YitaHome TLCFLS-2022 User manual

Pure & Easy
CONTACT US:
If you have any questions about the installation of YITAHOME® products，just contact us
at [phone] from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PMPST
or E-mail us at: [e-mail]
Alternative method to contact us(amazon.com orders only)
1.Log into your amazon account
2.Go to "Your Orders" and find the purchase
3.Click on "Contact Seller"
CEILING FAN
ZSWYHS-V1
ASSEMBLY INSTRUCTIONS
TLCFLS-2022

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
1 2
Safety Information
Thank you for purchasing this quality product. To ensure correct function and safety, please read and save all
instructions before using the product
To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin the fan installation or
before servicing the fan or installing accessories.
Read all instructions and safety information carefully before installing your fan and save these instructions.
Make sure all electrical connections comply with local codes or ordinances and the National Electrical Code. If you are unfamiliar with
electric wiring, please use a qualified and licensed electrician.
Make sure you have a location selected for your fan that allow clear space for the blades to rotate,and at least seven (7) feet of clearance betweem
the floor and the fan blade tips. The fan should be mounted at leaet thirty (30) inches ftom walls or other upright structures.
WARNING: The outlet box and ceiling support joist used must be securely mounted, and capable of supporting at least 100 pounds.To
reduce the risk of fire, electric shock or personal injury, mount to the outlet box marked acceptable for fan supported and use mounting
screws provided with the outlet box. The box must be supported directly by the building structure.
WARNING: To reduce the risk of fire, electric shock or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting
screws provided with the outlet box most outlet boxes commonly used for the support of lighting fixtures are not acceptable for fan
support and may need to be replaced. Consult a qualified electrician if in doubt.
Electrical diagrams are for reference only. Light kits that are not packed with the fan must UL listed and marked suitable for use with the
model fan you are installing. Switches must be UL. general use switches. Refer to the instructions packaged with the light kits and
switches for proper assembly.
After installation is complete, check that all connections are absolutely secure.
After making electrical connections, spliced conductors should be turned upward and pushed carefully up into outlet box. The wires
should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.
WARNING: To reduce the risk of electrical shock and fire, do not use this fan with any solid-state fan speed control device, or rheostat.
Do not separate the reverse switch until the fan has come to a complete stop.
Do not insert anything into the fan blades while they are rotating.
WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as “flanges”) during assembly or after
installation. Do not insert objects in the path of the blades.
To avoid personal injury or damsge to the fan and other items,be cautious when working around or cleaning the fan.
Do not use water or detergent when cleaning the fan or fan blades. A dry dust cloth or lightly dampened cloth will be suitable for most cleaning.
1.
2.
3.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may
may occur. It must be understood that common sense and caution are necessary factors in the nstallation and operation and operation of this fan.
NOTE: This product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities are
different or are impaired, or lack of experience or knowledge, unless such persons are supervised or trained to operate the appliance
by a person responsible for their safety.
NOTE: Children should be supervised to ensure that they do not use appliances as a toy.
4.
SAFETY TIP

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
3 4
SCREWS BAG
ST5x35
Setscrew
Expansion
Screw
Setscrew Stopper
Wire Cap
#8-32
Setscrew
Screw
Washer
Screw Spring
Washer
Balance Pack
Fabric
Washer
Screws
for Blades
6
10
7
Reference Image Qty.
Item
no.
×13
×2
8
×1
9
×13
×2
1
5
2
Reference Image Qty.
Item
no.
×2
×2
3
×4
4
×3
×4
Product Instruction
Mounting Bracket
Downrod
Coupling Cover
Canopy
Hairclip Pin
Motor Assembly Blades
Blade Braket
Light Kit
Clevis Pin
Remote Control
MED
1H
STOP
LOW
LIGHT
HI
ON/OFF
2H
4H
8H

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
5 6
Finish
Finish
1
2
3
washers
Outlet box
spring washer

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
7 8
Finish
Finish
Blue
Blue
White
White
Finish

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
9 10
WARNING: To avoid possible electrical shock, be sure the electricity is turned off in the main fuse box before wiring.
1. Connect the fan to the remote control. The fan’s 4P plug should insert into the the remote control’s
4P plug.
2. Connect the remote control to the house’s power line, then connect the remote control’s white wire
to the house’s white wire. Connect the remote control’s black wire to the house’s black wire, and
connect all the fans’ green ground wires to the house of ground wires. Secure wires.
3. Connect the fan motor to the lamp: connect the fan motor’s 1P white wire to the lamp’s 1P white
wire. Connect the fan motor’s 1P blue wire to the tool’s 1P blue wire.
MAKE THE ELECTRIC CONNECTIONS
Motor
green
FOR MOTOR blackO
to the FAN MOTOR
to the FAN LIGHT
receiver of
remote
control
4P
to AC Power
brown
ACIN N
AC IN L
green
120 Vac
SUPPLY
AC N
AC L
blue
green
FOR MOTOR/LIGHT N white
FOR LIGHT L blue
4P
TO MOTOR blackO
TO MOTOR/LIGHT N white
TO LIGHT L blue
green
!
LIGHT ON/OFF
Fan Speed
H-Highest speed
M-Medium speed
L-Lowest speed
1. Restore electricity to the outlet box by turning the electricity on at the main
fuse box.
2. Remove the battery cover from the remote control transmitter, install the
battery, and replace the cover.
Note: 1). Use a LR03/AAA1.5V battery to replace original one.
2). If not used for a long period of time, remove the battery to prevent
damage to the remote transmitter, and store the remote transmitter
away from excess heat or humidity.
3. Remote control’s functions are as follows, including controlling transmitter,
fan speed and light.
REMOTE CONTROL SETTING AND OPERATION
FAN STOP
Timer
1H-Fan anto turn off after 1 hour
2H-Fan auto turn off after 2 hours
4H-Fan auto turn off after 4 hours
8H-Fan auto turn off after 8 hours
MED
1H
STOP
LOW
LIGHT
HI
ON/OFF
2H
4H
8H

