Xstatic X-240BAR RGB User manual

2
High Power Indoor Bar Washer, 240 RGB LED
User Manual

3
CAUTION! READ BEFORE USE!
For your own safety, please read this user manual carefully before you
initially power up your xture.
● Examine packaging to ensure all parts included
● Disconnect all power and other cables prior to servicing
● Always make sure to provide adequate ventilation
● Keep this device away from rain and moisture!
POWER
Be sure you have the proper power
cables for the xture. A 120v cable with a
Standard PC Power connector is required,
and included with the unit. If the xture
expereiences a power failure, check the fuse
located on the power input port.
CONNECTIONS
Remote control and linking is available via
four operation modes: DMX 512 Control, Auto
and Master/Slave, and Sound Active modes to
form different led effects, and DMX-512
connection to connection between xtures.
(Input and Output Ports seen here. See the DMX
page for cabling details and Daisy-chaining
specics on Page 11).
SAFETY INSTRUCTIONS:

4
FEATURES:
● RGB Color Mixing
● Color Strobe Effect
● Color Mix Effect Programs
● LED Chases (Adjustable Speeds)
● Electronic Dimming 0-100%
● Operating Modes: Sound Active, Master /
Slave, or DMX-512 Control Protocol
● DMX Channel modes: 2, 3, 4, 7, 14, or 26
● Digital Display for Address and Function
Settings
● IR Remote Control
Please Note: Specications and improvements in
the design of this unit and this manual are subject
to change without any prior written notice.

5
DMX Control and Chain Connections:
You can connect the DMX-output of a controller directly to the DMX-input of
the xture. If connecting mulitple units, be sure to use the proper cabling.
TERMINATION NOTE: These units are not self terminating. If the last xture
in the DMX chain will need to be terminated with a Terminator. (page 11)
● Voltage: 100V~240V, 50Hz~60Hz
● LEDs: Red x 96, Green x 72, Blue x 72
● Power Consumption: 36W
● Weight: 6 lbs / 2.6Kgs
● Dimensions: 42” x 3” x 3” / 1006mm x 76mm x76mm
● Colors: RGB Color Mixing
● DMX In and Out
● LCD Control Screen
● Beam Angle: 40 degrees
TECHNICAL SPECIFICATIONS:

6
MENU / CONTROLS:
SETUP MENU: You can easily setup and control your 240 RGB LED Bar
from the on-board LCD screen. Using the MENU, SETUP, UP and DOWN
buttons, you will nd the following options to select and modify:
LED DISPLAY OPERATION - These instructions will provide access to the
setup and control of the DMX light.
1. AUTO MODE
Press the MODE button until AUTO displays on the Menu screen. The xture
comes with 24 built-in programs titled Pr.02 - pr.24 where the user can
set the operation speed and strobe speed. The presets will run in loop until
stopped.
CHOOSING COLORS:
To select a Static Color, press the MODE button until you see Pr.0 1. Then
using SETUP and UP or DOWN buttons to choose betwen colors.
For setting the Operation Speed you can scroll through SP.0 1 to the highest
speed at Sp.fl (1-100). Press SETUP again to control the Strobe Speed from
f500 to f599.
2. BUILT-IN PROGRAM SELECTION
You can access several levels of programs and different styles by setting
the program number, then pressing SETUP button to select programming
options.
To acces the pre-saved programs, press the MODE button until you
see Pr.0 1. Then use UP or DOWN buttons to choose betwen programs titled
Pr.02 - pr.24. When in the selected program number, pressing SETUP again
allows you to set the Operation Speed. You can scroll through SP.0 1 to the
highest speed at Sp.fl (1-100). Press SETUP again to control the Strobe
Speed from f500 to f599.
The Control Screen with
MENU, SETUP, UP, and
DOWN Navigation buttons.

7
3. DIMMING MODE
Press the MODE button until COLR displays on the Menu screen. Then
repeatedly pressing the SETUP button will scroll through 4 selections,
RED (R), GREEN (G), and BLUE (B). Each of the R, G, and B selections
have 0-255 levels of dimmer.
MENU OPTIONS CONT’D:
4. SOUND MODE - This menu will let you navigate and select your de-
sired Sound Mode settings.
Press the MODE button until SU.20 displays on the Menu screen. The
menu will display the parameters SU.00 - SU.3 1. indicating the level of sen-
sitivity of the Microphone (default is 20). Pressing + or - will allow the user
to set the level of Sound sensitivity of the light xture.
Note that this xture has DMX Auto Detection, so regardless of any other Mode
setting, if there is DMX signal present, it will automatically turn on it’s DMX Mode.
When DMX is no longer present, the xture returns to previous Mode setting
(infrared remote control also disabled when in DMX Mode).
5. DMX MODE
Press the MODE button until d . 001 displays on the Menu screen.
The DMX Channel can be selected by pressing the UP and DOWN buttons
and selecting d . 001 - d . 512 . By default, the xture uses a 2 Channel
Conguration.
More DMX Channel congurations can be used by pressing the SETUP
button and selecting either 2-ch , 3-ch , 7 -ch , or 14-ch , or 26-ch .
The following pages contain Control Charts for each channel mode.
6. MASTER/SLAVE MODE
Press the MODE button until SLAV displays on the Menu screen. The xture
will be slaved to which ever lead device is being controlled. Each xture
acts as a Master when not in Slave Mode.

