Xtrails ADPRO iFT Assembly instructions

ADPROiFTSeries
HardwareInstallationManual
March2017
Doc.27817_05
FirmwareversionXO4.00

ADPRO iFT Series Hardware Installation Manual
27817_05 3
Disclaimer
Thecontentsofthisdocumentareprovidedonan"asis"basis.Norepresentationorwarranty(eitherexpressorimplied)ismadeastothecompleteness,
accuracyorreliabilityofthecontentsofthisdocument.Themanufacturerreservestherighttochangedesignsorspecificationswithoutobligationandwithout
furthernotice.Exceptasotherwiseprovided,allwarranties,expressorimplied,includingwithoutlimitationanyimpliedwarrantiesofmerchantabilityand
fitnessforaparticularpurposeareexpresslyexcluded.
Intellectual Property and Copyright
Thisdocumentincludesregisteredandunregisteredtrademarks.Alltrademarksdisplayedarethetrademarksoftheirrespectiveowners.Youruseofthis
documentdoesnotconstituteorcreatealicenseoranyotherrighttousethenameand/ortrademarkand/orlabel.Thisdocumentissubjecttocopyrightowned
byXtralis.Youagreenottocopy,communicatetothepublic,adapt,distribute,transfer,sell,modify,orpublishanycontentsofthisdocumentwithoutthe
expresspriorwrittenconsentofXtralis.
Trade Name Statement
Xtralis,theXtralislogo,TheSoonerYouKnow,VESDA-E,VESDA,ICAM,ECO,OSID,HeiTel,ADPRO,IntrusionTrace,LoiterTrace,ClientTrace,
SmokeTrace,XOa,XOh,iTrace,iCommand,iRespond,iCommission,iPIR,andFMSTaretrademarksand/orregisteredtrademarksofXtralisand/orits
subsidiariesintheUnitedStatesand/orothercountries.Otherbrandnamesmentionedhereinareforidentificationpurposesonlyandmaybetrademarksof
theirrespectiveholder(s).
General Warning
Thisproductmustonlybeinstalled,configuredandusedstrictlyinaccordancewiththeGeneralTermsandConditions,UserManualandproductdocuments
availablefromXtralis.Allproperhealthandsafetyprecautionsmustbetakenduringtheinstallation,commissioning,andmaintenanceoftheproduct.The
systemshouldnotbeconnectedtoapowersourceuntilallthecomponentshavebeeninstalled.Propersafetyprecautionsmustbetakenduringtestsand
maintenanceoftheproductswhenthesearestillconnectedtothepowersource.Failuretodosoortamperingwiththeelectronicsinsidetheproductscan
resultinanelectricshockcausinginjuryordeathandmaycauseequipmentdamage.Xtralisisnotresponsibleandcannotbeheldaccountableforanyliability
thatmayariseduetoimproperuseoftheequipmentand/orfailuretotakeproperprecautions.OnlypersonstrainedthroughanXtralisaccreditedtrainingcourse
caninstall,testandmaintainthesystem.
Liability
Youagreetoinstall,configure,andusetheproductsstrictlyinaccordancewiththeUserManualandproductdocumentsavailablefromXtralis.
Xtralisisnotliabletoyouoranyotherpersonforincidental,indirect,orconsequentialloss,expenseordamagesofanykindincludingwithoutlimitation,lossof
business,lossofprofits,orlossofdataarisingoutofyouruseoftheproducts.Withoutlimitingthisgeneraldisclaimerthefollowingspecificwarningsand
disclaimersalsoapply:
Fitness for Purpose
Youagreethatyouhavebeenprovidedwithareasonableopportunitytoappraisetheproductsandhavemadeyourownindependentassessmentofthefitness
orsuitabilityoftheproductsforyourpurpose.Youacknowledgethatyouhavenotreliedonanyoralorwritteninformation,representation,oradvicegivenbyor
onbehalfofXtralisoritsrepresentatives.
Total Liability
Tothefullestextentpermittedbylawthatanylimitationorexclusioncannotapply,thetotalliabilityofXtralisinrelationtotheproductsislimitedto:
i. inthecaseofservices,thecostofhavingtheservicessuppliedagain;or
ii. inthecaseofgoods,thelowestcostofreplacingthegoods,acquiringequivalentgoodsorhavingthegoodsrepaired.
Indemnification
YouagreetofullyindemnifyandholdXtralisharmlessforanyclaim,cost,demand,ordamage(includinglegalcostsonafullindemnitybasis)incurredorwhich
maybeincurredarisingfromyouruseoftheproducts.
Miscellaneous
Ifanyprovisionoutlinedaboveisfoundtobeinvalidorunenforceablebyacourtoflaw,suchinvalidityorunenforceabilitywillnotaffecttheremainderwhichwill
continueinfullforceandeffect.Allrightsnotexpresslygrantedarereserved.
Document Conventions
Thefollowingtypographicconventionsareusedinthisdocument:
Convention Description
Bold Usedtodenote:emphasis.
Usedfornamesofmenus,menuoptions,toolbarbuttons…
Italics Usedtodenotereferencestootherpartsofthisdocumentorotherdocuments.Usedfortheresultofanaction.
Thefollowingiconsareusedinthisdocument:
Icon Description
Note.Thisiconindicatesinformationofspecialinterestthatwillhelpthereadermakefulluseoftheproduct,optimiseperformance,etc.
Failuretoreadthenotewillnotresultinphysicalharmtothereader,ordamagetoequipmentordata.
Caution!Thisiconindicatesdangertoequipment.Thedangercanbelossofdata,physicaldamagetotheequipment,orpermanentcorruption
ofconfigurationdetails.
Warning!Thisiconindicatesdangerofphysicalharmtothereader.Notfollowinginstructionsmayleadtodeathorpermanentinjury.
Warning!Thisiconindicatesdangerofelectricshock.Thismayleadtodeathorpermanentinjury.
Warning!Thisiconindicatesthatthereisadangerofinhalingdangeroussubstances.Thismayleadtodeathorpermanentinjury.

