanship for a
period of one (1) year from the date of original purchase.
Wearable parts including but without limitaon, filters, motor brushes, hoses and power
cords are excluded from the warranty.
The liability of XPOWER is limited solely to the cost of the repair or replacement of the unit at
XPOWER’s discreon. This warranty does not cover normal wear of parts and does not apply
to any unit that has been tampered with or used for commercial purposes. This limited
warranty does not cover damage caused by misuse, abuse, negligent handling or damage due
to faulty packaging or mishandling in transit. This warranty does not cover damage or defects
caused by or resulng from damages from shipping or repairs, service or alteraons to the
product or any of its parts, which have been performed by a repair person not authorized by
XPOWER.
Service
For Warranty service and parts replacement, you must:
A. Call 1-855-855-8868 for a RMA (Return-Merchandise-Authorizaon) number.
B. Have original proof of purchase.
C. Use the original undamaged packaging or an Industrial cerfied packaging method.
The end user will be responsible to ship back the unit (with RMA Number showing on the
shipping label) to the XPOWER Service Department. XPOWER to inspect, assess and advise
the repairs needed and the applicable cost.
- 8 -