xxter HK01 Series User manual

!
!
!
!
!
!
!
!
!
HK01x!manual!
!
!
!
!
!
!
!
Version!1.0!–!July!2019!
!
©!2015!xxter!bv.!All!rights!reserved.!!
!
More!information!can!be!found!at!www.xxter.com!

HK01x!manual!
2!
Contents
!
! !
1.! Connecting!the!device! 3!
2.! Reset!options!and!status!LEDs! 5!
!Technical!specifications! 6!
Welcome
!
With!xxter!you!can!extend!an!automated!home!or!office!in!only!a!few!
steps!and!control!it!with!a!smartphone!or!tablet.!!
!
This!manual!describes!the!connections!and!LED!indicators!of!the!first!
generation!xxter!device,!like!the!HK01E.!
!
For!more!information!about!the!working!and!configuration!options!of!
xxter!an!installation!manual!and!a!user!manual!is!available.!
!
Please!refer!to!www.xxter.com!for!more!information.!
!

HK01x!manual!
3!
1. Connecting the device
!
The!steps!to!connect!the!xxter!device!depend!on!the!model!that!is!used.!
For!all!models!the!UTP!cable!has!to!be!connected!to!the!(internal)!
network.!xxter!has!to!be!able!to!connect!to!the!Internet,!to!download!
the!configuration!and!for!future!firmware!updates.!!
!
KNX$direct$
In!case!you!are!using!an!xxter!model!with!a!direct!KNX-bus!connection!
(HK01!of!HKE01),!then!connect!the!bus!cable!to!pin!2!(KNX!min/black)!
and!pin!3!(KNX!plus/red),!see!image!6.!First!connect!xxter!to!the!KNX-
bus!and!then!connect!xxter’s!power!adaptor!to!the!power!socket.!
!
!
Image$1:$xxter$rear$panel$
$
KNX$connection$over$IP$
When!using!KNX!over!a!KNXnet/IP!module,!please!make!sure!the!xxter!
unit!and!the!KNXnet/IP!module!are!both!connected!to!the!same!
internal!network.!
$
Artnet$DMX$
For!the!use!of!DMX!components,!an!ArtNet->DMX!node!is!required.!
This!node!must!also!be!connected!to!the!same!internal!network!as!the!
xxter!unit.!A!list!of!ArtNet->DMX!nodes!that!are!tested!with!xxter!can!
be!found!on!the!website.!
!
Philips$Hue$
When!using!Philips!Hue,!make!sure!that!the!xxter!unit!and!the!Hue!
network!module!(bridge)!are!both!connected!to!the!same!internal!
network.!

HK01x!manual!
4!
enOcean$
In!case!you!are!using!a!xxter!model!with!enOcean!support!(HE01,!
HCE01!of!HKE01),!then!the!enOcean!antenna!has!to!be!connected!to!
the!serial!port!(RS232)!on!the!front!side!of!the!device!(see!Image!7).!!
!
1) Make!sure!the!power!adaptor!of!xxter!is!not!connected.!
2) Connect!the!serial!connector!of!the!ANE01!to!the!serial!port!
(RS232)!of!the!xxter!unit.!
3) Connect!the!electrical!splitter!cable!to!the!xxter!unit.!
4) Connect!the!power!adaptor!to!the!electrical!splitter!cable.!
!
!
Image$2:$enOcean$connection$schema$
The!enOcean!ANE01!antenna!is!equipped!with!a!repeater!function.!
!
The!ANE01!repeater!has!three!different!settings:!
1) No!repetition!(standard):!both!dip-switches!to!OFF!(numbered!
side)!
2) Repeat!only!original!telegrams!(level!1):!set!only!dip-switch!1!
to!ON!
3) Repeat!both!original!and!one!time!repeated!telegrams:!set!both!
dip-switches!to!ON!
!
Before!a!new!repeater!setting!is!active,!it!is!required!to!shortly!
disconnect!the!ANE01!from!the!power!source.!

HK01x!manual!
5!
2. Reset options and status LEDs
!
In!case!of!any!problems,!the!xxter!device!can!be!reset!in!several!
different!ways,!see!also!image!11:!
!
BUT1 Hold during boot Reset to factory defaults
BUT1 Press shortly Full restart
BUT1 Press long (longer then 3 sec.) Reset to factory defaults
BUT2 Press shortly Reset application (soft restart)$
$
When!the!xxter!device!is!connected!to!power,!the!system!status!can!be!
seen!using!the!LED!indicators:$
$
LED1 green slow flashing Currently booting or shutting down
LED1 green continuous Application started and ready for use
LED2 green slow flashing Normal operation - OK
LED2 yellow slow flashing No connection to KNX or enOcean
LED2 red quick flashing LAN problem, no network
LED2 red / green intermittent No Internet connection, only LAN connection*
*) the Internet connection is only verified during boot and when the “Check Internet connection”
button is pressed on the status page of the xxter device.
!
Image$3:$xxter$rear$panel$

HK01x!manual!
6!
Technical specifications
!
Size!(lxwxh):!180x152x38mm!
Weight:!0,5!kg!
Voltage:!5VDC!
Power!consumption:!300mA!(avg.)!
Cooling:!passive!
!
Accessories:!
-!Adapter!5VDC!
-!UTP!cable!
-!enOcean!antenna!(only!for!models!HE01,!HCE01!en!HKE01)!
-!Installation!manual!EN!
-!User!manual!EN!
!