YOKOGAWA 436101 User manual

User’s
Manual
Yokogawa Electric Corporation
IM 04P01B01-03E
3rd Edition
Model 436101/436102/436103/436104/436106/
437101/437102/437103/437104/437106/
437112/437118/437124
μR10000/μR20000
SD Memory Card (/EM1 Option)

i
IM 04P01B01-03E
Introduction
Thank you for purchasing the μR10000/μR20000 recorder. This manual explains how to use
the SD memory card (/EM1 option) on the recorder. Please use this document together with
the User’s Manual (IM04P01B01-01E or IM04P02B01-01E).
This document mainly uses the μR10000 display for explanations.
Notes
● The contents of this manual are subject to change without prior notice as a result of
continuing improvements to the instrument's performance and functions.
● Every effort has been made in the preparation of this manual to ensure the accuracy of its
contents. However, should you have any questions or find any errors, please contact your
nearest YOKOGAWA dealer.
● Copying or reproducing all or any part of the contents of this manual without
YOKOGAWA’s permission is strictly prohibited.
QR Code
The product has a QR Code pasted for efficient plant maintenance work and asset
information management.
It enables confirming the specifications of purchased products and user’s manuals.
For more details, please refer to the following URL.
https://www.yokogawa.com/qr-code
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
Trademarks
● All YOKOGAWA product and brand names used in this manual are either trademarks or
registered trademarks of Yokogawa Electric Corporation.
● Microsoft and Windows are registered trademarks or trademarks of Microsoft Corporation
in the United States and other countries.
● Adobe and Acrobat are registered trademarks or trademarks of Adobe Systems
Incorporated.
● The SD logo is a registered trademark of the SD association.
● Company and product names that appear in this manual are registered trademarks or
trademarks of their respective holders.
● The company and product names used in this manual are not accompanied by the
registered trademark or trademark symbols (® and ™).
About the Usage of Open Source Software
● The TCP/IP software of this product and the document concerning the TCP/IP software
have been developed/created by YOKOGAWA based on the BSD Networking Software,
Release 1 that has been licensed from University of California.
Revisions
March 2015 1st Edition
July 2017 2nd Edition
February 2020 3rd Edition
3rd Edition: February 2020 (YK)
All Right Reserved, Copyright © 2015, Yokogawa Electric Corporation

ii IM 04P01B01-03E
SD Memory Card Handling Precautions
• SD memory cards are delicate and should be handled with caution.
• Yokogawa provides no warranty for damage to, or loss of data recorded on the SD
memory card, regardless of the cause of such damage or loss. Please always make
backup copies of your data.
• Do not store or use the SD memory card in places with static electricity, near electrically
charged objects, or where electrical noise is present. Doing so can result in electric shock
or damage.
• Do not disassemble or modify the SD memory card. Doing so can result in damage.
• Do not physically shock, bend, or pinch the SD memory card. Doing so can lead to
malfunction.
• During reading/writing of data, do not turn OFF the power, apply vibration or shock, or pull
out the card. Data can become corrupt or permanently lost.
• Only use Yokogawa SD memory cards. Operation cannot be guaranteed with other
brands of card.
• When inserting the SD memory card into the instrument, make sure you orient the card
correctly (face up or down) and that you insert it securely. If not inserted correctly, the
card will not be recognized by the instrument.
• Never touch the SD memory card with wet hands. Doing so can lead to electric shock or
malfunction.
• Never use the SD memory card if it is dusty or dirty. Doing so can lead to electric shock or
malfunction.
• The SD memory card comes formatted.
SD memory cards must be formatted according to the standard established by the SD
Association (https://www.sdcard.org/home). If you want format the SD memory card, use
the instrument’s Format function. If using a PC to perform the formatting, use the SD
memory card formatter software available from the above SD Association.
• You can use SD/SDHC cards (up to 32 GB) on the recorder.
SD Memory Card Specifications and Characteristics
Electrical specifications Operating voltage: 2.7 V to 3.6 V (memory operation)
Operating temperature/humidity –25 to 85°C/20 to 85%RH (no condensation)
Storage temperature/humidity -40 to 85°C/5 to 85%RH (no condensation)
24±0.1 Unit: mm
WP
Writable
Write-protected
SD
32±0.1

