YBIKE EVOLVE User manual

OWNER S MANUAL
NOTE: Any photos of the YBIKE or decals in the owner’s manual are intended to be used as a reference only,
and there may be some differences to the unit you purchased.

IMPORTANT SAFETY NOTICE
SAFETY PRECAUTIONS: The use of a bicycle can be a hazardous activity and precautions should be taken to
avoid dangerous situations. Be sure to read the entire manual before riding. Please pay close attention to the
following notices in particular:
WARNING! Adult assembly required.
x Children riding the bicycle should have constant adult supervision. A responsible adult must inspect the
bicycle prior to use, to ensure that all parts are fully assembled and tightened to prevent accidents.
x Always wear proper protective gear such as a helmet, elbow and kneepads as well as appropriate clothing
such as a long sleeve shirt, gloves, long pants and closed footwear. Do not ride barefoot or in sandals.
x DO NOT use the bicycle on slippery, wet or uneven ground with gravel.
x DO NOT ride the bicycle with one or no hands. Hold the handlebars tightly with two hands.
x Ride the bicycle only on flat and level ground. DO NOT ride the bicycle on slopes. DO NOT go down a long
descending slope or hill. Please be careful when passing these areas.
x Ensure that the handlebar is securely fixed, by turning it left and right, and that the wheels spin smoothly,
before riding the bicycle. Make sure all components are securely fixed and assembled correctly before rid-
ing.
x DO NOT use attachments not included in packaging or attempt to do any modifications yourself as this may
compromise the safety of the ride-on.
x The use of the bicycle is forbidden on roads used by vehicles and on all public roadways in general. Always
follow and obey the local traffic laws for a safe ride.
x Never allow more than one child to ride on the bicycle at any time. Not to be used by children older than 5
years or weighing more than 30 kgs or 66 lbs due to insufficient strength.
x The Evolve is designed for children ages 2—5 years, though the height & size of each individual child varies.
WARNING! CHOKING HAZARD—Small parts. Injury may occur if these precautions are not observed.

YBIKE EVOLVE PARTS LIST & COMPONENTS
Open the box and check that all parts are included:
No. NAME
1 HANDLEBAR (WITH WHEEL)
2 MAIN FRAME
3 HANDLE STEERING CAPS X2
4 WHEELS X2
5 PEDALS X2
6 FLAT HEAD BOLTS X2
7 ROUND HEAD BOLTS X3
8 HANDLEBAR BOLT
9 TRICYCLE: REAR WHEEL BOLT X2
10 BALANCE BIKE: REAR WHEEL BOLT
11 RUNNING BIKE: REAR WHEEL BOLT
12 TWO SETS OF ALLEN KEYS
13 SEAT
0 BRACKET BOLTS X2 (PRE-ASSEMBLED)

Loosen the seat clamp. Insert the
seat post (No. 13) into the frame
2
6
ASSEMBLY INSTRUCTIONS
1. Seat and Handlebar Assembly
(No. 2) until the metal push pin clicks into position into one of the 2 holes provided, to suit
your child. The 2 holes are there to adjust into different seat heights. Close the clamp.
Place the front of the frame (No. 2) with handle steering caps (No.3) on top and under-
neath the frame, as in the picture above, and place this into the space provided on the
handlebar (No. 1). Use the Allen keys (No.12) to secure into position with the flat bolt
head (No.6) from below and handlebar bolt (No. 8) at the top, as in the picture above.
Push pin
3
Seat post
13
2
Seat clamp
3
3
8
1

2. Assembly for Tricycle, Balance Trike or Balance Bike
Your bike is now ready to be assembled into one of three great biking options. Please choose
the corresponding assembly instruction in the pages that follow.
Important Note 1: Each biking option is assembled using numbered holes on the swing arm
bracket to correspond with the numbered holes on the swing arms.
4
Swing Arm
Bracket
Holes for assembly
on Swing Arm
Swing Arms
1 2
3 3
2
1
1 Tricycle 2 Balance Trike 3 Balance Bike
1 2
3

2. Assembly for Tricycle, Balance Trike or Balance Bike
Important Note 2: The bolts 0, 9, 10 and 11 have square necks. When assembled, ensure
these square neck bolts fit tightly into the square holes provided on the swing arm bracket and
swing arms.
These bolts must be inserted from the correct side, as shown in the corresponding assembly
instruction. These square holes will keep the bolt from turning when securing it in place with the
Allen keys.
Important Note 3: The pedals are only intended to be used with the tricycle. Remove the
pedals during assembly for the Balance Trike or Balance Bike biking options.
5
Bolts 0, 9, 10 and 11
have square necks.
The square holes on the
swing arm bracket and on
both swing arms.

