Zanussi ZBE 603 User manual

ZBE 603
Electric
hob
Instruction
booklet

2
Thank you for selecting our appliance
We wish you lots of enjoyment with your new appliance and we hope that
you will consider our brand again when purchasing household appliances.
Please read this user manual carefully and keep it throughout the product
life cycle as a reference document. The user manual should be passed
on to any future owner of the appliance.

3
Description of the Hob ....................................................................................... 3
Important Safety Information .............................................................................. 4
Before the First Use of the Appliance ................................................................. 6
Operation .......................................................................................................... 6
Maintenance and Cleaning .............................................................................. 10
Something Not Working? ................................................................................. 11
Service and original Spare Parts ...................................................................... 20
Guarantee/Customer Service ........................................................................... 21
European Guarantee ....................................................................................... 22
For the Installer
Electrical Connections ..................................................................................... 14
Wiring Diagram ................................................................................................ 17
Installation ....................................................................................................... 18
Building In ....................................................................................................... 19
For the User
Contents
Description of the Hob
1. Hob top
2. Rapid hotplate - 2000 W - 180 mm dia.
3. Rapid hotplate - 1500 W - 145 mm dia.
4. Control knobs
5. Mains On indicator light
1
2
3
3
2
5
4

4
You MUST read these warnings carefully before installing or using the
hob. If you need assistance, contact our Customer Care Department on
08705 727 727.
Important Safety Information
Installation
•This hob must be installed by qualified
personnel, according to the
manufacturer’s instructions and to the
relevant British Standards.
•Before carrying out any operation,
make sure the appliance is
DISCONNECTED from the power
supply.
•Remove all packaging before using
the hob.
•After unpacking the appliance, make
sure it is not damaged and that the
power cable is in perfect condition.
Otherwise, contact the dealer before
using the appliance.
•TheManufacturerdeclinesanyliability
if the accident-prevention regulations
are not respected.
People safety
•This appliance must only be used by
adults. Make sure children do not
play with the appliance or touch the
controls.
•This appliance is not intended for use
by children or other persons whose
physical, sensory or mental
capabilities or lack of experience and
knowledge prevents them from using
the appliance safely without
supervision or instruction by a
responsible person to ensure that
they can use the appliance safely.
•The exposed parts of this appliance
become hot during cooking and
remain so for some time even after the
appliance is turned off. Keep children
away until the appliance has cooled.
During use
•This product is designed for non-
professional home use, for cooking
food. Do not use it for any other
purpose.
•Modifying or attempting to change
the characteristics of this product is
hazardous.
•Keep the appliance clean. Food
residuals can create the risk of fire.
•In case of faults, never try to repair the
appliance on your own. Repairs
carried out by unqualified persons
can cause damage and accidents.
Firstly, consult this handbook. If you
do not find the necessary information,
contact the nearest Service Centre.
Assistance for this appliance must be
carried out by an authorised Technical
Service Centre. Always demand the
use of original spare parts.
•After using the appliance, make sure
all the controls are in the “CLOSED”
or “OFF” position.
•Do not use steam or steam appliances
to clean the equipment.
•When using a power outlet near this
appliance, make sure the cords of
any electrical appliances being used
do not touch it and are far enough
away from its hot parts.

5
Environmental information
•All the materials used are
environmentally friendly and
recyclable. Please make your
contribution to safeguarding the
environment by using the special
differentiated waste collection
channels.
•Appliances that are no longer used or
unusable are not worthless waste.
Through ecological disposal, various
materials used in manufacturing your
appliance can be recovered.
•Find out about the possibilities of
disposal from your specialised dealer
or local Council.
•When disposing of an old appliance,
make it unusable,by cutting off the
cable.
!The symbol on the product or on
itspackaging indicates that this product
may not be treated as household
waste. Instead it shall be handed over
to the applicable collection point for
the recycling of electrical and
electronic equipment. By ensuring
this product is disposed of correctly,
you will help prevent potential nega-
tive consequences for the environment
and human health, which could
otherwise be caused by inappropriate
waste handling of this product. For
more detailed information about
recycling of this product, please
contact your local city office, your
household waste disposal service or
the shop where you purchased the
product.
These instructions are only valid
for countries whose identification
symbols appear on the handbook
cover and on the appliance.
Keep this instruction book for
future reference and ensure it is
passed on to any new owner.
This appliance is manufactured
according to the following EEC
directives:
2006/952006/95
2006/952006/95
2006/95 EEC - 93/6893/68
93/6893/68
93/68 EEC -
89/33689/336
89/33689/336
89/336 EEC , current edition.
Guide to Use the instructionsGuide to Use the instructions
Guide to Use the instructionsGuide to Use the instructions
Guide to Use the instructions
The following symbols will be found in
the text to guide you throughout the
Instructions:
Safety Instructions
Step by step
instructions for an
operation
Hints and Tips
Environmental
information
""
""
"