iii
IM 04P01B01-03E
Recorder Version and Functions Described in This Manual
This manual covers version 1.5x of the recorder.
Conventions Used in This Manual
Unit
KDenotes 1024. Example: 768K (file size)
kDenotes 1000.
Notes
Improper handling or use can lead to injury to the user or damage to
the instrument. This symbol appears on the instrument to indicate that
the user must refer to the user’s manual for special instructions. The
same symbol appears in the corresponding place in the user's manual
to identify those instructions. In the manual, the symbol is used in
conjunction with the word “WARNING” or “CAUTION.”
Warning Calls attention to actions or conditions that could cause serious or fatal
injury to the user, and precautions that can be taken to prevent such
occurrences.
CAUTION Calls attention to actions or conditions that could cause light injury
to the user or cause damage to the instrument or user’s data, and
precautions that can be taken to prevent such occurrences.
Note Calls attention to information that is important for the proper operation
of the instrument.
Conventions Used in the Procedural Explanations
Bold Characters Denotes keys or character strings that appear on the screen.
Example: Range, Unit
Procedure Carry out the procedure according to the step numbers. All procedures
are written with inexperienced users in mind; depending on the
operation, not all steps need to be taken.
Explanation gives information such as limitations related the procedure.
Explanation

iv IM 04P01B01-03E
Contents
Introduction ................................................................................................................................................ i
SD Memory Card Handling Precautions................................................................................................... ii
Recorder Version and Functions Described in This Manual .....................................................................iii
Conventions Used in This Manual ............................................................................................................iii
Saving and Replaying Data Using an SD Memory Card ..................................................................... 1
Saving and Replaying Measured Data .....................................................................................................1
Saving and Loading Setup Data ............................................................................................................... 1
Setting, Removing, and Formatting SD Memory Cards ....................................................................... 2
Setting an SD Memory Card.....................................................................................................................2
Removing the SD Memory Card............................................................................................................... 3
Formatting SD Memory Cards .................................................................................................................. 4
Configuring to Use SD Memory Cards ................................................................................................ 5
Method of Starting and Stopping Measured Data Saving ........................................................................ 5
Setting Parameters for Measured Data Replay (Dot Model) ....................................................................6
Saving Measured Data to an SD Memory Card .................................................................................. 7
Starting and Stopping Data Saving in Sync with the Starting and Stopping of Recording ....................... 7
Manually Starting and Stopping Data Saving ...........................................................................................8
Starting and Stopping Data Saving with the Remote Control Function ....................................................9
Method of Starting and Stopping Measured Data Replay ...................................................................... 10
Saving and Loading Setup Data ........................................................................................................ 13
Saving Setup Data.................................................................................................................................. 13
Loading Setup Data ................................................................................................................................14
Operation Using Communication Commands ................................................................................... 16

1
IM 04P01B01-03E
Saving and Replaying Data Using an SD Memory Card
Saving and Replaying Measured Data
The recorder can save measured data to an SD memory card. If recording on chart paper is
hindered for some reason such as a paper jam, measured data can be replayed using the
data saved on the SD memory card.
Recorder SD memory card
PC
Replay measured
data to chart paper
Replay measured
data on printer
Save data
Universal Viewer
Printer
Saving Measured Data to an SD Memory Card
The recorder can start and stop saving data to an SD memory card in sync with the starting
and stopping of recording. You can also start and stop saving data using keys whenever
necessary.
Replaying Measured Data from an SD Memory Card
On dot models, measured data can be replayed from an SD memory card on chart paper.
Replay is possible on a recorder that was used for measurement or a recorder of the same
model with equivalent or more functions (see “Recorders That Can Replay Data” on page
10).
To replay data, you set the SD memory card in the recorder, specify the range to replay, and
start. The recorder does not measure while replaying data.
In addition, as with the pen model described below, the measured data saved in an SD
memory card can be handled in Universal Viewer.
On pen models, you can use YOKOGAWA’s Universal Viewer to show the measured data
saved in an SD memory card on the display for verification and printing purposes.
You can download Universal Viewer and its manual from the following URL.
SMARTDAC+ Standard Universal Viewer www.smartdacplus.com/software/en/
SMARTDAC+ Standard Universal Viewer User’s
Manual (IM 04L61B01-01EN)
www.smartdacplus.com/manual/en/
Saving and Loading Setup Data
You can save recorder setup data to an SD memory card. Such data can be edited using
the RXA10 Configuration Software. Moreover, the setup data in the SD memory card can be
loaded and applied to recorders.