Option 1: Tricycle: Wheel Assembly
6
Place the assembled main frame
upside down.
2.1 Align the hole marked “1” on the
swing arm bracket with the hole on the
swing arm. Insert the bracket bolt (No.
0) from the seat side, and secure in
place with a flat head bolt (No. 6) from
underneath the swing bracket.
6
9
7
7
2.2 Place the wheel (No. 4)_on the outside edge of the swing arm, so
that the wheel axel hole aligns perfectly with the hole marked “1” on
the swing arm.
DO NOT insert bolt
(No. 0) from under-
neath the swing
bracket, as it will not
fit from this side.
2.3 Now insert the wheel bolt (No. 9) through the hole marked “1” on the swing arms
and the wheel axel hole, and secure in place with round head bolt (No. 7).
IMPORTANT: To allow the wheels to spin freely, do not over tighten the bolt sets.
See the next page for pedal assembly.

Option 1: Tricycle: Pedal Assembly 1
7
Button
Lever
Wheel Axel Hole
Pedal shaft
Important: The pedals are only
intended to be used with the tricycle.
Remove the pedals during assembly
for the Balance Trike or Balance Bike
biking options.
Turning mechanism

Option 1: Tricycle: Pedal Assembly 2
8
2.4 Press the button in, then while pressing
the button, also slide the lever on the
handlebar (No. 1) turning mechanism
back towards the handlebars, as in
picture A. This will open the wheel axel
hole completely.
2.5 Now, while still holding the lever,
gently slide the pedal shaft (No. 5) into the
hexagonal hole inside the wheel, until it
fits securely, as in picture B.
WARNING! The pedals can fit only one
way. DO NOT force the pedals into the
hole, but slowly rotate the hexagonal
pedal shaft until it smoothly slides into the
hexagonal wheel axel holes.
2.6 Release the lever.
To remove the pedals:
Press the button in, then slide the lever
back to release the pedal shaft.
Button
Lever Wheel Axel Hole
B
A
Pedal
shaft

Option 2: Balance Trike: Wheel Assembly
9
Place the assembled main frame
upside down.
3.1 Align the hole marked “2” on the
swing arm bracket with the hole on the
swing arm. Insert the bracket bolt (No.
0) from the seat side, and secure in
place with a flat head bolt (No. 6) from
underneath the swing bracket.
3.2 Place both wheels (No. 4) on the
inside edge of the swing arms, so that
the wheel axel holes align perfectly
with the holes marked “2” on the swing
arms. Now insert the wheel bolt (No.
10) and secure in place with flat head
bolt (No. 7) using the Allen Keys
(No.12).
WARNING: DO NOT use the pedals with this option to avoid possible injury. Make sure
the bolt set is tightened and not loose.
10
7
6
DO NOT insert bolt 0 from underneath
the swing bracket, as it will not fit from
this side.

10
Place the assembled main frame upside
down.
4.1 Align the hole marked “3” on the swing
arm bracket with the hole on the swing
arm. Insert the bracket bolt (No. 0) from
the seat side, and secure in place with a
flat head bolt (No. 6) from underneath the
swing bracket
4.2 Place one wheel (No. 4) on the inside
edge of the swing arm, so that the wheel
axel holes align perfectly with the holes
marked “3” on the swing arms. Now insert
the wheel bolt (No. 11) and secure in
place with round head bolt (No.7) using
the Allen Keys (No. 12).
6
11
7
WARNING: DO NOT use the pedals with this option to avoid possible injury. Make sure
the bolt set is tightened and not loose.
Option 3: Wheel Assembly: Balance Bike
DO NOT insert bolt (No. 0) from underneath
the swing bracket, as it will not fit from this
side.

CHECK BEFORE RIDING
1. Check that all the bolts are tightened.
2. Check that the handlebar is securely fastened and that it moves smoothly.
3. Check that the wheels can spin smoothly and each part is securely fixed.
4. Finally after checking the above points, you can now start to ride.
WARNING! This product must be assembled by an adult. Read the manufacturer’s instructions before using.
Keep the instructions safe for future reference.
WWW.YBIKEUSA.COM WWW.YBIKE.CO.ZA
11
designed by
www.chromecherry.com