Yard force LX PS300 User manual

300 W / 600 W PORTABLE POWER STATION/ TRAGBARE POWER
STATION/ GÉNÉRATEUR D’ÉNERGIE PORTABLE
Original Instructions/ Original-Bedienungsanleitung/ Manuel d’origine
GB DE FR
LX PS300/ LX PS600

2
Symbols 03
General safety warnings 06
Description of product 08
Technical data 11
Operation 12
Maintenance and storage 16
Declaration of conformity 18
CONTENT

3
Safety symbols
The purpose of safety symbols is to attract your attention to possible dangers. The
safety symbols and the explanations with them require your careful attention and full
understanding. The symbol warnings do not, by themselves, eliminate any danger. The
instructions and warnings they give are no substitutes for proper accident prevention
measures.
WARNING: Be sure to read and understand all safety instructions in this
operator’s manual, including all safety alert symbols such as “DANGER,”
“WARNING,” and “CAUTION” before using this tool. Failure to follow all
instructions listed below may result in electric shock, re and/or serious personal
injury.
SAFETY ALERT SYMBOL: Indicates DANGER, WARNING, or CAUTION. May
be used in conjunction with other symbols or pictographs.
Symbol meaning
This chapter depicts and describes safety symbols that may appear on this product.
Read, understand and follow all instructions on the machine before attempting to
assemble and operate.
SYMBLOS
GB

4
Read the instructions for use before use!
Batteries contain Li-ion. Do not dispose of waste batteries in domestic waste.
Contact local authority to nd out how to dispose of batteries.
WEEE symbol. Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with your Local
Authority or local store for recycling advice.
Do not throw into water.
Do not throw to re.
Do not subject the battery to strong sunlight over long periods of time. Do
not leave on a heater (max.45°C).
Li-Ion

5
Do not expose to rain or water
The product complies with the applicable European directives and an
evaluation method of conformity for these directives was done.
GB

6
IMPORTANT SAFETY INSTRUCTIONS
WARNING! Keep dry and do not expose to high heat.
WARNING! Never disassemble, puncture, shock, crash, short or incinerate.
WARNING! Recycle and dispose in accordance with local regulation.
When using this product, basic precautions should always be followed, including the
following:
• Please read the instruction manual before using this product.
• To reduce the risk of injury, close supervision is necessary when using this product
near children.
• Do not put ngers, hands or any body part into the product.
• Use of an unrecommended attachment or third-party power station manufacturer
may result in a risk of re, electric shock or injury.
• Do not use a damaged or modied battery pack or appliance.
• Do not operate the power station with a damaged cord, plug or output cable.
• When service or repair is required, do not disassemble the power pack yourself. Take
the unit to a qualied service provider. Incorrect reassembly may result in a risk of
re or electric shock.
• In order to reduce the risk of electric shock when the product fails, disconnect the
portable power station from the power supply before performing any instructive
maintenance operations.
GENERAL SAFETY WARNINGS

7
• Charge the internal battery in a well-ventilated area. Do not restrict ventilation.
• Under harsh conditions, liquid may be ejected from the battery. Avoid contact
with the battery and liquid. If contact accidentally occurs, ush with water. If liquid
contacts eyes, seek additional medical help.
• Do not expose the unit to re or excessive heat.
• Have servicing performed by a qualied repair person only.
SAVE THESE INSTRUCTIONS
USE CARE AND SAFETY GUIDE
Do not throw into water.
Do not throw to re.
Do not subject the battery to strong sunlight over long periods of time. Do not
leave on a heater (max.45°C).
GB

8
ButtonCharging Interface
Output Port
Press the button for 3s to switch ON the device
Press the button to active to AC function
Press the button for 3s to switch on the light, 3
modules selectable.
5521 Charge port
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT
15W
OUTPUT 15W
OUTPUT
PD Type C
DC 5521 Type C
15 W
USB A
15 W
QC USB A
18 W
Car charger
12V 120 W
Pure sine wave, 300 W
230 V -50/60 Hz
LX PS300
DESCRIPTION OF PRODUCT
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT

9
Car charger
13.6V 120W
Pure sine wave, 600W
230V -50/60Hz
Button
Press the button for 3s to switch ON the device
Press the button to active to AC function
Press the button for 3s to switch on the light, 3
modules selectable.
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT
5521 Charge port
Charging Interface
Output Port
DC 5521 PD Type C USB A
15W
Type C
15W
QC USB A
18W
GB
LX PS600
100
%
H
O
U
RS50H
Z
50
000
w
A
C
D
C
U
SB
-
A
O
U
TPU
T