2IM 04P01B01-03E
Setting, Removing, and Formatting SD Memory Cards
Setting an SD Memory Card
Procedure
1. Insert an SD memory card in the cart slot.
SD memory card
(the side with
the contacts on top)
Slot
To the slot
The SD memory card becomes available for use. The status display*shows the SD memory
card status.
* When the status display is assigned to the screen, you can press the DISP key several times
to show the display.
Free space
50% or more
When an SD memory card is
not inserted
When the operation for ejecting the
SD memory card has been performed
(ready to be removed safely)
Free space
50% or less Ready to be used
Free space
10% or less
Explanation
SD Memory Card
Only SD memory cards that comply with the following specifications can be used. Operation
of supplied or accessory SD memory cards are already confirmed.
Type SDHC SD
Size Up to 32 GB Up to 2 GB
Format FAT32 FAT16
Note
To format SD memory cards on your PC, use the SD Formatter provided by the SD Association
(https://www.sdcard.org/). (Standard formatting, such as those available on Microsoft Windows, do
not comply with the SD memory card format specifications.)
Front Panel LEDs
Front panel LEDs light or blink in the following manner. The figure is of a μR10000 recorder.
Lights red when the recorder is turned on.
Lights green when an SD memory card is not in use.
Blinks green when an SD memory card is in use (when data is being
saved, replayed, etc.).

3
IM 04P01B01-03E
Removing the SD Memory Card
Procedure
This operation will result in error in the following situations. Moreover, this operation is not
possible in Setting mode or Basic Setting mode.
• Data is being replayed from the SD memory card on chart paper (dot model).
• Setup data is being saved to the SD memory card.
• Setup data is being loaded from the SD memory card.
1. Press the
FUNC
key.
2. Press the key to show SD card, and then press the key.
Func=SD card
3. With Eject showing, press the key.
SD card=Eject
The SD memory card will be ready to be removed safely.
A message “Execution is complete.” is displayed for about 2 seconds and the screen returns to
the data display screen.
If the status display is assigned to the screen, you can check the SD memory card status.
4. Push the SD memory card in and release to eject the card.
The status display will show that no SD memory card is inserted.
Note
If you eject the SD memory card while saving data to it, an error will occur if data is scheduled to be
written to the card within 3 minutes. Eject the SD memory card later, or stop saving data and then
eject the card. Even if you succeed in ejecting the SD memory card while saving data to it, be sure
to insert a new SD memory card into the recorder within 3 minutes.
Setting, Removing, and Formatting SD Memory Cards

4IM 04P01B01-03E
Formatting SD Memory Cards
Be careful because formatting an SD memory card will delete all the files in it.
Procedure
1. Set an SD memory card in the slot.
2. Hold down the
MENU
key for 3 seconds to enter Setting mode.
3. Hold down the and keys simultaneously for 3 seconds to enter Basic
Setting mode.
4. Use the key or SHIFT + key to show Format, and then press the key.
5. Enter the volume label, and then press the key.
Enter the volume label using up to 11 characters. The following characters cannot be
used.
/, °(temperature unit), µ, ²(square), ³(cube), Ω, *
If you press the
ESC/?
key in the middle of the operation, the settings entered up to
then are cancelled, and the display returns to a higher level menu.
Key operation
• Use the key to move the cursor to the position where the character is to be inserted.
• Use the
CHARACTER
key to select the character type.
• Use the key to select a character.
6. To execute, press the key to select Execute and then press the key.
When formatting is complete, the Format complete screen appears.
To not execute formatting, press the
ESC/?
key. The screen returns to the
Basic=Format screen.
Basic=Format
Label=LABEL
Enter the volume label.
Select Execute, and then press to format.
Format=Execute
The SD memory card has been formatted.
ESC/?
SD card
Format complete
Formatting...
Explanation
• The supplied SD memory card comes formatted.
• To prevent the SD memory card performance from degrading, we recommend that you
format it regularly.
Setting, Removing, and Formatting SD Memory Cards