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
11 12
WALL CONTROL SWITCH SETTING AND OPERATION
Table of Contents
1. Fan / Remote is not working
2. Fan is noisy
3. Fan Wobbles
4. Light is not working
Please refer to the instruction sheet for detailed directions and descriptions of
installation steps
and requirements.
1. FAN / REMOTE IS NOT WORKING
Ensure the remote is within the 20 foot range of the receiver
To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker. 2) Remove ba eries from remote.
3) Wait 10 seconds. 4) Replace ba eries and turn power on
Check ba eries to insure they are good and oriented correctly
Check to make sure the frequency switches (DIP Switches) from the remote to the receiver are set to the same frequency
Check the main and branch circuit fuses or breakers
If using a Variable Speed Wall Switch, ensure it is specifically designed for use with a ceiling fan.
Check the line wire connec ns to the fan and the switch wire conn e switch housing per the instru ns
2. THE FAN IS NOISY
Make sure all motor housing screws are tened
Make sure the screws that a an blade to motor ar t
Make sure the wire nut connectors are not ra against each other or the interior wall of the switch housing
Allow 24-hour break in period. Most noises associated with the new fan may disappear during th me
If using a ceiling light kit, make sure the glassware is secur htly
Make sure there is a short distance/gap from the ceiling to the topof the canopy. The canopy should not touch the ceiling!
Make sure your ceiling box is secure and that the rubber isolator pads are used between the moun acket and outlet box
TROUBLESHOOTING GUIDE

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
13 14
3. THE FAN WOBBLES
Verify all blades and blade bracket screws are secure (most fan wobble problems are caused by loose parts). Once fan is properly
installed, run the ceiling fan for 10 minutes to let the fan self-adjust.
If wobble occurs a er running the fan for 10 minutes, verify blade level using the following process:
a)
select a point on the ceiling above the pof one of the blades. Then select the fan blade and measure from the center
of the selected blade to point on the ceiling. Rotate the fan un e next blade is oned and repeat the
measurement using the same point from the ceiling for every blade. Measurements
should be within 1/8 inch.
Customer Service
to order a
Customer Service
complimentary Blade Balancing Kit
4. LIGHT IS NOT WORKING
Check Bulb to make sure it is installed correctly
Remove non-working bulb and replace with a bulb that is known to be a good working bulb
To reset the remote control: 1) Turn off power to fan using the wall switch or circuit breaker. 2) Remove ba eries from
remote. 3) Wait 10 seconds. 4) Replace ba and turn power on
complimentary Blade Balancing Kit
to order a
TROUBLESHOOTING GUIDE
The fan blades have been adjusted in the factory to minimize any wobble
NOTE:CEILING FANS TEND TO MOVE DURING OPERATION DUE TO THE FACT THAT THEY
ARE MOUNTED ON A RUBBER CROMMET. IF THE FAN WAS MOUNTED RIGIDLY TO THE
CEILING, IT WOULD CAUSE EXCESS VIBRATION. MOVEMENT OF A FEW CENTIMENTERS
IS QUITE ACCEPTABLE AND DOES NOT SUGGEST ANY PROBLEM
WOBBLE”
TO REDUCE THE FAN WOBBLE: PLEASE CHECK THAT ALL SCREWS WHICH SECURED THE MOUNTING
BRACKET AND DOWNROD ARE SECURE.
BALANCING A WOBBLING CEILING FAN:
For your convenience, a Balancing Kit is included; please follow this procedure when balancing the fan:
1.Check that all blade and blade arm screws are secure.
2.Most fan wobbling problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the
blades. Measure this distance.Rotate the fan until the next blade is positioned for
measurement. Repeat for each blade. The distance deviation should be equal within
1/8"(0.32cm).
3.Use the enclosed Blade Balancing Kit if the blade
wobble is still noticeable.
4.If the blade wobble is still noticeable, interchanging two
adjacent (side by side) blades can redistribute the weight and possibly result in smoother
operation. WARNING: TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARM WHILE INSTALLING, BALANCING THE BLADES, OR CLEANING THE FAN. DO
NOT INSERT FOREIGN OBJECTS BETWEEN ROTATING FAN BLADES.
NOISE
When it is quiet(especially at night) you may hear occasional small noises. This is normal. Please allow
a 24-hour “breaking-in” period, most noises associated with a new fan disappear during the time.
CARE AND CLEANING
1.Periodic cleaning of your ceiling fan is the only maintenance required. Use a soft brush or lint free cloth to
avoid scratching the paint finish. Please make sure to turn off electricity power before you clean your fan
2.Do not use water when cleaning your ceiling fan. It could damage the motor or the blades
and create the possibility of an electrical shock.
3.Motor has permanently lubricated ball bearing. No need to oil
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY CLEANING OR REPAIRS.
AFTER INSTALLATION