
11
PSR-E443
Fig.3(図 3)
5. TW Circuit Boards and Speakers (Tweeters)
(Time required: About 3 minutes each)
5-1 Remove the lower case assembly. (See procedure 1.)
5-2 TW Circuit Board (L) and Speaker L (Tweeter)
Remove the connector assembly TW and speaker cable
soldered to the TW circuit board (L) and remove the two
(2) screws marked [380D]. The TW circuit board (L) and
speaker L (tweeter) can then be removed. (Fig.2)
5-3 TW Circuit Board (R) and Speaker R (Tweeter)
Remove the connector assembly TW and speaker cable
soldered to the TW circuit board (R) and remove the two
(2) screws marked [380E]. The TW circuit board (R) and
speaker R (tweeter) can then be removed. (Fig.2)
6. SP Grille L assembly, SP Grille R assembly
(Time required: About 3 minutes each)
6-1 Remove the lower case assembly. (See procedure 1.)
6-2 Set the six (6) hooks [A] parallel to the groove in the
upper case assembly and remove the SP grille L assembly.
(Fig.1, Fig.2)
* The SP grille R assembly can be removed in the
same manner.
7. Lower Key Bed Assembly
(Time required: About 3 minutes)
7-1 Remove the lower case assembly. (See procedure 1.)
7-2 Remove the two (2) screws marked [80] and the screw
marked [100]. The lower key bed assembly can then be
removed. (Fig.2)
8. DMLCD Circuit Board
(Time required: About 5 minutes)
8-1 Remove the lower case assembly. (See procedure 1.)
8-2 Remove the AMJK circuit board.(See procedure 2.)
8-3 Remove the fourteen (14) screws marked [380F]. The
DMLCD circuit board can then be removed. (Fig.5)
* When installing the DMLCD circuit board, tighten
the screws 1 through 4 in numerical order. (Fig.5)
* If the DMLCD circuit board is replaced, execute
the "Factory Set" in the test program.
5. TW シート、スピーカ(ツイーター)
(所要時間 :各約 3 分)
5-1 下ケース Ass'y を外します。(1 項参照)
5-2 TW シート(左)、スピーカ(ツイーター)左
TW シート(左)に半田付けされている TW 束線
とスピーカ束線を外し、[380D] のネジ 2 本を外して
TW シート(左)とスピーカ(ツイーター)左を
外します。(図 2)
5-3 TW シート(右)、スピーカ(ツイーター)右
TW シート(右)に半田付けされている TW 束線
とスピーカ束線を外し、[380E] のネジ 2 本を外して
TW シート(右)とスピーカ(ツイーター)右を
外します。(図 2)
6. SP グリル LAss'y、SP グリル RAss'y
(所要時間 :各約 3 分)
6-1 下ケース Ass'y を外します。(1 項参照)
6-2 6 箇所のフック(A)を上ケース Ass'y の溝と平行
にして、SP グリル L を外します。(図 1、図 2)
※ SP グリル R も同じようにして外すことができま
す。
7. 下ケース鍵盤 Ass'y(所要時間 :約 3 分)
7-1 下ケース Ass'y を外します。(1 項参照)
7-2 [80] のネジ 2 本と、[100] のネジ 1 本を外して、下ケー
ス鍵盤 Ass'y を外します。(図 2)
8. DMLCD シート(所要時間 :約5分)
8-1 下ケース Ass'y を外します。(1 項参照)
8-2 AMJK シートを外します。(2 項参照)
8-3 [380F] のネジ 14 本を外して、DMLCD シートを外
します。(図 5)
※ DMLCD シートを取り付けるときは、1 から 4 の順
でネジを締めてください。(図 5)
※ DMLCD シートを交換した場合は、テストプログラ
ムの FactorySet を実行してください。
(1&2'(5.12%
(エンコーダツマミ)
Fig.4(図 4)
92/80(.12%
(Vツマミ)