iFT Series Hardware Installation Manual ADPRO
4 27817_05
Contact Us
UK and Europe+441442242330 D-A-CH+49431232841 The Americas+17817402223
Middle East+96265885622 Asia+862152400077 Australia and New Zealand+61399367000
www.xtralis.com
Environmental Information
Thecrossed-outwheeledbinmeansthatwithintheEuropeanUniontheproductmustbetakentoseparatecollectionattheproduct
endoflife.Thisappliestothedevicebutalsotoanyaccessoriesmarkedwiththissymbol.Donotdisposeoftheseproductsas
unsortedmunicipalwaste.
Ifyouneedmoreinformationonthecollection,reuse,andrecyclingsystemspleasecontactyourlocalwasteadministration.Youcan
alsocontactusformoreinformationontheenvironmentalspecificationsofourproducts.

ADPRO iFT Series Hardware Installation Manual
27817_05 5
Contents
1 Technical Specifications 7
2 About the iFT Series 9
2.1 Models 9
2.2 Licenses 9
2.2.1 Overview 9
2.2.2 SystemLicense 10
2.3 Software 10
2.4 PartsInformation 10
3 Hard Disks 11
3.1 RequiredHardDiskCapacity 11
3.2 Adding/ReplacingaHardDisk 11
3.3 ReusingUsedHardDisks 12
3.4 RetrievingHardDiskInformation 12
3.4.1 Usingtheta,smartCommand 12
3.4.2 UsingtheXOClientSoftware 13
3.5 InstallingtheFirstHardDisk 13
3.6 InstallingaSecondHardDisk 16
3.7 InstallingaThirdDiskinaniFTDevice 19
3.8 InstallingaThirdandFourthDiskinaniFT-EDevice 22
3.9 RAID1Support 26
3.9.1 AboutRAID1 26
3.9.2 ActivatingRAID1 26
3.9.3 RetrievingRAID1Information 27
4 Front LED Indicators 28
5 Motherboards 29
5.1 Overview 29
5.2 BIOSSettings 29
5.3 Connectors 29
5.4 ReplacingtheMotherboard 30
5.5 ReplacingtheMotherboardBattery 30
6 Connecting IP Cameras 31
7 Main I/O Card 33
7.1 Features 33
7.2 OverviewofInputsandOutputs 33
7.3 InputCircuits 33
7.4 ConnectingInputsandOutputs 34
7.5 CableStrainRelief 34
7.6 ConfiguringtheMIOCard 35
8 XO I/O Interface USB Modules 36
8.1 AbouttheXOI/OInterfaceUSBModules 36
8.2 LoggingontotheHardwareConfigurationTool 36
8.3 MappingtheXOI/OInterfaceUSBModule 40
9 Net I/O Modules 42
10 Monitor 43
11 Modem 44
12 Audio 45
12.1 AudioIN 45
12.2 AudioOUT(Talkback) 45