6
Electric Hotplates
To switch on a hotplate, turn the
relevant control knob anticlockwise to
the required heat setting.
The control knob is numbered 1 - 6
0- OFF
1- Minimum
6- Maximum
Before the First Use of the Appliance
Before using the appliance
remove all packaging,
including the advertising
labels and any protective
film.
When using the hob for the first
time:
1) place on all the plates a pan filled
with some water;
2) switch the plates on for about 10
minutes at “maximum” position until
water inside the pans boils;
3) then, turn the control knob to
“minumum” and allow the plates to
run for approximately 20 minutes;
4) open a window for ventilation.
During this time, the plates may
smoke a little and an unpleasant
odour may be emitted. This is
absolutely normal and it is
caused by residues of
manufacturing.
Once this operation is carried out,
let the plates to cool down, then clean
them with a soft cloth soaked in warm
water.
Operation
"
Fig. 2
Fig. 1

7
Rapid HotplatesRapid Hotplates
Rapid HotplatesRapid Hotplates
Rapid Hotplates
The rapid hotplates are indicated by
a red dot, and will heat up more quickly
than a normal plate. As the red dots are
painted on the plate, they may
deteriorate during use and even
disappear completely after a period of
time. This will not affect the
performance of the hob.
It is important to note that the
plate may smoke and produce a
slightly unpleasant odour when
used for the first time. This is quite
normal and will disappear after a
short while.
OFF 0
Very Gentle 1To keep food warm
To melt butter and chocolate.
Gentle 2To prepare cream-sauces,
stews and milk puddings
or to fry eggs.
Slow 3Dried vegetables, frozen
food, fruit, boiling water
or milk.
Medium 4Boiled potatoes, fresh
vegetables, pâtés, soups,
broths, pancakes or fish.
High 5Larger stews, meat roll, fish,
omelettes, steaks.
Fast 6Steaks, escalopes and frying.
Suggestions for the correct setting of the
plates are given in the following table.
Electric Hotplates Control
Light
The Hotplates Control Light will come
on each time a cooking zone is switched
on.

8
For the correct use of the hot-
plates
For better efficiency of the electric
hotplates and lower electricity
consumption:
•switch on the hotplates only after
placing the pots on them.
•For cooking on the electric hotplates
it is advisable to use triple-bottom
pots of the same width as the cooking
zone, or slightly larger (Fig. 3).
•Do not use wet pots on the electric
hot-plates, and do not place wet lids
on the switched off hot-plates,
because the moisture and condensate
could damage them.
•If possible, place lids on the pots.
Copper or aluminium pots and pans
are not very suitable for cooking on
the electric hotplates, because they
can leave residues, stains and marks.
Likewise, meat grills in cast iron or
other alloys are not suitable for cooking
on the electric hotplates, because
they cause dangerous accumulation
of heat.
Also, the rough bottom can scratch
the cooktop and the material can
stain it. Possibly choose a meat grill in
stainless steel with triple bottom.
The use of glass containers is also
inadvisable, because they usually
have very uneven bottoms. Never use
plastic containers.
•Do not place unstable or deformed
pots on the hotplates because they
could tip over or spill their contents
and thus cause accidents.
•Pots must not enter the control zone.
•Make sure boiling liquids do not spill
onto the hotplates.
Fig. 3

