Yamaha SPM-K1 - Mounting Kit For Speaker User manual

English Français Deutsch Svenska Italiano Español Nederlands 日本語
SPM-K1
WALL MOUNT BRACKET
SUPPORT MURAL
サウンドプロジェクター壁掛け金具
Installation Manual
Manuel d’installation
Installationsanleitung
Instllationsanvisningar
Manuale d’installazione
Manual de instalación
Installatiehandleiding
取付説明書
01EN_SPM-K1_U-cv1.fm Page 1 Wednesday, January 12, 2005 4:23 PM

DIMENSIONS
DIMENSIONS
ABMESSUNGEN
MATTSKISSER
DIMENSIONI
DIMENSIONES
AFMETINGEN
各部の寸法
Large wall mount bracket
Grand support mural
Große Wandhalterung
Stort väggmonteringsfäste
Staffa di installazione a muro grande
Soporte de montaje en pared grande
Grote wandbevestigingsbeugel
壁掛け金具（大）
Small wall mount bracket
Petit support mural
Kleine Wandhalterung
Litet väggmonteringsfäste
Staffa di installazione a muro piccola
Soporte de montaje en pared pequeño
Kleine wandbevestigingsbeugel
壁掛け金具（小）
Unit with bracket
Le système avec son support
Einheit mit Halterung
Ljudprojektorn med fästet
Unità con staffa
Unidad con ménsula
Toestel met de beugel
取付時の寸法
200
13 8
800
150
187.5 187.5
225 225
262.5 262.5
300 300
150
355 355
385 385
(mm)
1.3kg
50
20
25.2
76
129.5
5
M6TAP
0411134
13
03
125
110
(mm) (mm)
YSP-1
0.1kg ×2
SPM-K1
01EN_SPM-K1_U-cv1.fm Page 2 Wednesday, January 12, 2005 4:23 PM

English
SPM-K1
E-1
WALL MOUNT BRACKET
SPM-K1
Installation Manual
Thank you very much for purchasing the Wall Mount Bracket SPM-K1. Be sure to read this manual thoroughly before
using this bracket. After you have read this manual, retain it for future reference.
SAFETY INSTRUCTIONS
• Always follow the instructions set forth in this manual when installing the Sound Projector using
this bracket.
Improper or inadequate installation could cause the Sound Projector to fall, resulting in personal injury.
• The installation must be secure enough to bear the weight of the Sound Projector, the wall bracket
and other hardware indefinitely, and must also be secure enough to withstand vibrations.
Improper or inadequate installation could cause the Sound Projector to fall, resulting in personal injury.
• To ensure safety, all screws must be tightened securely.
Loose screws could cause the Sound Projector to fall, resulting in personal injury.
• Make sure to leave adequate ventilation space around the unit to allow heat generated by the
Sound Projector to dissipate.
Failure to provide adequate space around the unit could cause the Sound Projector to overheat internally, resulting in
a fire.
• Never hang from the Sound Projector or the wall bracket.
Hanging from the Sound Projector or the wall bracket could cause the Sound Projector or the wall bracket to fall,
resulting in personal injury.
• Once the Sound Projector is installed, safety checks should be conducted on a regular basis.
If the Sound Projector is used over an extended period of time, screws can become loose and the installation can
become weaker due to the passage of time, vibrations, etc.
When installing the Sound Projector using this bracket, all installation work must be performed by
a qualified contractor or dealer personnel. The customer must never attempt to perform this
installation work. Improper or inadequate installation could cause the Sound Projector to fall,
resulting in personal injury.
01EN_SPM-K1_U.book Page 1 Friday, March 25, 2005 1:51 PM

ACCESSORIES
E-2
Check that all of the following parts are included.
Prepare more than six sets of commercially available screws (M5-M6, 25 mm or more in length) and
washers in addition to the accessories shown above.
ACCESSORIES
Small wall mount brackets (2) Projector mounting screws
(M6 x 16) (6)
Safety wires (2) M4 x 10 Screws (2)
Length 300mm
Large wall mount bracket (1)
01EN_SPM-K1_U.book Page 2 Friday, March 25, 2005 1:51 PM

English
INSTALLATION PROCEDURE
E-3
Make sure to leave adequate ventilation space around the unit and follow the instructions below.
In order to secure the unit to the wall, you will need to attach the bracket to the wall first in a manner befitting the
structure and quality of the wall.
Choose a location where the wall can bear the weight of the whole unit.
Before installing the bracket, make sure of the size (see “DIMENSIONS” on the first page of this manual).
Choose a secure wall or beam to fasten the screws. Do not install them into walls mafe of weak
material that can easily come off, such as mortar or plywood wall panels. Loose screws could cause
the projector to fall, resulting in personal injury.
Choose a method (A or B) when attaching the safety wire. When you choose the method A, attach the safety wire using
M4 screws provided. (Some of the projectors have no screw hole depending on the date of manufacture.)
When attaching to the projector. When attaching to the small wall mount
bracket.
If you tighten the screws on the slant, the screw threads in the projector might be broken. Be careful when
using electric tools.
INSTALLATION PROCEDURE
Attach the large wall mount bracket to the wall.
Attach the safety wire.
Washer
(commercially
available)
5~6mm Tapping Screw (commercially available)
In order to secure the unit to the wall, attach four (or more) tapping
screws using the outside of the holes in the wall mount bracket.
Installing into a dry
wall.
Installing directly
into a wall, etc..
25mm or more 25mm or more
Beam, etc. Dry wall
Safety wire
M4 screw
provided
Attach the
safety wires
to the left and
right sides of
the projector.
Rear panel of
the projector
A B
Installation example
Slip one end
through the loop at
the other end
Slip the safety
wire through a
hole in the
bracket
Repeat the same
procedure for the
other bracket.
01EN_SPM-K1_U.book Page 3 Friday, March 25, 2005 1:51 PM

