YitaHome TLCFLS-2039 User manual

Pure & Easy
CONTACT US:
If you have any questions about the installation of YITAHOME® products，just contact us
at [phone] from Mon-Fri 8:00 AM-16:30 PM PST / Saturday 8:00 AM-12:00 PMPST
or E-mail us at: [e-mail]
Alternative method to contact us(amazon.com orders only)
1.Log into your amazon account
2.Go to "Your Orders" and find the purchase
3.Click on "Contact Seller"
CEILING FAN
ZSWYHS-V1
ASSEMBLY INSTRUCTIONS
TLCFLS-2039

READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING INSTALLATION.
SAVE THESE INSTRUCTIONS:
•To reduce the risk of personal injury, attach the fan directly to the support structure
of the building according to these instructions, and use only the hardware supplied.
•To avoid possible electrical shock, before installing your fan, disconnect the power
by turning off the circuit breakers to the outlet box and associated wall switch location.
If you cannot lock the circuit breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
•All wiring must be in accordance with national and local electrical codes and
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
•To reduce the risk of personal injury, do not bend the blade attachment system
when installing, balancing, or cleaning the fan. Never insert objects between rotating
fan blades.
•To reduce the risk of fire, electrical shock, or motor damage, do not use a solid-state
speed control with this fan.
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
1 2
Cautions and Warnings
NOTE: The important safety precautions and instructions appearing in the manual
are not meant to cover all possible conditions and situations that may occur. It must
be understood that common sense and caution are necessary factors in the installa-
tion and operation of this fan.
Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor
housing and place on carpet or Styrofoam to avoid damage to finish. Check against
parts inventory that all parts have been included.
BEFORE YOU START
Tools and Materials Required
Contact a licensed electrician if
you are not good at performing
electrical work. It’s the licensed
electrician who installs the fan, if
required by the local code. Do not
use the fan with a dimmer switch.
Turn off power at breaker.
External Hexagonal
Wrench
Wire
Stripper
Phillips
Screw-
Step Ladder
OFF
OFF
Parts Included
Hanger bracket
Motor
A Pack of Screws
remote control
Security Screws
4
5
Reference Image Qty.
Item
no.
×2
×1
1
2
Reference Image Qty.
Item
no.
×1
3
×4
×2
×4
×4
×1
4H2H 8H
1H
自然风 正/反转
1
2
3
4
5
6
风扇停 灯开/关

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
3 4
Remote control connection
After connecting to the controller, install the main body of the fan light and lock
the security screw
Synchronous motor wire
Installing the Hanger Bracket
Please drill 8mm holes on the concrete ceiling, and insert the bolt. Align the
bracket with the hole, then tighten with nuts.
Wood Ceiling
Concrete Ceiling
4

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
5 6
Turn on the power and check the fan's operation.
The appropriate speed settings of warm or cool weather depend on many factors
such as the room size, ceiling height, and fans' number.
OPERATING YOUR FAN
1.Restore electricity to the outlet box by turning the electricity on at
the main fuse box.
2.Remove the battery cover from the remote control transmitter,
then put the battery in and fit the cover on.
Note:
1). Use 2 PCS AAA battery to install.
2). If not used for long periods of time, remove the battery to prevent damage to
the remote transmitter, and store it away from excess heat or humidity.
REMOTE CONTROL SETTING AND OPERATION
1.Note: Receiver must be correctly installed on the fan’s mounting bracket.
2.When the transmitter cannot control the receiver, please check the battery level.
3.When the transmitter cannot control the receiver, please check if similar remote
controls your fan nearby and interferes with each other.
4.Battery’s low power will affect the transmitter’s sensitivity and the signal
reception accordingly. You must replace the battery if its power is low.
5.Please take the battery out of the transmitter to avoid battery leaks when not
used for a long time.
6.Isolation switch must be connected in the line.
7.When a blackout or otherwise circumstances happen, the light will work normally
after the power restores
Before carrying out any cleaning or maintenance work, always make sure that the
appliance is disconnected.
This is normal to hear occasional small noises, when it is quiet (especially at night).
Because slight power fluctuations and frequency signals superimposed in the
electricity for off-peak hot water control may change fan motor noise. Please allow
a 24-hour "breaking-in" period, most noises of a new fan disappear over the time.
1.Periodical cleaning your ceiling fan is the only required maintenance. Use a soft
brush/lint free cloth to avoid scratching the paint. Or use a dust catcher to collect
the dust. Please turn off the electricity power before you clean your fan.
2.Do not use water to clean your ceiling fan. It may damage the motor or the
blades or even evoke an electrical shock.
3.The motor has permanently lubricated ball bearing. No need to oil.
NOTE: MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BEFORE
YOU CLEAN OR REPAIR FANS.
IMPORTANT REMINDERS
MAINTENANCE AND CLEANING

ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
7 8
1. Make sure the fan is getting power.
2. Check the functionality of circuit breaker or fuse panel and wall switch.
3. Confirm fan wires are correctly connected to the house wires.
4. Make sure the blocker of the fan motor is removed.
5. Use your remote to check the power to the breaker and try to work your ceiling fan
manually from afar (Normal switch only for the fan power on/off)
1. Confirm the circuit breaker works normally.
2.Confirm the wire connections are not frayed.
3. Power off the fan and power on it again in 10 minutes.
1. Confirm the coupling cover is NOT hitting the motor.
2. Tighten any loose screws of the light kit , fan blades , motor coupling, down rod ,
brackets and mounting hardware.
3. The ceiling beam must meet the minimum tensile test strength of 30KG for installation.
4. Confirm the wire connections are not rattling against each other.
5. Confirm the fan blades are not cracked. If the fan blades are cracked, replace the
damaged blades with a new set of blades from the same brand to ensure your ceiling
fan is compatible.
Make sure the LED light kit and light bulb are connected well.
Your fan may occasionally jerk forward or backward upon starting up.
This is normal and does not affect the fan operation.
Try these troubleshooting steps before contacting customer service.
TROUBLESHOOTING
SYMPTOM
The fan
doesn’t spin
The fan’s light
does not work
The fan is noisy
The fan or light
automatically
turns on/off
POSSIBLE SOLUTIONS