XSAT XT-XJ4 User manual

XT-XJ4
User Manual
Audio Phone
Read this manual carefully before using the product, and keep it well for future use.

1 2
8888

1. Parts and Functions
187
33.2
150
97.1
2 1
8888
Handset
7 segment LED
Menu button
Cancel button
Unlock 2nd button
Speaker
Handset line
Side View
Up button
Down button
Unlock button
7 segment LED Display setting informations
Handset Pick up to communicate with visitor
Hand line Connect handset with monitor
Unlock button Press to release the door
Unlock 2nd button Press to release the second door
Up button Press to move up or increase the value
Down button Press to move down or decrease the value
Menu button Press and hold for 2s to open the setting menu shortcuts.
Press to conrm settings.
Cancel button Press to cancel the operations
Speaker Send out vioce from the visitor
Key functions

2. Operation Instructions
3. Setup Instructions
1) Door opening function:When visitor calls from outdoor station, the monitor rings,
pick up handset to talk with the visitor, then press the Unlock button to open the door.If
the system connect 2 locks,press Unlock 2nd button to open the second door.
2) Entrance monitoring: Pick up handset in standby mode,the LED will be shown a
scroll information "Intr Call",press Up button or Down button to stop the scroll,and
the LED show "ds-x"(x=1~4,refer to part 3-Numbers of door station),it means that the
monitor switch "x" door station to mionitor.Press Up / Down button to increse/decrese
the value,and press Menu button to conrm the setting.
3) Inner call: Use Up / Down button to select "-ALL" item on LED,then press Menu
button to activate the inner call,all monitors connected to the system will ring at the
same time.Pick up any monitor,the others will stop ringing immediately.(note that the
user code must be the same for all monitors to activate the inner call function)
4) Intercom call:Use Up / Down button to select "C-xx" (xx=00~31,refer to part3-
Numbers of indoor monitor)item on LED,then press Up / Down button to increse/
decrese the value,and press Menu button to conrm the intercom calling.(note that the
user code must be different for all monitors to activate the intercom call function)
Press Menu button and hold for 2s in standby mode,the LED will be shown a scroll
information "User Set-",press Up button or Down button to stop the scroll,and the LED
show the setting items.Press Menu button to select setting items.
Setting
Item
L E D
state Description Default
Door station
call tone 1-xx
Set the ring tone calling from outdoor station.Total
12 pieces ring tones can be selected(xx=01~12),press
Up / Down button to increse/decrese the value,and
press Menu button to conrm the setting.
02
Intercom
call tone 2-xx
Set the ring tone calling from intercom call
or inner call.Total 12 pieces ring tones can be
selected(xx=01~12),press Up / Down button to
increse/decrese the value,and press Menu button to
conrm the setting.
12

Setting
Item
L E D
state Description Default
Ring volume 3-rx Set volume for call tone,rang from 0~9. 6
Speaker volume 4-Lx Set volume for speaker,adjust the voice from
outdoor,rang from 0~9. 6
Microphone
volume 5-tx Set volume for microphone,adjust the voice from
user,rang from 0~9. 6
Numbers of door
station 6-0x
Maximum 4 door stations can be selected,this
item is used to set the numbers of door station
that can be surveilled by indoor monitor.refer to
part 2 ->Entrance Monitoring.
1
Numbers of
indoor monitor 7-xx
Maximum 32 indoor monitors can be selected,this
item is used to set the numbers of indoor monitor
that can be selected to intercom.refer to part 2
->Intercom call.
04
Keypad sensitivity 8-sx Rang from 0~2,The larger you set the value,the
stronger it will be,"0"-slow,"1"-normal,"2"-fast. 1
Slave adress
setting for monitor 9-dx Rang from 0~3,"0"-master monitor,"1~3"-slave
monitor. 0
Restore to default
setting 9-FS
The restore to default function allows the user to
recover the settings to factory setting.Select "9-
FS" item on LED,then press Up button,"YES"will
be asked,press Up button again to restore the
settings to default.
-
4. Specication
●Power Supply: DC24V
●Power Consumption: standby 20mA,working 70mA
●7 segment LED: 4 digits dynamic
●Wiring: 2 wires, non-polarity
●Dimension: 187(H)X97(W)X33(D)mm
The design and speci cations can be changed without notice to the user. Right to interpret and copyright of this manual are preserved.