Yardline BRAXTON User manual
16583-P
Call Us First!
DO NOT RETURN TO STORE.
For questions on assembly or for general inquiries, you may contact us in the following ways:
Call customer service: 1-877-743-3400
Did you enjoy building your shed?
JOIN OUR TEAM
AND MAKE UP TO $1,500/WEEK*
o
r
v
i
s
i
t
b
a
c
k
y
a
r
d
i
n
s
t
a
l
l
e
r
.
c
o
m
Flexible schedule No selling,
just building
Bonus incentives
available
S
c
a
n
t
h
e
o
w
c
o
d
e
t
o
a
p
p
l
y
t
o
d
a
y
.
INSTALLERS
WANTED
*based on number of completed installations
Call a Recruiter Today! 734-365-7000
visit us online at
help.backyardproducts.com
AVOID THE WAIT!
Submit a help request
Answers to frequently asked questions
Live chat with an agent
(This page intentionally left blank.)
***CONTACT OUR CUSTOMER SERVICE TEAM
IF ANY PARTS ARE MISSING OR DAMAGED***
BEFORE YOU BEGIN
IMPORTANT!
READ INSTRUCTIONS THOROUGHLY PRIOR TO BEGINNING ASSEMBLY.
• BUILDING RESTRICTIONS AND APPROVALS
Be sure to check with local building department and homeowners association for specic restrictions and/ or requirements before building.
• ENGINEERED DRAWINGS
Contact our Customer Service Team if engineered drawings are needed to pull local permits.
• SURFACE PREPARATION
To ensure proper assembly you must build your shed on a level surface.
Recommended methods and materials to level your shed are listed on page 7.
• CHECK ALL PARTS
Inventory all parts listed on pages 14 - 16.
• ADDITIONAL MATERIALS
You will need additional materials to complete your shed. See pages 4 - 5 for required and optional materials and quantities.
07/11/2019
BRAXTON 12' x 24' (365,7 x 731,5 cm)
ASSEMBLY MANUAL 16583-P
A Backyard Products Company
KEEP THIS MANUAL FOR FUTURE REFERENCE
IMPORTANT!
2
MAX. HEIGHT OF OVERHEAD DOOR IS 7' (213,3 CM)
• If choosing to install a 7' high overhead door, alternate
framing is required on this shed (Refer to image on left for
dimensions).
• A low headroom overhead door track system may be
required.
• Additional trim material is required around the overhead
door opening.
• A threshold is required to protect the oor at the door
opening (Wood oors only).
• Follow the door manufacturer’s recommendations.
Kit door opening is:
97" (246,3 cm) Wide x 69" (175,2 cm) High
AN OVERHEAD DOOR IS NOT AVAILABLE FROM YARDLINE!
USE INSTRUCTIONS SUPPLIED WITH THE DOOR MANUFACTURER TO FRAME-IN
YOUR FRONT WALL DOOR OPENING.
**PROVIDE THIS PAGE TO THE DOOR MANUFACTURER**
7'
(213,3 cm)
Wall Height
7'
(213,3 cm)
Wall Height
83"
(210,8 cm)
Opening
Additional
trim required
Threshold
Required
2x4 Header
12'
(365,7 cm)
Building Width
12'
(365,7 cm)
Building Width
3
TOOLS
Safety! Always use approved safety glasses during assembly.
OptionalRequired
HELPFUL REMINDER SYMBOLS
Look for these symbols for helpful reminders throughout this manual.
ORIENT LUMBER AND TRIM FOR BEST APPEARANCE
= Assistance Required; two or more people.
= Ensure squareness.
= Important required step or operation.
= Helpful assembly hint.
= Mark part with pencil.
= Beginning of steps for assembly or installation.
= You have nished the assembly or installation.
= Level
❑Gloves
Framing lumber is graded for structural strength and not appearance. Exterior trim is graded for one good side.
Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way
negatively affect the strength or integrity of our product. (See Fig. A, B, C.)