5
IM 04P01B01-03E
Configuring to Use SD Memory Cards
Method of Starting and Stopping Measured Data Saving
Set whether to synchronize saving measured data to the SD memory card with the starting
and stopping of recording.
Procedure
1. Hold down the
MENU
key for 3 seconds to enter Setting mode.
2. Use the key or SHIFT + key to show Aux, and then press the key.
3. Use the key or SHIFT + key to show Data save, and then press the key.
4. Use the key or SHIFT + key to set how to start saving data to the SD
memory card, and then press the key.
See “Explanation” below.
5. Use the key or SHIFT + key to set how to stop saving data to the SD
memory card, and then press the key.
See “Explanation” below.
6. When the Setting complete screen appears, do either of the following:
To correct the setting, press the key.
If you are done, press the ESC/? key.
7. Hold down the
MENU
key for 3 seconds to return to Operation mode.
Set=Aux
Start=FUNC menu
Stop=FUNC menu
Data save
Setting complete
Select the data saving start condition.
Select the data saving stop condition.
The new setting takes effect.
Aux=Data save
ESC/?
Explanation
Method of Starting and Stopping Data Saving
FUNC menu: Use the FUNC key to start and stop saving data to the SD memory card.
Record: Start and stop saving data to the SD memory card in sync with the starting
and stopping of recording on chart paper. Even if this is specified, it is still
possible to start and stop saving data using the FUNC key.
Batch (/BT1 option): Start and stop saving data to the SD memory card in sync with batch
start and stop. If you set the data save start condition to Batch, the stop
condition will also be set to Batch. If you set the data save start condition to
a setting other than Batch, you will not be able to set the stop condition to
Batch. You cannot start or stop saving using the FUNC key.

6IM 04P01B01-03E
Setting Parameters for Measured Data Replay (Dot Model)
To replay the measured data from the SD memory card on chart paper, use the setting
parameters that were used when the data was saved. However, some parameters, such as
the chart speed, can be set so that they can be changed during data replay.
Procedure
1. Hold down the
MENU
key for 3 seconds to enter Setting mode.
2. Use the key or SHIFT + key to show Aux, and then press the key.
3. Use the key or SHIFT + key to show Data replay, and then press the
key.
4. Use the key or SHIFT + key to set whether to allow setting parameters to
be changed during data replay, and then press the key.
See “Explanation” below.
5. When the Setting complete screen appears, do either of the following:
To correct the setting, press the key.
If you are done, press the ESC/? key.
6. Hold down the
MENU
key for 3 seconds to return to Operation mode.
Set=Aux
Mode=Original
Data replay
Setting complete
Set whether to change setting
parameters during data replay.
The new setting takes effect.
Aux=Data replay
ESC/?
Explanation
Measured Data Replay Method
Original: Data is replayed using the setting parameters that were used when the data was
saved. They are the setting parameters that were used when data saving was
started. If settings were changed after starting to save the data, the changes are
not applied during data replay.
Current: Data is replayed using the settings of the recorder used to record the replay.
Before starting data replay, you can change some of the items (see below) if
necessary.
Setting Parameters Used in Data Replay Recording
If you specify Current, setting parameters used for replay recording (“Setting Parameters
for Data Replay” on page 10) is used to replay the data. With this setting, you will be able to
change these setting parameters. If you specify Original, the setting parameters in the data
file (those that were used when the data was saved) will be used to replay the data. The
recording will be equivalent to that at the time data was saved.
Configuring to Use SD Memory Cards