iFT Series Hardware Installation Manual ADPRO
6 27817_05
12.2.1 Options 45
12.2.2 SetupforVM22A 46
12.2.3 SetupforVM22E 48
12.2.4 TroubleshootingTalkback 48
12.3 UsingtheAxisIPHornSpeaker 49
13 Connecting PIR Detectors 50
13.1 RequiredPIRFirmware 50
13.2 ConnectingPIRDetectors 50
13.3 PIRAddressRange 50
13.4 DirectConnectiontotheMIOCard 50
13.5 ConnectionviatheUSB-to-RS-4858-ChannelDistributionUnit 52
13.6 ConnectionviatheUSB-to-Serial-PortRS-485Converter 54
13.7 ConnectionviatheIFM-485-STInterfaceModule 54
13.8 ConnectionviaIPModules(PROE-IPM) 54
13.8.1 Summary 54
13.8.2 SettinguptheIPModules 55
13.8.3 ConnectingtheIPModulestothePIRDetectors 59
14 Power Consumption 60
15 Retrieving the IP Address 61
16 Diagnostics 62
16.1 LogFilesandReports 62
16.2 RetrievingLogFiles 62
16.3 RetrievingReports 64
17 Web Pages 66
18 Maintenance 67
19 Full Reset by Flashing the DOM 68
19.1 FlashingtheImageFiletotheDOM 68
19.2 AfteraFullReset 70
20 Product Labelling 71
20.1 ProductNumberStructure 71
20.2 DeclarationofConformity 72
Appendix A – Abbreviations 73

ADPRO iFT Series Hardware Installation Manual
27817_05 7
1 Technical Specifications
Operatingsystem ADPRO®XO™SecurityOperatingSystem,Linuxbased
Videoinput iFT:1–321IPcameras
iFT-E:1–32IPcameras
Videooutput XGA–Multiplematrixtypeviews
Physicaloutput:DVI-IorDP(DisplayPort),DVI-I-to-VGAadapterincluded
Videocompression H.264
Videoresolution UptoHD/MP2resolution
Note
TheXO4softwaresupportsvideorenderingupto6400x6400pixels.
Whenusingsuchhigh-resolutionstreams,donotusemorethan16of
suchstreamsononeXOdevice.
Frames/second FullHD@25/30fps–MPixel:fpsiscameradependent.
Bandwidthcapacity(video) 32x5Mbps
Bandwidthmanagement Configurablevariableorconstantbitrate/Configurablebandwidthlimiter
Audioinput Built-inaudioinputsupported2
Audiooutput Standard1lineleveloutput.Optional:upto1percameraviaaudioswitcher(s).
AudiooutonIPcameras2withONVIFProfileSdriver.
Commandinputs 8inputsonthebox(balanced);+20inputs(balanced)viaXOI/OInterfaceUSB
module.
ViaEthernetI/OmodulewithPoE:upto128(go–nogo).
Relayoutputs 4outputsonthebox(SPDT);+8outputs(SPDT)viaXOI/OInterfaceUSB
module.
ViaEthernetI/OmodulewithPoE:upto128(SPDT).
Webserver XOclient–integratedwebclientapplication(ActiveX)
Ethernet 2x100/1000BASE-T,autodetection,fullduplex,RJ45
Recordingtype Schedule/Detection/Event
IPcameraintegration Brandspecific,Generic,orONVIFProfileS2
Management lWebclientinterface(XOclient)
lADPROVideoCentralPlatinum
lHeiTelEMSManagementSoftware
lthird-partysoftware(SDKavailable)
liOS/AndroidiTraceapp.
Powersupply 100–240VAC,50/60Hz,2.5–1.5A
Note
Youmustconnectthevideosystemtoa100–240VAC/16Amains
outletwithproperearthing,applyingaseparate,locallyapproved
powercord.
Operatingtemperature 5–40°C
1Using32IPchannels/16analyticschannelsontheiFTrequiresanewsystemlicense.SeeField Alert #7 – Upgrading
to 32 Channels (29477).
2Cameradependent.ForanoverviewofcompatibleIPcameras,seetheSupported IP Camera List(26742).