A
❑Safety Glasses
❑Tape Measure
❑Paint Tools
❑Ladder
❑Caulk Gun
❑Hammer
❑Level
FINISH
BEGIN
❑Pencil
❑ Phillips
Screwdriver
❑Drill / Driver
❑3/8" Drill Bit
❑#2 Philips Drive Bit
❑Tool Belt/
Nail Pouch
❑Chalk Line
❑Nail Gun
• gun nails
❑Tin Snips
(for drip edge)
❑Square or
❑Utility Knife
❑Shingle Blades
B C
❑Sawsall
4
Use 100% acrylic latex exterior paint.
For shingles.
PAINT FOR TRIM ........... 1 Gallon
Use 100% acrylic latex exterior paint.
CAULK ........................... 7 Tubes
Use acrylic latex exterior caulk that is paintable.
(2) coats recommended.
Drip edge must be installed to validate warranty.
ADDITIONAL MATERIALS
COMPLETING YOUR SHED
You will need these additional materials:
OPTIONAL MATERIALS
REFER TO THE BACK OF THIS MANUAL AND THE MANUFACTURER’S INSTRUCTIONS FOR
THIS KIT DOES NOT INCLUDE ANY FOUNDATION
OR FLOOR MATERIALS.
For roong felt.
See for a CONCRETE FOUNDATION option.
See for a WOOD FLOOR framing option.
See the FLOOR LEVELING section on for recommended methods and suggested materials to properly
level your framed oor, as this will vary depending on your specic site.
5
A
B
C
4"
(10,2 cm)
3-1/2"
(8,9 cm)
D
D
CONCRETE FOUNDATION
If you choose to install your kit on a concrete slab refer to the diagram below.
Attach the sill plates on the foundaton as shown, and continue on to page 13.
ALWAYS CHECK WITH LOCAL BUILDING CODES FOR CONCRETE SLABS
BEFORE BEGINNING CONCRETE FLOOR.
ABC D
Treated Sill Plate Sill Tape
between
sill plate and
concrete.
Sill plates MUST be treated lumber.
Caulk
DOUBLE
DOORS
WOOD FLOOR MATERIAL LIST (NOT INCLUDED)
6
2" (5,1 cm)
Minimum 5/8" thick panels.Use thicker panels for heavy-duty application
48" x 96" (1,6 x 121,9 x 243,8 cm)
REINFORCED WOOD FLOOR FRAME
NOTE: Depending upon the weight of items you will be storing on your wood oor, you may choose to use
2"x 10"x 12' or 2"x 12"x 12' treated lumber for increased oor strength.
2" x 10" x 12' (5,1 x 25,4 x 365,8 cm) Treated Lumber
2" x 12" x 12' (5,1 x 30,5 x 365,8 cm) Treated Lumber
2 x 8 x 144" (5,1 x 20,3 x 365,8 cm) Treated Lumber
TREATED
3" (7,6 cm)
TREATED
TREATED
REINFORCED FLOOR FRAME MATERIALS LIST
7
and under seams.
FLOOR FRAME NOT INCLUDED
WOOD FRAME FLOOR LEVELING OPTIONS
There are multiple ways to level your oor frame. Our recommended leveling method is shown below.
LEVELING METHODS
MATERIAL REQUIRED
4 x 4 x 12' (10,2 x 10,2 x 305 cm)
Treated Lumber
Always support frame seams.
LEVELING MATERIALS
Gravel
3" (7,6 cm)
Center
this Runner
Measurement to
Measurement to
8" Block
4" Block
Gravel
Gravel
Do not exceed 16".
4x4 Runner
Shingle
Shingle
Maximum between leveling
material locations.
48"
12"
2x4 Treated Lumber
2" Block
Level
12"
8
and under seams.
Measurements to
BEGIN
3
4
1
Use a level and check that the frame is level before applying oor panels.
Check for frame squareness by measuring diagonally across corners. If the measurements are the
same, the frame is square. The diagonal measurement will be approximately .
When the frame is level and square, secure one side of frame to the 4x4 runners using one
fastener at ends of each runner .
At the opposite end of the frame, secure the frame to 4x4 runners using one fastener at ends of
each runner making sure the frame remains square .
Once the oor frame is level and square,
fasten the frame at each point the frame contacts the 4x4 runners .
See page 7 for the preferred oor leveling method.
FINISH
LEVEL AND SQUARE FLOOR FRAME
Before attaching oor decking, it is important to level and square the oor frame.