10
DISPLAY
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUTINPUT
Battery Level Indicator ‒Shows the remaining battery percentage. If your battery drops towards 0%, the battery segment on
the screen will begin to blink. When this happens, please charge the device immediately.
Time display:
- Showing the remaining charge time based on the current inlet level.
- Showing the remaining working time base on the current outlet level.
Power indicator:
- Showing current inlet power level.
- Showing current outlet power level.
Function indicator:
- Alternating current output function is actived.
- Direct current function is actived.
Actived when the alternating current output function is actived.
100%
HOURS
50
0 00
w
OUTPUT
0 00
w
INPUT
AC
DC USB- A
50HZ

11
Model LX PS300 LX PS600
Dimension 20x 14 x 17 cm 20.0 x 14.0 x 21.5 cm
Capacity 296 Wh (14.8 V) 518 Wh (25.9 V)
Net weight 3.1kg 4.8kg
Iutput port
DC 5521 10-25 V max 60 W 10-30 V max 120 W
Input/ Output port
PD Type C (1 port) 5-20 V/ 65 W (Output)
5-12 V/ 60 W (Input)
5-20V/ 65 W (Output)
5-12V/ 60 W (Input)
Output port
AC output Pure sine wave, 300 W
230 V -50/60 Hz (2 ports)
Pure sine wave, 600 W total
230 V - 50/60 Hz (2 ports)
Max power devices supported by X-boost 550 W 1200 W
USB-A x1, Type C x1 5 V 15 W Max 5 V 15 W Max
USB-A QC 5-12 V 18 W (1 port) 5-12 V 18 W (1 port)
DC 5521 12 V Max 120 W (1 port) 13.6 V Max 120 W (2 ports)
Car charger 12 V Max 120 W (1 port) 13.6 V Max 120 W (1 port)
GB
TECHNICAL DATA

12
Charing the device
- Charge the device with original adaptor
1. Connect the power plug with the adaptor.
2. Charge the device by inserting the 5521 interface to the port.
NOTE: only use the original charging adaptor!
3. The display will show the current charging status when well
connected.
- Charge the device with Car cigarette lighter
1. Connect the wire with the 12V port in the vehicle.
2. Charge the device by inserting the 5521 interface to the port.
NOTE: only use the original charging adaptor!
3. The display will show the current charging statues when well
connected.
- Charge the device with the solar panel (sold separately)
1. Charge the device by inserting the 5521 interface to the port.
NOTE: please pay an attenion to the inlet limitation of the port
for each model! LX PS300 10-25V max 60W, LX PS600 10-30V
max 120W.
- Charge the device by PD type C port (not in the delivery
box)
Charge the device by connecting with a type C wire to the PD type C
port.
15%
15%
15%
15%
OPERATION
1
1
0
0
0
0
%
%
H
H
O
O
U
U
R
R
S
S
5
5
0
0
H
H
Z
Z
5
5
0
0
0
0
0
0
0
0
w
w
A
A
C
C
D
D
C
C
U
U
S
S
B
B
-
-
A
A
O
O
U
U
T
T
P
P
U
U
T
T
1
1
0
0
0
0
%
%
H
H
O
O
U
U
R
R
S
S
5
5
0
0
H
H
Z
Z
5
5
0
0
0
0
0
0
0
0
w
w
A
A
C
C
D
D
C
C
U
U
S
S
B
B
-
-
A
A
O
O
U
U
T
T
P
P
U
U
T
T
1
1
0
0
0
0
%
%
H
H
O
O
U
U
R
R
S
S
5
5
0
0
H
H
Z
Z
5
5
0
0
0
0
0
0
0
0
w
w
A
A
C
C
D
D
C
C
U
U
S
S
B
B
-
-
A
A
O
O
U
U
T
T
P
P
U
U
T
T
1
1
0
0
0
0
%
%
H
H
O
O
U
U
R
R
S
S
5
5
0
0
H
H
Z
Z
5
5
0
0
0
0
0
0
0
0
w
w
A
A
C
C
D
D
C
C
U
U
S
S
B
B
-
-
A
A
O
O
U
U
T
T
P
P
U
U
T
T

13
To obtain the best life from the battery
1. Never allow the device to completely discharge before recharging. The device should be placed on the charger whenever the battery pack
is noticeably running down or the tool no longer performs a task it previously performed.
2. Avoid conducting short charges. Make sure that the device is fully charged each time by allowing the adaptor to complete its full charging
cycle.
3. Avoid allowing loose items like screws or nails etc. to be stored with device as these or similar items can short the device and cause a re
or explosion.
4. Always unplug the device when not in use and store in a dry and secure place.
5. Avoid charging or storing your device in temperatures below 5°C and above 45°C.
6. After use, allow the device to cool down for approximately 30 minutes before attempting to recharge.
GB