iFT Series Hardware Installation Manual ADPRO
8 27817_05
Humidity 20–93%RH(non-condensing);indooruseonly
Diskcapacity iFT:max.3x10TBSATAharddisks.
iFT-E:max.4x10TBSATAharddisks.
RAID1support(requiresmin.2equalHDDs).
Warranty 2years
Dimensions(WxHxD) 441x88x305mm(17.36"x3.46"x12.00")
Analytics Basicmotiondetection(VMD),camerasabotagedetection.
Upto16(iFT)or32(iFT-E)analyticschannelsforIntrusionTrace™,
LoiterTrace™,andSmokeTrace™
Mobileapps iTrace,iPIR,iCommission,iRespond
Orderinginformation PleasecontactyourlocalXtralisADPROproviderfordetailedproduct
information.

ADPRO iFT Series Hardware Installation Manual
27817_05 9
2 About the iFT Series
Note
YoucanfindthelatestversionsofthisdocumentandanyreferenceddocumentontheXtralisSecurity
SolutionsSupportsitewww.xtralissecurity.com(logonmayberequired).Ifadocumentnumberis
indicated(betweenparentheses),youcanenteritintheKeywordsboxonthesite,andsearchforthe
document.
2.1 Models
TheiFTSeriescurrentlyconsistsofthefollowingmodels:
liFT:upto32IPchannelsandupto16analyticschannelsviatrade-off
liFT-E:upto32IPchannelsand32analyticschannels.
OntheiFTmodel,youtradein1videochannelfor1analyticchannel.Thismeans,forexample,thatifyouneed
1analyticchannel,youcanusemaximum31(=32–1)videochannels.Ifyouneed2analyticchannels,youcan
use30videochannels,andsoon.AfullyequippediFTcanusemaximum16analyticchannelswith16(=32-16)
videochannels.
Foroptimalperformance,disablethemonitoroutputwhenusingmorethan16IPchannelsonaniFT.
Note
ThemostrecentiFTmodelscomewithasystemlicensethatsupports32IPchannels.Thesystem
licenseinoldersystemssupportsonly16IPchannels.Youcanupgradeyoursystemlicense,freeof
charge,usingXchange.Forinstructions,seeField Alert #7 – Upgrading to 32 Channels(29477).
Note
WhereverXO deviceismentionedinthisdocument,itappliestoallthedevicesabove(includingthe
obsoletemodels),unlessspecificallymentionedotherwise.
Multi-siteconfigurationispossible:
lIntegrationofupto10000XOdevices
lRemotevideoandaudio,livevideo,andconsultationofrecordings
lCompatiblewithPresidium,S3100,VCP,andM3000
lSDKforthird-partyintegration.
2.2 Licenses
2.2.1 Overview
AllXOdevicesrequirelicenses:
lSystemlicense
lIPvideochannellicenses
l(Optional)PIRinterfacelicense(PIR-HLI)
l(Optional)Analyticapplicationlicenses:IntrusionTrace,LoiterTrace,andSmokeTrace.