A level and square oor frame is required to correctly construct your shed.
(Floor frame and decking not included.)
•
•
the frame and where the
one fastener.
9
FLOOR FRAME
PARTS REQUIRED:
1
BEGIN
Cut 25 floor joists down to 141".
Install floor joists 12 on center, as shown.
144"
(365,8 cm)
144"
(365,8 cm)
141"
(358,1 cm)
12"
(30,5 cm)
2 x 8 x 144" (5,1 x 20,3 x 365,8 cm)
TREATED
3" (7,6 cm)
Nail using (3) 3" nails at each location . Use (6) 3" nails at seams .HINT:
Nails
You have nished assembling your oor frame.
FINISH
3Check the oor frame is square by measuring diagonally across the frame corners.
If the measurements are the same your oor frame is square.
The measurement will be approximately 322" .
10
FLOOR PANELS
2" (5,1 cm)
PARTS REQUIRED:
GAUGE BLOCK
GAA
3/4" x 48" x 96"
(1,9 x 121,9 x 243,8 cm)
To draw panels tight
at seams angle nail.
Flush
BEGIN
¸
1
1
BEGIN
¸
1
1
Block
Block
6"
(15,2 cm)
6"
(15,2 cm)
12" (30,5 cm)
48"
(121,9 cm)
Install a panel ush to the outside edges of the oor frame.
Use GAA gauge block to maintain 3/4” on oor joist.
Secure panel using 2" nails 6" apart on edges and 12” apart inside panel.
Flush Flush
Flush
Flush
Flush
12" (30,5 cm)
Install next two panels on frame and ush to the installed panel and outside of frame.
Use GAA gauge block to maintain 3/4” on oor joist.
Secure panel using 2" nails 6" apart on edges and 12" apart inside panel.
11
FLOOR PANELS
2" (5,1 cm)
PARTS REQUIRED:
3/4" x 48" x 96"
(1,9 x 121,9 x 243,8 cm)
GAUGE BLOCK
GAA
Install next two panels and nal panel on frame, ush to the installed panels.
Use GAA gauge block to maintain 3/4” on oor joist.
Secure panels using 2" nails 6" apart on edges and 12" apart inside panel.
4
3
5
Cut one (1) panel in half to get two panels.These panels are cut so that all floor panels
are staggered.
Install panel ush to the outside edge of the oor frame and ush to the installed panel.
Use GAA gauge block to maintain 3/4” on oor joist.
Secure panel using 2” nails 6” apart on edges and 12” apart inside panel.
Block
Block
Block
6" (15,2 cm)
Flush
Flush FlushFlush
12" (30,5 cm)
12
FLOOR PANELS
PARTS REQUIRED:
3/4" x 48" x 96"
(1,9 x 121,9 x 243,8 cm)
2" (5,1 cm)
GAUGE BLOCK
GAA
Install last three oor panels on frame, ush to the outside edge of the oor frame and
ush to installed panels. Use GAA gauge block to maintain 3/4” on oor joists.
Secure panels using 2" nails 6" apart on edges and 12" apart inside panel.
6
6"
(15,2 cm)
Flush
Flush
Flush Flush
12" (30,5 cm)
FINISH
You have nished building your oor.
Block
Block
13
IMPORTANT!
HINT:
SIDE WALL
SIDE WALL
FRONT WALL
BACK WALL
DOOR
STOP!
STOP!
14
PARTS IDENTIFICATION AND SIZES
Letter part identication
is stamped on some parts.
• Check these locations for part stamp.