14
100%
HOURS
50
000
w
DC USB-A
OUTPUT
15W
OUTPUT
15W
OUTPUT
100%
HOURS 50HZ
50
000
w
DC USB-A
AC
OUTPUT
3s
Switch ON the device
- Press the button for 3s to switch on the device, DC output will be actived accordingly.
- When the device is powered ON, all the DC ports are ready to use.
Active the AC function
- Press the button, the "AC" mark will light on in the display which means the 2 AC ports are ready to use.
Car charger
12V 120 W

15
Charging cycle and working hours
15x
27x
3.5x
6.5x
5x
8x
16x
28x
4h
7h
4h
7h
50h
82h
16h
32h
LX PS300
LX PS600
5W60W
60W
5W60W
GB
15W
15W
60W
100%
HOURS 50HZ
50
000
w
AC DC USB-A
OUTPUT
1
00
%
H
O
U
RS50H
Z
50
000
w
A
C
D
C
U
SB
-
A
O
U
TPU
T

16
CLEAN
Caution! Protect the product from direct contact with water, and make sure that water doesn't get the opportunity to get in.
• Always clean the product thoroughly after each use with a damp cloth, sponge or brush.
• Avoid oil and grease contamination (especially to gripping parts).
• If contamination should occur, wipe the product with a damp cloth moistened with soapy water.
• Never use aggressive cleaning agents, solvents or chemicals for cleaning. Permanent damage to plastic parts could occur.
STORAGE
• Store the machine out of reach of children.
• Don't store the product in direct sunlight for long periods.
• For safety reasons worn or damaged parts should be replaced.
• Store in the original packaging (if possible) in a clean, dry, dark and frost-free place protected from dust and out of reach of children.
• Cover unit with a suitable protective cover that does not retain moisture. Do not use sheet plastic as a dust cover. A nonporous cover will
trap moisture around the machine, promoting rust and corrosion.
• The ideal storage temperature is between 5 °Cand 30 °C.
DISPOSAL
• Dispose your device, accessories and packaging in accordance with the requirements of environmental protection into the recycling
collection center.
• This machine does not belong to the household waste. Save the environment and take this device to designated collection points where
it will be received for free. For more information please contact your local authority or nearest collection point. Improper disposal may be
punished according to national regulations.
• The battery contains toxic substances. Toxic materiaIs must be disposed of in a specied manner in order to prevent contamination of the
environment. Take used batteries to a recycling center. Do not throw the battery into household waste, re or water.
MAINTENANCE AND STORAGE

17
How do I care for the power station?
This power station is designed for a variety of uses so there is a good chance our device will need a little cleaning every now and then.
Please use a dry, non-abrasive cloth. We like the cleaners that have been designed for mobile phone and computer screens if you need a little
extra oomph. Do not give it a bath!
How do I store the power station?
Please store your power station in a dry environment out of direct elements. For optimal battery health, store the device at room temperature
80% charged. This device offers a water-resistant, dustproof case for maximum protection. We suggest that you keep your connected to a
power source when not in use, like a solar panel or a wall plug, so it keeps its battery healthy and topped over. This prolongs battery life and
will ensure your power station is ready to recharge your gear at all times.
How do I use the power station safely?
Please use the power station in temperature conditions inside of its operating temperature range. Using it outside of its optimal temperature
operating range can push it beyond its safe and effective limits.
Do not submerge your power station. It is not waterproof and this will void your warranty.
Don’t throw the power station around. Treat it like the equipment you are plugging into it, with care.
WARNING! Do not charge the machine immediately after it is fully discharged. For safety, please cool the battery before charging!
GB
MAINTENANCE AND STORAGE

18
To the provisions of Council Directives
We
MEROTEC GmbH
Otto-Brenner-Str. 8
47877 Willich
Germany
Declare that the product:
Machine Description: Power station
LX PS300/ NV300
LX PS600/ NV600
Complies with the essential health and safety requirements of the following directives:
Low Voltage Directive 2014/35/EU
Electromagnetic Compatibility Directive 2014/30/EU
EC Directive 2011/65/EU and its amendment Directive (EU) 2015/863 (RoHS)
Standards and technical specification referred to :
EN 62368-1:2020+A11+2020
EN 55032:2015+A1:2020+A11:2020
EN IEC 61000-3-2:2019+A1:2021
EN 61000-3-3:2013+A1:2019+2019+A2:2021
Authorized Signatory
Date: 04.11.2022
Signature:________________________
Place: Willich
Name: Roland Menken
General Manager
MEROTEC GmbH
Otto-Brenner-Str. 8, 47877 Willich, Germany
DECLARATION OF CONFORMITY

19
GB

20
Symbole 21
Allgemeine Sicherheitswarnhinweise 24
Produktbeschreibung 26
Technische Daten 29
Betrieb 30
Wartung und Lagerung 34
Konformitätserklärung 36
INHALTSVERZEICHNIS