iFT Series Hardware Installation Manual ADPRO
10 27817_05
2.2.2 System License
Thesystemlicensedefinesthemaximumnumberofvideochannelsallowed,andthemaximumnumberof
analyticchannelsallowedonyoursystem.
Note
ThesystemlicenseislockedontheXOdevice’smotherboardandisthereforesystemspecific:the
licensehastoincludethecorrectMACaddress.Youcannottransferasystemlicensefromone
devicetoanother.
Formoreinformationonlicenses,seetheXO Client Software User Manual(21796)andtheXchange Tool User
Manual(27816).
2.3 Software
XtralisregularlyprovidessoftwareupdatesforyourXOdevice,whichyoucaneasilydownloadandinstallviathe
Xchangetool.Formoreinformation,seetheXchange Tool User Manual(27816).
Caution!
Xtralisissuesupgradeinformationwitheverymajorsoftwareupgrade.Upgradeinformationmay
consistofsystemrequirements,specialupgradeinstructions,etc.Beforeinstallingnewsoftware,
makesurethatyouread and understand the upgrade information first.Alwaysfollowthe
instructionsintheupgradedocumentation.Ifinanydoubt,donotinstallthenewsoftware.
YoucanfindupgradeinstructionsontheXtralisSecuritySupportsitewww.xtralissecurity.com(listed
underFieldAlerts).AlsochecktheReleaseNotes(listedunderProductRelease)forinformationon
solvedbugsorknownissues.
2.4 Parts Information
Pleaseusethereferencenumbersinthisdocument(forexample#17434080)fororderingpartswithXtralis,orfor
identifyingthecorrectrequiredpart.Ifapartisindicatedbyareferencenumberendinginanasterisk(forexample
#1729121*),thisindicatesthatseveralvariantsexistforthepart(forexamplereferencenumbers#17291210and
#17291211).Thesevariantsareinterchangeable.Anyvariantissuitableforthetaskdescribed.

ADPRO iFT Series Hardware Installation Manual
27817_05 11
3 Hard Disks
3.1 Required Hard Disk Capacity
Astherearemanyconfigurationpossibilities,Xtralishasaharddiskspacecalculatoravailable.Youcanfindthis
harddiskspacecalculatorontheXtralisSecuritySolutionsSupportsitewww.xtralissecurity.com(logon
required).Searchforkeyword‘calculator’.
Note
Thecalculatorisanestimatingtoolonly.Figuresarepurelyindicative.Therealrequirementsofthe
harddiskcapacitydependonscenecontent.
WithfirmwareXO4andabove,youcanspecifyaminimumnumberofdaystokeeprecordingsonthe
harddisks.ThesystemwillcalculateifthereissufficientspaceontheharddisksintheXOdevice,
anditwillactivatesysteminput0050–[SYST]–STORAGEINSUFFICIENTifthisisnotthecase.
Thesystemcalculatestherequiredharddiskspacebasedonthepastrecordings.Fordetails,seethe
XO Client Software User Manual(21796).
TheiFTSeriesdevicesarestandarddeliveredwithout,orwith1harddiskinside.Youcaninstall:
lIntheiFTmodel:
omaximum2harddisksinmodelswithoutextramountingholesintherear
omaximum3harddisksinmodelswithtwoextramountingholesintherear.ThelabelsonthesuitableiFT
devicesindicate‘3HDDReady’.
lIntheiFT-Emodel:
oModelnumbers61xxxxxx:maximum2harddisks.
oModelnumbers63xxxxxx:maximum4harddisks.
3.2 Adding/Replacing a Hard Disk
Ifthesystemisrunningoutofdiskspace,youcanaddanewharddiskwithoutremovinganyoftheharddisksin
use.
IfyoureceiveerrormessagesfromyourharddiskintheStatus screenoftheXOclient,youmayneedtoreplace
thefaultyharddisk.
UsethesereferencenumberstoplaceyourorderwithXtralis:
HDD capacity Reference number
Disk only Disk with mounting kit for ADPRO device
1TB 19150240 39544250
2TB 19150250 39544260
4TB 19150270 39544262
6TB 19150280 39544263