1 x 4 .................3/4" x 3-1/2" (1,9 x 8,9 cm)
2 x 4 ..............1-1/2" x 3-1/2" (3,8 x 8,9 cm)
2 x 3 ..............1-1/2" x 2-1/2" (3,8 x 6,3 cm)
1 x 3 .................3/4" x 2-1/2" (3,8 x 6,3 cm)
RS RS
RS
ROOF
TRIM WALL
6 x 24" (15,2 x 61 cm)
GABLE 12' x 24' PARTS LIST
2 x 4 x 48" (5,1 x 10,2 x 121,9 cm)
SP
2 x 4 x 38-1/2 (5,1 x 10,2 x 112,1 cm)
2 x 4 x 16-1/8 (5,1 x 10,2 x 41 cm)
CHC
2 x 4 x 44-1/2" (5,1 x 10,2 x 113 cm)
STL
2 x 4 x 84" (5,1 x 10,2 x 213,4 cm)
TO
2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm)
YFA
2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm)
AI
2 x 4 x 92-5/8" (5,1 x 10,2 x 235,3 cm)
UL
2 x 4 x 96" (5,1 x 10,2 x 243,9 cm)
TP
7/16" x 3" x 96" (1,1 x 7,6 x 243,9 cm) OSB
4/4 x 5-1/2" x 57-15/16" (2,5 x 14,0 x 147,2 cm)
ROS
2 x 4 x 81-7/8" (5,1 x 10,2 x 208 cm)
XYA
3/8 x 3" x 83-1/2" (1 x 7,6 x 212,1 cm)
3/8" x 3" x 43-1/8" (1 x 7,6 x109,5 cm)
2 x 4 x 23-7/16" (5,1 x 10,2 x 59,5 cm)
JYA
2 x 4 x 35" (5,1 x 10,2 x 88,9 cm)
QT
2 x 4 x 23" (5,1 x 10,2 x 58,4 cm)
TTA
2 x 4 x 20-1/2" (5,1 x 10,2 x 52,1 cm)
RP
2 x 4 x 22-1/2" (5,1 x 10,2 x 57,1 cm)
AO
2 x 4 x 6-1/2" (5,1 x 10,2 x 16,5 cm)
UY
2 x 4 x 7" (5,1 x 10,2 x 17,8 cm)
AL
19/32" x 3-1/2" x 53" (1,5 x 8,9 x 134,6 cm)
HAB
19/32" x 3-1/2" x 69-15/16" (1,5 x 8,9 x 177,6 cm)
ERR
19/32" x 3-1/2" x 69-15/16" (1,5 x 8,9 x 177,6 cm)
ERL
2 x 4 x 88-1/8" (5,1 x 10,2 x 223,8 cm)
TQA
19/32" x 3-1/2" x 88-1/2" (1,5 x 8,9 x 224,8 cm)
YRL
19/32" x 3-1/2" x 88-1/8" (1,5 x 8,9 x 223,8 cm)
ULL
19/32" x 3-1/2" x 88-1/2" (1,5 x 8,9 x 224,8 cm)
YRR
19/32" x 3-1/2" x 88-1/8" (1,5 x 8,9 x 223,8 cm)
ULR
19/32" x 2-1/2" x 30-1/8" (1,5 x 6,3 x 76,5 cm)
19/32" x 2-1/2" x 39-3/8" (1,5 x 6,3 x 100 cm)
GEA
19/32" x 2-1/2" x 28-1/2" (1,5 x 6,3 x 72,4 cm)
ROR
1 x 3 x 5"
(2,5 x 7,6 x 12,7 cm)
for 3/4" (1,9 cm)
measurement
3/4"
(1,9 cm)
GAA
15
LEFT
LEFT
WALL PANELS & DOORS
DOUBLE DOORS
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
3/8 x 27-1/2 x 48"
(1 x 69,8 x 121,9 cm)
3/8 x 27-1/2 x 48"
(1 x 69,8 x 121,9 cm)
3/8 x 23-7/8 x 84"
(1 x 60,6 x 213,4 cm)
3/8 x 11-1/4 x 48"
(1 x 28,6 x 121,9 cm)
3/8 x 40-1/4 x 48"
(1 x 102,2 x 121,9 cm)
ROOF PANELS
48" x 96"
(121,9 x 243,8 cm)
39-3/4" x 96"
(101,0 x 243,8 cm)
48" x 39-3/4"
(121,9 x 101,0 cm)
UNIVERSAL DOOR
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
3/8 x 48 x 84"
(1 x 121,9 x 213,4 cm)
3/8 x 23-7/8 x 84"
(1 x 60,6 x 213,4 cm)
3/8 x 23-7/8 x 84"
(1 x 60,6 x 213,4 cm)
RIGHT
RIGHT
16
1-1/4" (3,2 cm)
2" (5,1 cm)
3" (7,6 cm)
1" (2,5 cm)
2" (5,1 cm)
1-1/2" (3,8 cm)
1-5/8" (4,1 cm)
FASTENER/HARDWARE & ACCESSORIES
1-1/2" (3,8 cm)
1" (2,5 cm)
