Yoshimura Benelli TNT 135 User manual

RESEARCH&DEVELOPMENT OF AMERICA, INC.
www.yoshimura-rd.com
FENDER ELIMINATOR KIT
070BG191350
Benelli TNT 135
5420 DANIELS STREET STE A, CHINO CA., 91710 · [phone] · [phone] · FAX [phone]
THIS PRODUCT IS NOT DOT APPROVED.
Yoshimura R&D of America, Inc. is not liable or responsible for any resulting event caused by the
installation of this product. Check with local laws and regulations for compliance prior to
installation and use. This product is not intended for use on public highways.
! !

2
** Not shown on diagram.
*** The Yoshimura Universal Turn Signal Bracket Kit is to be used with aftermarket stud-mounted turn signals and is sold separately.
No. Item Description Qty.
1 19135-FEBKT Fender Eliminator Bracket 1
2 070BG-LH-K1 LED Fender Eliminator Light 1
3 070BG-LPF License Plate Frame 1
4 M4X6BHS 4mm x 6mm Button Head Screw 2
5 M6X10BHS 6mm x 10mm Button Head Screw 2
6 M6X12BHS 6mm x 12mm Button Head Screw 2
7 6MMWASHER 6mm Washer 4
8 6MMLN 6mm Nylon Lock Nut 4
** 17029 Yoshimura Sticker Kit 1
** BN-SSS-22-18 Butt Connectors 2
Optional Parts
072BGLTSFK Yoshimura LED Front Turn Signal Kit
072BGLTSR
070BGUNVTBKT
Yoshimura LED Rear Turn Signal Kit w/ Relay
Universal Turn Signal Bracket Kit
Assembly Diagram
1
2
3
4
5
6
7
8

1. Remove passenger seat.
2. Locate and disconnect license plate light
connector.
3. Remove the four bolts securing the stock rear
fender to swingarm. Carefully remove the stock
fender assembly by fishing the license plate
light wire out. Be sure not to damage connector
during removal as they will be re-used.
4. Cut the stock license plate light wires from
the stock fender assembly. Cut wires 8” from
the connector.
Removal
3
Installation
1. Install (No. 2) 070BG-LH-K1, Yoshimura fender
eliminator light onto (No. 1) 19135-FEBKT,
Yoshimura fender eliminator bracket using
(No. 4) M4X6BHS, 4mm button head screws
provided in the kit.
2. Install (No. 3) 070BG-LPF, license plate frame to
(No. 1) 19135-FEBKT, fender eliminator bracket
using (No. 5,6) M6X10BHS & M6X12BHS, 6mm
screws, (No. 7) 6MMWASHER, 6mm washer,
and (No. 8) 6MMLN, 6mm nylon lock nut.
3. Connect the Yoshimura license plate light wires
to the stock license plate light as follows:
Red -to- Red / White
Black -to- Black
a) Strip the stock fender light wire ends
1/4” - 1/2” and insert into BN-SSS-22-18,
butt connectors provided in the kit.
b) Center the spliced wire ends in the
middle and using a heatgun or lighter,
apply heat evenly on the outer edges of
the butt connector to shrink and hold
wires in place.
c) Making sure that the stripped ends are
centered, heat the center of the butt
connector evenly until the solder begins
to liquify.
d) Allow to cool completely and tug both
ends of the wires to verify that connection
is secured.
Scan for link to butt connector instruction video.
4. Remove the four screws in undertail and
remove the rubber cover to route wires through
undertail. Install (No. 1) 19135-FEBKT, fender
eliminator bracket using the stock screws.
5
8
1
2
14
3
6
7

4
5. Route license plate light wires through loops on
(No. 1) 19135-FEBKT, fender eliminator bracket
and through hole in undertail where the rubber
cover was previously removed.
6. Re-connect license plate light connectors.
7. Re-install passenger seat.
8. Check for proper function of license plate light,
turn signals, brake light, and that all brackets
and components are secure prior to riding.