9
•Do not leave a hotplate switched on
without a pot or with an empty pot.
•Do not place a pot on a cold hotplate
or leave it to cool on a switched-off
hotplate. This could cause damaging
condensation to form.
•For faster cooking and to avoid heat
dispersion, it is advisable to use flat-
bottomed pots, to ensure maximum
contact of the bottoms with the
cooking zone.
•Take care never to lean or reach over
a hot electric plate. Always point pan
handles inward or over the work
surface next to the hob to avoid
accidentally knocking over a pan as
you pass by.
•Do not use the hotplate to warm the
room.
Take care when frying food in
hot oil or fat, as the overheated
splashes could easily ignite.
The stainless steel can become
tarnished if excessively
heated. Therefore prolonged
cooking with potstones,
earthenware pans or cast-iron
plates is inadvisable. Also, do
not use aluminium foil to
protect the top during use.

10
Maintenance and Cleaning
Before any maintenance or
cleaning can be carried out,
you must DISCONNECT the
hob from the electricity supply.
This appliance cannot be
cleaned with steam or with a
steam cleaning machine.
The hob is best cleaned whilst it is
still warm, as spillage can be removed
more easily than if it is left to cool.
The Hob Top
Regularly wipe over the hob top
using a soft cloth well wrung out in warm
water to which a little washing up liquid
has been added. Avoid the use of the
following:
- household detergent and bleaches;
- impregnated pads unsuitable for
non-stick saucepans;
- steel wool pads;
- bath/sink stain removers.
Should the hob top become heavily
soiled, the following products are
recommended:
- For stainless steal hobs use a
proprietary stainless steel cleaner.
- For other hobs use Hob Brite or Bar
Keepers Friend.
The control knobs may be removed
by carefully pulling them upward for
easier cleaning.
Do not leave acid or alkaline
substances (e.g. vinegar, salt,
lemon juice, etc.) on the
cooktop.
The Hotplates
Spills onto the actual plate should be
removed using warm water and a soft
brush, nylon or plastic scourer. To keep
the plates looking as new, hotplate
conditioner can be purchased from most
hardware stores, e.g. "4 Hob" by
HomeCare Products (follow the
manufacturer's instruction for use).
Alternatively, wipe the plates with a
drop of olive oil on a kitchen towel to
avoid rust. It is important to note that the
plate will smoke a little and produce a
slightly unpleasant odour when next
used.
Stainless steel parts: the stainless
steel spill rings may become straw
coloured with use. Use a proprietary
stainless steel cleaner to remove this
straw discolouration. This also applies to
the area around the hotplates on
stainless steel hobs.
Failure to clean and condition
hotplates may lead to rust and
corrosion forming on the surface.
Fig. 4

11
Something Not Working?
If the hob is not working correctly, please carry out the following checks before
contacting your local Service Force Centre.
IMPORTANT: If you call out an engineer to a fault listed below, or to repair a
fault caused by incorrect use or installation, a charge will be made even if the
appliance is under guarantee.
SYMPTOM
#The plate does not heat up.
#The plate is not giving satisfactory
results.
SOLUTION
$Check that the unit is plugged in
and the electrical supply is
switched on.
$Check the mains fuse has not
blown.
$Check the correct control knob
has been turned.
$Check the plate is clean and dry
$Check the cooking pan is the
correct size for the plate.
$Check the cooking pan has a flat
bottom.
$Check the setting is correct for the
type of cooking.
If after all these checks, your hob still
does not operate correctly, contact your
local Service Force Centre.
Please note that it will be necessary
to provide proof of purchase for any in-
guarantee service calls.
In-guarantee customers should
ensure that the above checks have
been made as the engineer will
make a charge if the fault is not a
mechanical or electrical breakdown.

