Xtreme Signal HDB91X Setup guide

180 DAY LIMITED WARRANTY
Don’t forget to Scan for Channels
For Troubleshooting, Videos and Tips Go To:
www.XtremeSignal.com/hdb91x
Auto Scan or Channel Scan is a necessary
process that you must run on your HDTV or
converter box before you start receiving
channels.
Make sure you are scanning for TV
Antenna (ATSC) and NOT Cable TV (QAM).
Scanning for cable stations will bring up
partial or no channel list.
MENU
- SETTINGS
- CHANNELS
- SCAN FOR CHANNELS
www.xtremesignal.com Tel [phone]
by Solid Signal
CALL SOLID SIGNAL FOR SUPPORT
HDB91X
1.877.697.4462
Assembly and Installation Manual
What’s Included
Xtreme Series HD Antenna
Regardless of where you bought this antenna
www.XtremeSignal.com
www.xtremesignal.com Tel [phone]
(1) Dipole
(1) Mounting
(3) Sections of Antenna Boom
Small hardware such as wing-nuts and clamps
are also included but come already attached.
(1) Mast Clamp
by Solid Signal
This Xtreme Signal product is hereby warrantied against defects arising from faults in materials or workmanship for a period of 180 (one
hundred and eighty) days starting from the original date of purchase. Neither Solid Signal, Xtreme Signal, nor Signal Group LLC will
honor a warranty claim unless accompanied by original proof of purchase. All warranty claims must be made to a Solid Signal authorized
dealer or directly to Solid Signal. In the case that the dealer involved in the purchase of your antenna is unavailable or unknown, contact
Solid Signal at 25225 Regency Drive, Novi MI 48375, either by phone at 877.697.4462 or via [email protected]om.
This product warranty covers only the parts originally included in the package and includes neither the cost of shipping, removal or
installation, nor any parts purchased ancillary to this sale for the purpose of installation. If this product is damaged or fails in an any way
due to having been improperly installed, abused or neglected or due to any accidental or intentional tampering with the product as
manufactured, this warranty shall be void. If this product is damaged due to acts of nature or corrosion caused by environmental factors
(such as salt spray or acid rain) this warranty shall be void.
Should this product require warranty replacement, the customer shall be responsible for all shipping and handling charges required to
return the product to a Solid Signal dealer. At its option, Solid Signal or a Solid Signal authorized dealer shall repair or replace this
product and return it to the customer with no additional freight charges due.
This warranty policy is the sole warranty for this product. Neither Solid Signal nor its authorized dealers shall be responsible for
enforcement of any other warranty either express or implied made by any other entity. Express, Implied, or Statutory Warranties
including warranties of tness to a particular purpose or merchantability are limited to this single 180-day warranty. This warranty is the
sole and exclusive remedy for any customer, whether in contract, tort, or otherwise. Neither Solid Signal nor its authorized dealers shall
be liable for any damage or loss, whether incidental or consequential, except as set forth above. Commercial loss shall not be covered
except as set forth above.
This warranty is enforceable to the extent that it is not superseded by local or state law. Consult with local authorities for any specic
legal rights which may apply to your jurisdiction.

ASSEMBLY INSTRUCTIONS
Unfold elements by rotating them forward until
they snap into place.
Attach the three sections of antenna with the
brace and wing-nuts that come already
Next, the dipole is attached by wing-nut and
bolt to the antenna before the rst set of
Next clamp on the mounting brace by lining it
up with the designated holes on the boom.
Having trouble?
The U-bolt and clamp are used to tighten
mounting hardware to a mast that is up to 2”
Outer diameter. Adjust angle if needed.
Insert the reectors into the brace and secure
tightly with wing-nut and bolt.
Or go to www.xtremesignal.com/hdb91x
Watch a Video of the assembly
by scanning this QR Code
www.xtremesignal.com
Tel [phone]
Antenna Placement for Best Signal
TV Transmitters
Back of Antenna
Antennas work o of line of sight, so to get the best performance place the antenna
where it has a clear view. An obstruction like a building or hill immediately in front of
the antenna reduces signal more than a building down the street. Try and avoid placing
the antenna within 3 feet of any metal objects that could interfere with reception.
60°
WARNING
RISK OF ELECTROCUTION
This antenna picks up
approximately 60°
wide out of 360°. Aim
the antenna to face
the center of the
group of stations you
are trying to receive.
If you are having
trouble getting a
particularly weak
channel, you can
try pointing the
directly at the
compass heading.
This information
is available from
sites like
www.antennaweb.org
Every year people are injured or
killed from antennas or masts
making contact with overheard
power lines. Be sure to thor-
oughly check mounting site to
ensure there is no risk of this
antenna touching a power line.
Always be aware, and use caution
when going up on a roof. Besides
the risk of falling, the electrical
shock that comes from contacting
a power line with your antenna or
mast is equal to being struck by a
bolt of lightning
www.xtremesignal.com Tel [phone]
TV Transmitter
If you live in a valley or
have obstructions, try
and put the antenna up
higher to compensate
for signal loss.
Installing an antenna
in the attic makes it
less eective and
may require you to
use a larger antenna
Aiming your Antenna
Being at an elevated
position can be
helpful for antenna
reception.
by Solid Signal