8
SLAVE MODE MENU MAP
8. RESTORE FACTORY SETTINGS
When xture is off, press the MODE and SETUP buttons at the same time
and hold while turning the xture power on. Hold the buttons until rSEt
displays and ashes on the Menu screen.
7. SLAVE MODE MENU OPTIONS
This MENU MAP details DMX setting options to access preset programs.

9
DMX CHANNEL MODES SETUP

10
DMX CHANNEL MODES SETUP

11
DMX SETUP CONTROL:
[To make Terminator; solder a 120 resistor between
Signal (–) and Signal (+) into a 3-pin XLR-plug and
plug it in the DMX-output of the last xture.]
NOTE: The last or nal xture in the DMX chain MUST have a terminator
plug. A terminator is an XLR type plug that does not connect to a cable.
Assembling a DMX Chain is as simple as connecting two more more
xtures with DMX In/Outs with the proper DMX specic 3-pin XLR-style
cables.
MAKE A TERMINATOR:

12
DMX SETUP:

13
CARE:

14
BLACK OUT All LEDs to On or Off state
AUTO Auto/Demo Mode
SOUND Sound Reactive Settings
STROBE Flash On/Off and Freq. Settings
SPEED Rate at which Colors Change
SENSITITY Level of Sound Reactivity
%Used for the Dimming Percentage
MANUAL Sets Manual Color Mode
FADE | SNAP Fades to Next Color, or Black
+ / - Increase or Decrease Selection
As described earlier in this manual, AUTO and SOUND modes are selected
and then navigated with the + or - buttons to make program selection.
Selecting STROBE, SPEED, or SENSITIVITY while the light is in AUTO or
SOUND Modes will adjust those settings under the currently chosen Preset
Program.
The % button is used to set the dimming level of the selected color, usually
used with a MANUAL button sequence.
Pressing the MANUAL button and a sequence of numbers will select various
settings. These are described on the next page.
FADE/SNAP allows the user to force a color change, but as a fade effect.
IR REMOTE CONTROL:
9. INFRARED REMOTE OPTIONS
Your xture comes with an Infrared Remote Control. This requires aim-
ing the remote forward and at the face of the light in order to send it your
selections.
The remote has two sections of control, settings and colors. Each has
the associated selection the light will enter upon pressing. They are
described here:

15
IR REMOTE CONTROL:
On Buttons 0-9, the LEDs will display the associated colors when select-
ed.
0123456789
White Red Amber Yellow1 Green Cyan Blue Purple Pink Yellow2
DIMMING MODE
By selecting MANUAL and then a Color Button labeled with either R, G,
or B, you can create your own color mix by increasing or decreasing the
value of that single color. These buttons are outlined on the remote in the
form of an upside-down “T” shaped box. Pressing + or - will increase the
brightness.
Press the button “MANUAL”, then press down “R”, “G” or “B” or “2” to
enter dimming mode. Press “0”~“9” buttons in turn, enter a number value
between 0-100. Press the “%” button again, to conrm the number is the
percentage of the color. For example, press the “MANUAL” + “R” + “5” +
“0” + “%” in turn, set the red LED brightness is on at 50%.
NOTE
The numbered buttons are used as the number, like “2”, or a color like “Am-
ber” allows the buttons to have two functions. Press the “MANUAL” button
and next press a number button, it is only equivalent to it’s color, like “Amber”.
If press “2” button in other time, is equivalent to press “2” numeric button. For
example: Press the “MANUAL” + “2” + “5” + “0” + “%” in turn, set the Amber
led brightness is 50% dimmed.
10. RESTORE FACTORY SETTINGS
Pressing BLACK OUT, then 9, 8, and 7 will reset the xture to default
factory settings.

(NO DIRECT SALES, DEALERS AND DISTRIBUTORS ONLY)
Please Register your product warranty on ProXDirect.com,
submit your testimonials and setup photos to our website,
& Tag us on your social media websites.
#proxdirect