iFT Series Hardware Installation Manual ADPRO
12 27817_05
HDD capacity Reference number
Disk only Disk with mounting kit for ADPRO device
8TB 19150290 39544264
10TB 19150300 39544266
Note
Notallharddisksarecompatiblewithallfirmwareversions.Upgradeyourdevicetofirmwareversion
XOa3.02.0033oraboveforfullcompatibility.
3.3 Reusing Used Hard Disks
Itispossibletomountaharddiskcomingfromanotherdeviceintoanewdevice.However,youmustformat the
used hard disk toerasealldataonthedisktopreventanyconflictsordatadamage.Inaddition,ifyouinstalla
useddiskinanXOdevicethatrunsfirmwareversionXOa3.00orabove,thesystemmayenterthehard disk
lockdown mode:recordingisthennotpossible.Thefollowingmessagewillappear:
Ifyouwanttoinstalladiskfromanotherdevice,andyouneedtorecovertherecordingsthatareontheuseddisk,
followtheinstructionsintheTechTipRecovering Recordings from Used HDDs(29160).
3.4 Retrieving Hard Disk Information
YoucanretrieveharddiskinformationandidentifypossiblyfaultyharddisksusingtheTelnetta,smartcommand,
orusingtheXOclientsoftware.
3.4.1 Using the ta,smart Command
SMARTstandsforSelf-MonitoringAnalysisandReportingTechnology.Executetheta,smart commandina
TelnetsessiontoobtaintheSMARTinformationforallharddisksintheXOdevice.
Thescreendisplaysthefollowinginformation:
Item Description
Device Devicenameoftheharddisk(Linux).
Power status Thepowerstatuscolumndisplaysoneofthefollowingstatuses:
lERROR:thereisaproblemretrievingthepowerstatusofthedrive
lACTIVE/IDLE:driveoperatesnormally
lSTANDBY:driveisinlowpowermode(driveisinspin-downstatus)
lSLEEPING:driveisinlowestpowermode(driveiscompletelyshutdown).

ADPRO iFT Series Hardware Installation Manual
27817_05 13
Item Description
Smart status Thesmartstatuscolumndisplaysoneofthefollowingstatutes:
lERROR:driveisfailing
lALERT:thereisaproblemretrievingSMARTinfofromthedrive,orthedrivemaybe
intheprocessoffailing
lNORMAL:noproblemsfoundwiththedrive.
Temperature Thetemperaturecolumndisplaysfromlefttoright:
ltheminimumtemperatureofthedisk
lthecurrenttemperatureofthedisk
lthemaximumtemperatureofthedisk.
Force lON:SMARTischeckedondiskinSTANDBYorSLEEPINGmode.
lOFF:SMARTisonlycheckedondisksinACTIVE/IDLEmode.
Interval Indicatestheinterval(inminutes)betweenSMARTchecks.
Temperature
threshold
Ifthedisktemperatureishigherthanthetemperaturethreshold,thesystemactivates
systeminput0102–[SYST]–SMARTHDDALERTTEMP.
3.4.2 Using the XO Client Software
Toobtaintoobtainthe(SMART)informationforallharddisksintheXOdeviceintheXOclient,chooseSystem
>Maintenance >Harddisks.TheSmart columnshowstheoperationalstatusoftheharddisks;theTemp
columnindicatesthetemperature.
3.5 Installing the First Hard Disk
Note
Ifyouneedtoinstall2harddisks,followtheinstructionsinInstalling a Second Hard Diskonpage16
instead.
Materialrequiredforthefirstharddisk:
Part Amount + reference number
Diskscrews 4x#17434080
SATAcable 1x#16520877
Caution!
lBeforeinstallingharddisks,stopthedevice.Switchitoffandunplugthepowercord.
lTakeallnecessaryprecautionstopreventstaticdischargesthatmaydamagethedevice:usean
anti-staticwristband,ananti-staticmat…
lTheprocedurebelowassumesthatyouareusinganew disk,or,incaseofauseddisk,thatyou
willformat the used disk anderaseallrecordingsonit.Ifyouwanttoinstallausedharddisk
whilekeepingtherecordingsonit,followtheinstructionsintheTechTipRecovering Recordings
from Used HDDs(29160).

iFT Series Hardware Installation Manual ADPRO
14 27817_05
Toinstallthefirstharddisk,proceedasfollows:
1. Stopthedevice,switchoffthepowersupply,andthenremovethetopcover:unscrew2screwsatthefront,
4atthetop,and3attheback.

