ZALMAN GS1000 SE User manual

www.zalman.com
English version
◈ Please read this manual thoroughly before installation.
◈ Please visit the GS1000 web page at Zalman’s website to view the GS1000
installation video.
E-mail: [email protected]
GS1000 SE

GS1000 SE
2
1. Cautionary Notes 3
2. Specifications
3. Parts List 5
. Installation 8
5. Options 1
▣Contents

3
English
GS1000 SE
1) Please thoroughly read and understand the contents of this User Manual prior
to installation.
2) Check the components list and condition of the product before installation. If
any problem is found, contact the retailer to obtain a replacement.
) Refrain from touching any moving parts to prevent injuries.
4) Please refer to the manual for cable setup/installation. Incorrect installation can
lead to short-circuiting and/or damage(s).
5) Do not block the front and rear air vents.
6) Place on a flat, stable surface with good ventilation, and avoid areas with direct
sunlight, oil, water or excessive moisture.
7) Do not cleanse any surface with chemical cleaners or solvents.(chemicals
including but not limited to: industrial brightener, wax, benzene, alcohol, paint
thinner, mosquito repellent, aromatics, lubricant, detergent etc.)
8) Please wear gloves during the installation process to prevent injuries.
9) The specifications of any product may change without prior notice to improve
performance
Disclaimer) Zalman Tech Co., Ltd. is not responsible for any damages due
to extemal causes, including but not limited to, improper use,
problems with electrical power, accident, neglect, alternation,
repair, improper installation, or improper testing.
1
Cautionary Notes

GS1000 SE
Type Full Tower
Dimensions 640mm x 260mm x 570mm (including feet)
(D x W x H) (25.2 x 10.2 x 22.4 )
Weight 17.4kg ( 8.4lb)
Material(s)
Aluminum / ABS / Steel
Color Options Black / Titanium
Motherboard Compatibility E-ATX / Standard ATX / microATX
PSU Compatibility Standard ATX / ATX12V
PC /AGP card Compatibility Full Size
5.25" Bays x 4 (2 can serve as .5")
3.5" Bays x 6 (Hot Swap Function Optional)
Cooling Components
Top Vent: 120mm Fan Vent x 2
(1 Fan included, 1 optional)
Rear Vent: 120mm Fan Vent x 1
(1 Fan included)
Bottom Vent: 120mm Fan Vent x 2
(Fans optional)
Expansion Slots
(Tool Free Bolts provided) x 7 slots
Front /O port
USB x 2
IEEE1 94(Firewire) x 1
Headphone x 1
Mic x1
2
Specifications

5
English
GS1000 SE
1) GS1000 SE
3
Parts List
Headphones
POWER
Mic IEEE 1 94
USB 2.0
Front View Rear View Top View
Side View

GS1000 SE
6
2) GS1000 SE Blow-Up Diagram
Part No. Part Name Qty
HDD Cover 2
HDD Tray 6
“2 in 1”Bracket 2
5.25"Bay Cover 2
Chassis 1
Top Cover 1
Part No. Part Name Qty
Side Panel 2
PSU Bracket 1
PSU Fan Bracket 1
Rear Foot 1
Front Foot 1
④
⑤
⑦
⑧
⑨
⑩
⑪
③
②
①

7
English
GS1000 SE
3) GS1000 SE Parts
Diagram Part Name Qty Role
Foot (Front/Rear)
CPU 12V
Extension Cable
M/B Stand Off
HDD Screws
PSU Screws
ZM-MC1
(Multi Connector)
Foot Fixing Screws
FDD Cover
CPU Power Extension
Cable
microATX M/B Installation
(silver)
HDD Installation (black)
PSU, Motherboard
Installation (black)
Fan RPM control
(white/low noise/5V,
black/full speed/12V)
Feet Assembly (black)
FDD Installation
Support1
1
20
12
24
1
4
1
Cable Tie Cable Management
10
Hand Screws 5.25"Bay Installation 4

GS1000 SE
8
1) Feet Assembly
2) Side Panel Removal
4
Installation
Front Foot
Rear Foot
Foot Fixing Screw
1 2

9
English
GS1000 SE
3) PSU nstallation
(1) PSU Bracket Removal
(2) PSU Bracket Assembly
B TypeA Type
B TypeA Type
▶A Type : Please position the PSU’s intake facing downwards to optimize PSU
cooling.
▶B Type : Please position the PSU’s intake facing upwards to optimize system
cooling.
※If the system is in a dusty environment, please use the B Type configuration.
Tip
PSU Screw

GS1000 SE
10
4) Motherboard nstallation
micro ATX motherboard
Server motherboard
5) Hot Swap HDD nstallation
(1) 3.5
""HDD Removal
Press the corners of the Hot Swap
Tray towards the center and pull out
as shown in the diagram.
1
3
2
M/B Stand Off
PSU Screw
※When installing a micro ATX or server motherboard, please install the
M/B Stand Offs as shown in the diagram.

11
English
GS1000 SE
(2) HDD Tray HDD installation
1
Push the Hooks located on the underside
of the HDD Tray and push in the direction
as shown above.
Diagram of “open” HDD Tray
2
3 4
5 6
.5"HDD
.5"HDD
.5"HDD
※Please secure the HDDs with
bolts as shown in the diagram
when transporting the case
with HDDs installed.
※Be sure to install the HDD(s)
right-side up or the HDD(s)
will not operate properly.
Please check that the Tray’s metal pins
are aligned with the HDD's fixing holes.
Caution
HDD Screw

GS1000 SE
12
6) 5.25
˝˝Drive nstallation
(1) ODD nstallation
1 2
4 5
3
123
(2) FDD nstallation
(3) HDD nstallation (additional HDD installation in a 5.25 bay)
1 2
3 4
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw
Hand Screw

13
English
GS1000 SE
7) Front /O Cable Connection
Caution
※Mixing the IEEE1 94a and USB2.0 cables can cause severe damage
to the system.
※The Power LED will not function properly if connected with the wrong
polarity (+/-). Please check the motherboard’s manual before
connecting.
For USB 2.0, IEEE1 94a, and audio components, please refer to the
motherboard's manual.

GS1000 SE
1
5
Options
1) Optional Top Panel 120mm Fan nstallation
2) Optional Bottom Panel 120mm Fan nstallation
Bottom Panel Center Fan Installation Bottom Panel Rear Fan Installation
1 2
3 4

15
English
GS1000 SE
3) ZM-MC1(Multi Connector)
(1) Connect the 4-Pin Connector to the PSU as show in the below diagram.
(2) Connect the case fan(s) to the desired voltage / speed connector(s).
(120mm, 92mm fan)
PSU 4-Pin
Connector
5V Connector
900~2 00 RPM
(white)
12V Connector
1800~2800RPM
(black)
(1) Up to 2 Hot Swap PCBs(sold separately) can be installed.
(2) Each Hot Swap PCB can connect up to S-ATA HDDs.
4) Hot Swap PCB nstallation (Optional)

16
MEMO