INSTALLATION PROCEDURE
E-4
Use four of the projector mounting screws (M6 x 16) provided to securely attach the small wall mount brackets (2) to the
rear left and right sides of the Sound Projector.
Fit the mounting guide hooks of the small wall mount brackets attached to the Sound Projector into the holes on the left
and right sides of the large wall mount bracket, then slide the unit to the right.
Hold the projector tight with the both hands when attaching / removing the projector to / from the wall.
Holding the projector loose could cause the projector to fall, resulting in personal injury.
Attach the small wall mount brackets to the Sound Projector.
Mount the projector on the wall.
1
1
2
2
Slide the unit to the
right.
Fit the hook into the
hole.
Rear View
Projector mounting
screws (M6 x 16)
Safety wire (Attached
by the method A)
Attach the brackets to the
rear left and right sides of
the Sound Projector.
Safety wire (Attached
by the method B)
01EN_SPM-K1_U.book Page 4 Friday, March 25, 2005 1:51 PM

INSTALLATION PROCEDURE
E-5
English
Align the holes on the large wall mount bracket with the holes on the bottom of the small wall mount brackets, and then
use two of the projector mounting screws (M6 x 16) provided to secure the unit.
Pass the screws (commercially available) through the loops of the safety wires, then tighten the screws to secure the
safety wires to the wall.
Make sure that the screws are strong enough to bear the weight of the projector and the brackets in case they fall.
Attach the safety wires tight.
Secure the unit.
Bottom View
Sound Projector
Projector mounting screws
(M6 x 16)
Attach the safety wires to the wall.
Secure the safety wire to
the wall.
Washer
(commercially available)
Secure the safety wire
to the wall.
Screw
(commercially available)
01EN_SPM-K1_U.book Page 5 Friday, March 25, 2005 1:51 PM

01EN_SPM-K1_U.book Page 6 Friday, March 25, 2005 1:51 PM

SPM-K1
F-1
Français
Support mural pour système acoustique
SPM-K1
Manuel d’installation
Nous vous remercions d’avoir porté votre choix sur le support mural pour système acoustique SPM-K1. Veuillez prendre
soin de lire attentivement ce manuel avant d’installer ce support. Conservez-le pour référence ultérieure.
INSTRUCTIONS DE SÉCURITÉ
• Respectez les instructions que contient ce manuel et qui concernent l’installation du système
acoustique au moyen de ce support mural.
Une erreur d’installation peut provoquer la chute du système, entraînant des blessures.
• L’installation doit être en mesure de résister, sans limite de durée, au poids du système acoustique,
du support mural et de la quincaillerie; elle doit également s’accommoder, le cas échéant, des
vibrations.
Une erreur d’installation peut provoquer la chute du système, entraînant des blessures.
• Pour garantir la sécurité, toutes les vis doivent être soigneusement serrées.
Un défaut de serrage peut provoquer la chute du système, entraînant des blessures.
• Veillez à ménager un espace suffisant autour du système pour que la chaleur qu’il dégage puisse
se dissiper.
Faute de ménager un espace suffisant autour du système, il pourrait surchauffer, ce qui est susceptible de provoquer un
incendie.
• Ne vous suspendez pas au système, ni au support mural.
En vous suspendant au système ou au support, vous pouvez provoquer la chute du système ou du support, entraînant
des blessures.
• Après installation du système, des vérifications de sécurité doivent être effectuées
périodiquement.
Lorsque le système est utilisé pendant une période prolongée, les vis peuvent se desserrer, en raison de vibrations,
etc., rendant l’installation moins sûre.
L’installation du système acoustique à l’aide de ce support doit être réalisé par un ouvrier compétent
ou un représentant du revendeur. En aucun cas, vous ne devez tenter d’effectuer l’installation par
vous-même. Une erreur d’installation peut provoquer la chute du système, entraînant des blessures.
01FR_SPM-K1_U.book Page 1 Friday, March 25, 2005 3:15 PM

ACCESSOIRES
F-2
Assurez-vous que les pièces suivantes font partie de la fourniture.
Préparez plus de six jeux de vis en vente dans le commerce (M5-M6, 25 mm ou plus de longueur) et de
rondelles en plus des accessoires indiqués ci-dessus.
ACCESSOIRES
Petits supports muraux (2) Vis de fixation du système acoustique
(M6 x 16) (6)
Câbles de sécurité (2) M4 x 10 Vis (2)
Longueur 300mm
Grands supports muraux (1)
01FR_SPM-K1_U.book Page 2 Friday, March 25, 2005 3:15 PM