2. Fixtheharddisktothebottomofthecasing.
Caution!
Ifyoutiltthecasing,restitcarefullyonthesides,butnotontheback.Youmaydamagethe
connectorsifyoudo.
Dependingontheavailableholesinthecasingandtheharddisk,thefollowingoptionsexist:
oCasingwith6 screw holes inthebottom:usethefirst4holes,ortheouter4holeswith4diskscrews
(#17434080):
oOldcasingwith4 screw holes inthebottom:use4oronly2diskscrews(#17434080):

ADPRO iFT Series Hardware Installation Manual
27817_05 15
3. Connecttheharddisktothepowersupply.
4. ConnectthedisktotheSATA1connectoronthemotherboardwiththeSATAcable(#16520877).

Caution!
DonotbendtheSATAcablestoosharplytopreventcabledamage.
5. IftheSATAcablesdonothavealockingmechanism,usetie-wrapstosecurethecablesonthedisk(s)in
thefollowingway:

6. Ifthereareunusedcablesleft,bundlethemwithtie-wraps.
7. Placethetopcoverback:fixitwith2screwsatthefront,4atthetop,and3attheback.

iFT Series Hardware Installation Manual ADPRO
16 27817_05
8. Connectamonitor/screenandkeyboardtothedevice.Switchonthepowersupplyandwaitfortheboot
windowtoappear.
9. SelectXO Installer andpressEnter.
Note
Thebootwindowonlyappearsforafewseconds,thenthedevicecontinuesbooting.Tomake
surethatyoudonotmissit,pressthearrowkeysonthekeyboardrepeatedlywhilethedeviceis
booting.Thedevicewillthenstopatthebootwindow,andthisgivesyoutimetoselectandopen
theXO Installer menu.
10. ChooseUpdate current system >Manage recording disks.
11. SelectthenewlyinstalledharddiskinthelistandpressEnter.
12. ChooseFormat and use selected disks (usingthetabkey).Thesystemformatstheselectedharddisk.
13. Whenformattingisfinished,chooseMain Menu,andthenchooseReboot.
Thedevicenowrestarts.Afterrestarting,theinstalledharddiskisreadyforuse.
3.6 Installing a Second Hard Disk
Materialrequiredforthesecondharddisk:
Part Amount + reference number
Diskscrews 8x#17434080
SATAcable 1x#16520877
iFT(-E)HDDbracket 1x#17011890
iFT(-E)HDDbracket,L-shaped11x#17011895
Caution!
lBeforeinstallingharddisks,stopthedevice.Switchitoffandunplugthepowercord.
lTakeallnecessaryprecautionstopreventstaticdischargesthatmaydamagethedevice:usean
anti-staticwristband,ananti-staticmat…
lTheprocedurebelowassumesthatyouareusinganew disk,or,incaseofauseddisk,thatyou
willformat the used disk anderaseallrecordingsonit.Ifyouwanttoinstallausedharddisk
whilekeepingtherecordingsonit,followtheinstructionsintheTechTipRecovering Recordings
from Used HDDs(29160).
Toinstallasecondharddisk,proceedasfollows:
1. Stopthedevice,switchoffthepowersupply,andthenremovethetopcover:unscrew2screwsatthefront,
4atthetop,and3attheback.

2. Ifthefirstdiskisalreadyinstalled,youhavetoremoveitfirst:unplugitspoweranddatacables,and
unscrewitfromthebottomofthecasing.
1TheL-shapedbracketisrequiredifyouinstallmorethan2disks.Ifyouwilluseonly2disks,youcanuse2‘flat’HDD
brackets(#17011890).

ADPRO iFT Series Hardware Installation Manual
27817_05 17
Caution!
Ifyoutiltthecasing,restitcarefullyonthesides,butnotontheback.Youmaydamagethe
connectorsifyoudo.
3. Fixthefirstandsecondharddisktogetherusingthe2harddiskbrackets(#17011890and#17011895)and
8screws(#17434080)asshownbelow.Makesurethatthemountingscrewholesonharddisk1areonthe
outside.