7
IM 04P01B01-03E
Saving Measured Data to an SD Memory Card
Starting and Stopping Data Saving in Sync with the Starting and Stopping of
Recording
If the condition for starting data saving to the SD memory card is set to Record, the recorder
will start and stop saving data to the SD memory card in sync with the starting and stopping
of recording on chart paper.
Explanation
Target Channel and Data and Save Destination Folder
The measured data per scan interval of the channels being recorded on chart paper is saved
in the \DATA0 folder.
File Division and File Names
Files are divided automatically at every about 30 MB. The file name is
YYMMDDhhmmss_xx.RXE.
YYMMDDhhmmss Timestamp of the first data entry.
YY: Year (lower two digits), MM: Month, DD: Day, hh: Hour, mm:
Minute, ss: Second
xx A sequence number in chronological order. The number ranges
from 01 to 99. If the number reaches 99, it returns to 00.
.RXE Extension
File format Binary
Note
• You cannot perform the following operations while data is being saved.
• Change the range, computing equations/constants/TLOG, tags, units, recording zone, partial expanded
recording, recording channel on/off (dot model), batch parameters (when the data saving start/stop
conditions are set to Batch) , data saving start/stop conditions, or the settings in Basic Setting mode.
• Save setting parameters, load setting parameters, or switch to Basic Setting mode
• The estimated amount of data that can be stored in a file (about 30 MB) is as follows.
On the 24-dot model: About 4.4 days when recording 24 channels, about 2.2 days when
recording 24 channels + 24 computation channels. On the 6-dot model: About 5.7 days when
recording 6 channels. On the 4-pen model: About 1.1 days when recording 4 channels.
• Performance may be compromised when there are many data files in the \DATA0 folder. As
a guideline, keep the number of data files in the folder to less than 1000 (manage the files by
deleting or moving them). Further, you cannot create more than 2730 data files in the folder. If
you attempt to do so, an error will occur.
• If the free space on the SD memory card drops low, press FUNC, SD card, and then Eject, and
replace with a new card. Data being converted will be written the next time data is written to the
SD memory card on the new card.
If you want to format an SD memory card on your PC, use the SD memory card formatter
software available from the above SD Association (https://www.sdcard.org/home/).
Or, read “Manually Starting and Stopping Data Saving” on the next page, stop data saving, and
replace the SD memory card.
• SD memory card save duration
Save duration
1GB 32GB
1 pen Approx. 57 days Approx. 1800 days
4 pen Approx. 34 days Approx. 1000 days
6 dots Approx. 170 days Approx. 14 years
12 dots Approx. 240 days Approx. 20 years
18 dots Approx. 170 days Approx. 14 years
24 dots Approx. 130 days Approx. 11 years
(The scan interval on the 6-dot model is 1 s. The scan interval on the 12-dot model and higher
dot models is 2.5 s.)
• Channels that record to the SD memory card are as follows:
• Pen model: Measurement channels whose range assigned to the recording pen is not set to
Skip and computation channels with computation mode set to on (/M1)
• Dot model: Measurement channels with trend recording set to on with their ranges not set to
Skip and computation channels with computation mode set to on (/M1)
• If a power failure occurs while saving data, the recorder recovers in data saving mode. Data
files are separated when a power failure occurs. However, if the data saving start/stop condition
is batch synchronization, data saving stops when the power recovers.

8IM 04P01B01-03E
SD Memory Card Status Display
The SD memory card status can be shown on the screen. The screen switches between
three displays at every about 3 seconds. For the operating procedure, see section 3.6,
“Switching the Display Screen,” and chapter 8, “Setup Operations for Changing the
Displayed Contents,” in the μR10000 Recorder User’s Manual (IM 04P01B01-01E) or the
μR20000 Recorder User’s Manual (IM 04P02B01-01E).
Status Available
Usage 63%
Free 1.41 GB
Total 3.88 GB
Label Y_SD
Remain 194d 4h
Item Description
Status SD non (SD memory card not inserted), Available (SD memory card
available), Removable (SD memory card not used), Saving (data being
saved)
Usage The percentage of space used
Free Free space.
Total SD memory card memory size
Label Volume label Example: Y_SD
Remain Estimated remaining length of time for saving data
Manually Starting and Stopping Data Saving
Procedure
Starting Data Saving
You can perform this procedure when data is not being saved to the SD memory card.
1. Press the
FUNC
key.
2. Press the key to select Data save, and then press the key.
Func=Data save
3. Check that Start is displayed, and then press the key.
Data saving to the SD memory card will start.
Data save=Start
Stopping Data Saving
You can perform this procedure when data is being saved to the SD memory card.
1. Press the
FUNC
key.
2. Press the key to show Data save.
3. Check that Stop is displayed, and then press the key.
Data saving to the SD memory card will stop.
Data save=Stop
Note
If key lock is applied to FUNC key operations, the above operation is not possible. For details on
key lock, see section 3.13, “Activating/Releasing the Key Lock,” and 7.10, “Setting the Key Lock
Function,” in the μR10000 Recorder User’s Manual (IM 04P01B01-01E) or the μR20000 Recorder
User’s Manual (IM 04P02B01-01E).
Saving Measured Data to an SD Memory Card

9
IM 04P01B01-03E
Starting and Stopping Data Saving with the Remote Control Function
You can start and stop data saving using remote input by assigning the “Data save On/Off”
to the remote control input terminal.
For the setup procedure, see section 7.18, “Assigning Functions to the Remote Control Input
Terminals (/R1 Option),” in the μR10000 Recorder User’s Manual (IM 04P01B01-01E) or the
μR20000 Recorder User’s Manual (IM 04P02B01-01E).
Saving Measured Data to an SD Memory Card

