Addonics Technologies ExDrive User manual

Addonics Technologies
ExDrive
User Guide
Revision 2.7

2
Table of Contents
I. Introduction
FCC Warning Statement 3
Welcome 4
Hardware Requirement 4
Operating System Requirement 4
Introduction 5
Package Contents 6
II. Installation & Operation
Hardware Installation 7
Driver Installation 10
ExData Pro Installation 12
III. Troubleshooting 13

3
FCC Warning Statement
Note: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy. If not installed and used in accordance with the
instruction, it may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment on and off, the user is
encouraged to try to correct the interference by one or more of the
following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and the receiver.
* Connect the equipment to a power outlet on a different circuit
from that to which the receiver is connected.
* Consult the dealer or a professional radio/TV technician.
Caution: changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to
operate the equipment. To meet FCC requirements, shielded
cables are required to connect the device to a personal computer
and/or other Class B certified device.

4
Welcome
Congratulations on your purchase of the Addonics
Technologies’ ExDrive. We hope you will enjoy our product for
its great features and value. This users guide is designed to help
you install the ExDrive and accompanying ExData software
drivers. It should also explain all the various features built into the
unit.
Your comments are valuable to us for further improvement
to our existing and future products and services. In order for us to
keep you informed of any updates on the ExDrive, or on any new
products or services from Addonics Technologies, please go online
to www.addonics.com to register your warranty at your earliest
convenience.
Hardware Requirement
100% IBM compatible PCMCIA socket, or Universal Serial Bus
(USB). PC/AT or compatible, Pentium 100MHz or higher with
16MB memory or more.
Operating System Requirements
Any of the Following:
MS-DOS 6.22 or later
Microsoft Windows for Workgroups
Microsoft Windows 95/98 (USB version does not support
Windows 95)
Microsoft Windows NT (USB does not support Windows NT)

5
Introduction
Introduction To The Portable Hard Drive
The Addonics Technologies ExDrive is a small, lightweight and
portable 2.5” Hard Disk Drive which comes in capacities starting
at 2GB. The unit is external and uses the PCMCIA socket or USB
port, so there is no need to open up your computer since there are
no cards to install, and no special tools are required for installation.
Just attach the unit to the PCMCIA or USB port of you computer
with the supplied cable, plug in the power cord, install the supplied
software (ExData Pro is optional) and you are done.

6
Package Contents
(1) Addonics Technologies 2.5” ExDrive
(1) PCMCIA (No Driver needed) or UBS Cable (One driver
floppy)
(1) ExData Pro Software (Optional)
(1) AC Power Cable
(1) Owner’s Manual & Registration Card
PCMCIA Package
USB Package

7
Installation
Hardware Installation
1. Make sure the power is off on both your computer and the
ExDrive.
2. *For empty ExDrive case users only:
•PCMCIA and USB installation are the same.
a). Press down the middle of the case and pull it apart.
Note: Try not to use sharp objects to open it; it might damage
the inner IC broad.
a). Remove the case and disassemble the unit into 3 parts.
Note: Take the inner IC broad out

8
b). Connect the 2.5” IDE hard disk to the connector on the IC
broad.
Note: Make sure pins match the connecter
c). Secure the HD on the IC board with 4 screws after
connecting.
Note: Do not screws the screws too tight

9
d). Get ready to put everything back together.
Note: Do not connect power at this time
4. Connect the Portable Hard Drive to your computer’s
PCMCIA or USB port with the supplied PCMCIA or USB
cable.
5. Turn on your computer and Portable Hard Drive’s power.
Get ready to plug in the device. Make sure the green light
goes on after you plug the power cable in and turn on the
switch.

10
Driver Installation
*** Important information for PCMCIA users ***
•You do not need to install driver if you are running
Windows 95 or Windows 98. The Windows will install
its default driver for our PCMCIA card, which is called
the “Standard IDE/ESDI Hard Disk Controller”. After
the Windows installs it, you can find it in “Device
Manager” and under “Hard Disk Controllers”.
*** Important information for USB users ***
•Before you go on. We just want to let you know that
our USB devices do not support Windows 95 and
Windows NT.
For USB users:
1. Make sure your ExDrive is powered on and the USB cable
is attached, then plug the USB cable into your computer.
2. The Windows 98 will find the new hardware when you
plug in the device at the first time, and it will ask you to
insert the driver diskette. Just put the floppy diskette into
the floppy disk drive.