A:bracket#17011890;B:L-shapedbracket#17011895
4. Fixharddisk1tothebottomofthecasing.Forinstructionsdependingonthemodelandharddiskcapacity,
seeInstalling the First Hard Disk,step2onpage14.
5. Connectharddisk1tothepowersupply,andtotheSATA1connectoronthemotherboardwiththeSATA
cable(#16520877).


iFT Series Hardware Installation Manual ADPRO
18 27817_05
6. Connectharddisk2tothepowersupply,andtotheSATA2connectoronthemotherboardwiththeSATA
cable(#16520877).

Caution!
DonotbendtheSATAcablestoosharplytopreventcabledamage.
ThetablebelowliststhecorrectdevicesandSATAconnectors:
Device SATA connector
DOM SATA0
HDD1 SATA1
HDD2 SATA2
7. IftheSATAcablesdonothavealockingmechanism,usetie-wrapstosecurethecablesonthedisk(s)in
thefollowingway:

8. Ifthereareunusedcablesleft,bundlethemwithtie-wraps.

ADPRO iFT Series Hardware Installation Manual
27817_05 19
9. Placethetopcoverback:fixitwith2screwsatthefront,4atthetop,and3attheback.
10. Connectamonitor/screenandkeyboardtothedevice.Switchonthepowersupplyandwaitfortheboot
windowtoappear.
11. SelectXO Installer andpressEnter.
Note
Thebootwindowonlyappearsforafewseconds,thenthedevicecontinuesbooting.Tomake
surethatyoudonotmissit,pressthearrowkeysonthekeyboardrepeatedlywhilethedeviceis
booting.Thedevicewillthenstopatthebootwindow,andthisgivesyoutimetoselectandopen
theXO Installer menu.
12. ChooseUpdate current system >Manage recording disks.
13. Selectthenewlyinstalledharddisk(s)inthelistandpressEnter.
14. ChooseFormat and use selected disks (usingthetabkey).Thesystemformatstheselectedharddisks.
15. Whenformattingisfinished,chooseMain Menu,andthenchooseReboot.
Thedevicenowrestarts.Afterrestarting,theinstalledharddisksarereadyforuse.
3.7 Installing a Third Disk in an iFT Device
Materialrequiredforthethirdharddisk:
Part Amount + reference number
Diskscrews 4x#17434080
SATAcable 1x#16520877
iFT(-E)HDD3+4bracket 1x#17011920
Self-tappingscrews3.5x6.5mm 3x#17362010
YcableSATAto2xSATA 1x#16520795
Note
InstallingathirddiskisonlypossibleiniFTdeviceswithmodelsthathavetwoextramountingholesin
therear.ThelabelsonthesuitableiFTdevicesindicate‘3HDDReady’.
ForinstallingathirddiskinaniFT-Edevice,seeInstalling a Third and Fourth Disk in an iFT-E Device
onpage22instead.

iFT Series Hardware Installation Manual ADPRO
20 27817_05
Caution!
lBeforeinstallingharddisks,stopthedevice.Switchitoffandunplugthepowercord.
lTakeallnecessaryprecautionstopreventstaticdischargesthatmaydamagethedevice:usean
anti-staticwristband,ananti-staticmat…
lTheprocedurebelowassumesthatyouareusinganew disk,or,incaseofauseddisk,thatyou
willformat the used disk anderaseallrecordingsonit.Ifyouwanttoinstallausedharddisk
whilekeepingtherecordingsonit,followtheinstructionsintheTechTipRecovering Recordings
from Used HDDs(29160).
ToinstallathirdharddiskinaniFTdevice,proceedasfollows:
1. Stopthedevice,switchoffthepowersupply,andthenremovethetopcover:unscrew2screwsatthefront,
4atthetop,and3attheback.

2. Fixthethirddiskonthemountingbracket(#17011920)using4diskscrews(#17434080).Makesurethatthe
diskisonthecorrectsideasshownintheimagebelow.

3. BeforemountingthebracketwiththediskintheXOdevice,arrangetherequiredSATApoweranddata
cablessothatyoucanaccessthemwhenthebracketisinplace.