10 IM 04P01B01-03E
Replaying Measured Data from an SD Memory Card on
Chart Paper (Dot Model)
Method of Starting and Stopping Measured Data Replay
On dot models, measured data in an SD memory card can be replayed and recorded on
chart paper. This is not possible when recording or computing is in progress or when data is
being saved to the SD memory card.
Recorders That Can Replay Data
Data can be replayed on chart paper using a recorder meeting all the conditions below. The
recorder that saved the data will be referred to as Recorder A.
• Same type of recorder
Data saved with a μR10000 recorder can be replayed on a μR10000 recorder. The same
holds true for the μR20000 recorder.
• Recorder whose number of dots is equal to or more than that of Recorder A
Example: If data is recorded on a 12-dot model, a 12-dot, 18-dot, or 24-dot model is
required.
• Recorder with the Math function if Recorder A has the Math function (/M1 option)
• Recorder whose firmware version is the same or later than that of Recorder A
• Data saved on a pen model cannot be replayed on a dot model.
Setting Parameters for Data Replay
If the recorder is configured to allow setting parameters to be changed during replay, the
following values can be changed. For the operating procedure, see the referenced sections.
Type Item Reference
Section*
Replay method Chart speed 5.4
Recording interval 6.1
Replay item Recording channel on/off 6.6
Trend recording and periodic printout for each channel
Printout 7.7
Channel/tag selection, channel No., alarm, recording start, scale
Channel recording color 7.5, 9.13
Time printout format 7.16
Date printout format 7.19
Conditions for periodic printout 7.8
Reference time and interval (instantaneous mode only)
Batch (/BT1 option) 7.24
Data saved with the batch function set to Use can be replayed by
changing the batch setting to Not.
* Reference section in the μR10000 Recorder User’s Manual (IM 04P01B01-01E) and μR20000
Recorder User’s Manual (IM04P02B01-01E).

11
IM 04P01B01-03E
Procedure
Starting Data Replay
The procedure will be explained using an example of replaying data from 19:00 to 21:00 on
February 3, 2015, from the file “150203101215_01.RXE.”
If you want to change the setting parameters for data replay, change them in advance.
1. Insert an SD memory card in the card slot.
2. Press the
FUNC
key.
3. Press the key to select Data replay, and press the key.
Func=Data replay
4. Check that Start is displayed, and then press the key.
Data replay=Start
Specifying the Data Range to Replay
5. Enter the file name whose data is to be replayed, and then press the key.
In this example, enter “15.”
File=15
Key operation
• Use the key to move the cursor to the position where the character is to be inserted.
• Use the
CHARACTER
key to select the character type.
• Use the key to select a character.
Files are searched using forward matching, and those that are found are displayed. In this
example, ve les have been found. No more than 99 les can be displayed. If more than 99 les
are found, narrow down the search conditions.
150202101215_01
001/005
Number of the selected file/number of files found
*
Name of the selected file
* If more than 99 files are found, “001 100 or more” will appear.
6. Use the key to select the file “150203101215_01,” and press the key.
7. Set the data replay start time, and then press the key.
The default value is the data save start time.
15/02/03 19:00:00
8. Set the data replay stop time, and then press the key.
The default value is the current time.
15/02/03 21:00:00
9. Press the key.
Execute?
Measured data replay starts. The display shows that data replay is in progress.
Replaying now...
Feb.03 19:55:00
Timestamp of data currently replayed
Note
The recorder is in Data Replay mode while data is being replayed.
• Measurement, recording, and alarm detection are not performed.
• The display shows that data replay is in progress and cannot be changed. However, you can
use the FUNC key to switch to the operation menu.
• The recorder cannot be switched to Setting mode or Basic Setting mode.
Replaying Measured Data from an SD Memory Card on Chart Paper (Dot Model)