DOOR PARTS LIST
NAIL BOXES (Shown Actual Size)
3" (7,6 cm)
2" (5,1 cm)
BOXES
BOXES
3/4" (1,9 cm)
OO
69" Door Stiffener (175,3 cm)
SPA
41-1/2" Door Stiffener (105,4 cm)
NSA
19/32" x 3-1/2" x 41" (1,5 x 8,9 x 104,1 cm)
Vent
19/32" x 3-1/2" x 8-3/8" (1,5 x 8,9 x 16,5 cm)
FTA
1 x 3 x 69-3/4" (2,5 x 7,6 x 177,2 cm)
XSA
19/32" x 3-1/2" x 72-3/8" (1,5 x 8,9 x 183,8 cm)
19/32" x 2-1/2" x 72" (1,5 x 6,3 x 182,9 cm)
19/32" x 2-1/2" x 26-5/8" (3,2 x 6,3 x 67,6 cm)
AH
2" (5,1 cm)
3" (7,6 cm)
3/16 x 46-1/2 x 48”
(0,5 x 118,1 x 121,9 cm)
Pegboard
Door Backer Board
3/8 x 1-5/8 x 69" (1 x 4,1 x 175,3 cm)
Handle
Bolt
Washer
5/16" (0,8 cm)
1" (2,5 cm)
Window
Latch
Hook &
Eyes
17
Your next step will be to build the door and window assemblies shown below.
= LOCATION
INDICATORS
Window Assembly
Door Assembly
You have the opportunity to customize the look of your new Garage by
putting the door and window assemblies in any of the locations shown below.
STOP!
STOP!
18
PARTS REQUIRED:
3" (7,6 cm)
Orient parts on edge on oor as shown.
Nail using (2) 3" nails at each location .
HEADER
Pre-assembled
3
1
BEGIN
HINT:
2 x 4 x 68-1/2" (5,1 x 10,2 x 174 cm)
YFA
2 x 4 x 78-1/2" (5,1 x 10,2 x 199,4 cm)
AI
2 x 4 x 7" (5,1 x 10,2 x 17,8 cm)
AL
You have nished assembling your door frame.
FINISH
Carefully set the door frame aside.
2 x 4 x 35" (5,1 x 10,2 x 88,9 cm)
QT
DOOR FRAME
Assemble header to frame using (2) 3"
nails at each location .
YFA
AI AI
QT
AL
Nails
Nails
Nails
FlushFlush
QT
9-1/2"
(24,1 cm)
25-1/2"
(64,7 cm)
Table of contents
Other Yardline Garden House manuals
Popular Garden House manuals by other brands
Mercia Garden Products
Mercia Garden Products 01OSBA0406DDFW-V1 General instructions
Palmako
Palmako FRF44-3838 installation manual
Weka
Weka 262.2121 ASSEMBLY, USER AND MAINTENANCE INSTRUCTIONS
Billyoh
Billyoh APEX General instructions
Baltic Connexions Oü
Baltic Connexions Oü BCVIL manual
Grosfillex
Grosfillex DECO11 Assembly instructions
XL-BYG
XL-BYG BYGNORDIC Torun 400x300 28 quick start guide
telluria
telluria ELEGANTO 2724 OLL Assembly instructions
Palmako
Palmako FRK44-4757-1 installation manual
Luoman
Luoman Lillevilla 59-2 Assembly and Maintenance
Forest garden
Forest garden WRGH Assembly guide
Lemeks
Lemeks ELC16-1827 instruction manual
OLT
OLT Studio Garden Shed STU128-FJ-Metal Assembly manual
Solid
Solid S8372CR4 manual
Sojag
Sojag 330865570 Assembly manual
Gartenhaus-King
Gartenhaus-King Irina manual
Mercia Garden Products
Mercia Garden Products 03DTSHCR0707FGD2TW-V2 quick start guide
Lemeks
Lemeks Palmako FR28-3020-2 Assembly, installation and maintenance manual