12 IM 04P01B01-03E
Stopping Data Replay
To stop data replay from the SD memory card on chart paper, follow the procedure below.
1. Press the
FUNC
key.
2. Press the key to display Data replay, and press the key.
3. Check that Stop is displayed, and then press the key.
Data replay will be stopped. “Replaying now” is displayed until data reply is finished.
Data replay=Stop
Explanation
Specifying Data
The following figure shows an example in which the data has been divided into three files by
the auto file division function from data saving start to data saving end.
Range of data to be replayed
Data replay start time
Data save start time
(beginning of data)
Data save stop time
(end of data)
Files that have been automatically divided
File 1 File 2 File 3
Data replay stop time
Time
To replay the section of the data marked as “Range of data to be replayed” in the figure,
specify any of the three files. Specify the data replay start time and the data replay stop time.
If the data replay start time is set to a time earlier than the first data entry, replay recording
starts from the first data entry. Likewise, if the data replay stop time is set to a time later than
the last data entry, replay recording is performed to the last data entry.
Replaying Measured Data
• Trend Recording Interval and Chart Speed for Replaying
If data is replayed using the “Original” setting, data is recorded on chart paper according
to the setup data that was used to save the data, which is in the measurement data file. In
this situation, the settings of the recorder replaying the data will not be affected.
• Replay Recording Operation
The replay recording operation is the same as normal recording operation.
• Replay Recording (Waveform)
Both in normal recording and replay recording, data acquired at the scan interval is
sampled using the recording interval, but the reference time for sampling the data
is different. In replay recording, data with timestamps different from those of normal
recording is replayed.
• Printout Conditions (Same as normal recording)
Channel printout, alarm printout, record start printout, message printout, and periodic
printout may not take place depending on the chart speed. The conditions are the same
as those for normal printout.
Replaying Measured Data from an SD Memory Card on Chart Paper

13
IM 04P01B01-03E
Saving and Loading Setup Data
You can save the recorder’s setup data to an SD memory card and load setup data from an
SD memory card.
Saving Setup Data
To save the recorder’s setup data to an SD memory card, follow the procedure below.
Procedure
1. Hold down the
MENU
key for 3 seconds to enter Setting mode.
2. Use the key or SHIFT + key to show Aux, and then press the key.
3. Use the key or SHIFT + key to show Save param, and then press the
key.
4. Enter a file name, and then press the key.
Set the le name using up to 17 characters. The following characters cannot be used.
/ ° (degree sign) μ 2 (square) 3 (cube) Ω *
The following character strings cannot be used.
CON AUX PRN CLOCK CLOCK$ NUL COM0 to COM9 LPT0 to LPT9
If you press the
ESC/?
key in the middle of the operation, the settings entered up to
then are cancelled, and the display returns to a higher level menu.
When saving settings is complete, an execution complete screen appears.
Key operation
• Use the key to move the cursor to the position where the character is to be inserted.
• Use the
CHARACTER
key to select the character type.
• Use the key to select a character.
5. Hold down the
MENU
key for 3 seconds to return to Operation mode.
Set=Aux
File=CONFIG
Saving param...
Saving parameters
complete
Enter a file name.
Setting parameters are being saved.
Setting is complete.
Aux=Save param
ESC/?
Explanation
Save Destination Folder and File Name Extension
A file with .PUL extension is saved in the \SET0 folder. The saved data can be edited using
the RXA10 Configuration Software.

14 IM 04P01B01-03E
Loading Setup Data
To load setup data from an SD memory card into the recorder, follow the procedure below.
Procedure
Loading Only the Settings of Setting Mode
1. Hold down the
MENU
key for 3 seconds to enter Setting mode.
2. Use the key or SHIFT + key to show Aux, and then press the key.
3. Use the key or SHIFT + key to show Load param, and then press the
key.
4. Enter the name of the setup data file to load, and then press the key.
The result of the forward-matching search is displayed.
Key operation
• Use the key to move the cursor to the position where the character is to be inserted.
• Use the
CHARACTER
key to select the character type.
• Use the key to select a character.
5. Use the key or SHIFT + key to select the file.
6. To execute loading, press the key.
The recorder loads the setup data and returns to Operation mode.
To cancel loading, press the ESC/? key. The screen returns to the Aux=Load param
screen.
Set=Aux
Aux=Load param
File=CON
Enter the file name to search for.
(forward-matching search)
Select the target file.
CONFIG_001
Settings are being loaded.
Applies the loaded settings and switches to Operation mode
Loading param...
Loading the Settings of Basic Setting Mode and Setting Mode
1. Hold down the
MENU
key for 3 seconds to enter Setting mode.
2. Hold down the and keys simultaneously for 3 seconds to enter Basic
Setting mode.
3. Use the key or SHIFT + key to show Load param, and then press the
key.
4. Enter the name of the setup data file to load, and then press the key.
The result of the forward-matching search is displayed.
Key operation
• Use the key to move the cursor to the position where the character is to be inserted.
• Use the
CHARACTER
key to select the character type.
• Use the key to select a character.
5. Use the key or SHIFT + key to select the file, and then press the key.
Saving and Loading Setup Data