12
Engineers technical data
Heating elements ratings
Rapid front left hotplate
Ø 145 mm 1500 W
Rapid back left hotplate
Ø 180 mm 2000 W
Rapid front right hotplate
Ø 145 mm 1500 W
Rapid back right hotplate
Ø 180 mm 2000 W
Total rating 7000 W
Voltage tension 230 V~ 50 Hz
Cut out dimensions
Width: 560 mm
Depth: 480 mm
Overall dimensions
Width: 594 mm
Depth: 510 mm
Instructions for the Installer

13
Important safety requirements
This hob must be installed in
accordance with the IEE Wiring
Regulations (Current Edition).
Detailed recommendations are
contained in the following British
Standards Codes Of Practice: B.S. 6172/
B.S. 5440, Par. 2 and B.S. 6891 Current
Editions.
Location
This hob has been registered as a
"Class X" appliance according to Fire
Risk Regulations. Minimum distances
detailed below must be observed. The
hob may be located in a kitchen, a
kitchen/diner or bed sitting room, but not
in a bathroom or shower room.
Ensure that there is a minimum distance
of 55 mm between the rear cut out edge
and the wall.
A minimum distance of 100 mm must
be left between the side edges of the
cut out and any adjacent cabinets or
walls.
The minimum distance combustible
material can be fitted above the hob in
line with the edges of the hob is 400 mm.
If it is fitted below 400 mm a space of
50 mm must be allowed from the edges
of the hob.
The minimum distance combustible
material or a cooker hood can be fitted
above the hob is 650 mm.
Fig. 5
Dimensions are given in mm.
600
MIN.

14
Electrical Connections
Any electrical work required to
install this hob should be
carried out by a qualified
electrician or competent
person, in accordance with the
current regulations.
THIS HOB MUST BE
EARTHED.
The manufacturer declines any
liability should these safety measures not
be observed.
This hob is designed to be
connected to a 230 V~ 50 Hz electrical
supply.
Before switching on, make sure the
electricity supply voltage is the same as
that indicated on the hob rating plate.
The rating plate is located on the bottom
of the hob. A copy is attached on the
back cover of this book.
Before carrying out the connection,
make sure:
1) the limiter valve and the electrical
system can take the appliance load (see
the rating plate);
2) the supply system is equipped
with an efficient earth connection in
compliance with the current standards
and regulations;
3) the outlet or omnipolar switch
used for connection are easily
accessible with the appliance installed.
The appliance is not equipped with
a power cable.
A cable of section adequate for the
load must be installed on the
equipment. The type of cable must have
at least T90 temperature
characteristics. It is advisable to use the
following types of cables or others with
similar characteristics: H05 V2V2-F. The
cable has three wires. The earth wire is
yellow/green and must be approx. 2 cm
longer than the phase and neutral wires
(Fig. 6). Fit the cable with a plug suitable
for the load and connect it to a suitable
safety socket.
To connect directly to the mains, a
suitable omnipolar switch complying
with current standards and with a
contact gap of at least 3 mm must be
installed between the appliance and the
electrical system.
The yellow/green earth wire must not
be interrupted by the switch. The brown
phase wire (coming from terminal "L" on
the terminal block) must always be
connected to the power supply phase.
In any case the power cable must be
positioned in such a way that no part of
it reaches a temperature of 50°C higher
than the ambient temperature.
The cable is guided by means of
clamps fixed to the side of the cabinet,
in order to avoid any contact with the
equipment beneath the cooktop.
The Manufacturer declines any
liability if the accident-prevention
regulations are not respected.
Fig. 6
NeutralNeutral
NeutralNeutral
Neutral
Earth (yellow/green)Earth (yellow/green)
Earth (yellow/green)Earth (yellow/green)
Earth (yellow/green)

15
Supply Cable Specifications
Connection Min. size Cable / Fuse
via Cable / flex
flex type
• Appliance 6 mm2PVC/PVC 30 A
Control twin and
Circuit earth
For Uk use only
For Europe use only
Min. size Cable / Fuse
Cable / flex flex type
2.5 mm2H05 V2V2-F (T90) 20 A
Ensure that the hob supply cord
does not come into contact with
surfaces with temperatures
higher than 50 deg. C.
The replacement of electric
cable must be carried out
exclusively by the service for-
ce centre or by personnel
with similar competencies,
in accordance with the
current regulations.

16
Type ofType of
Type ofType of
Type of MonophaseMonophase
MonophaseMonophase
Monophase TriphaseTriphase
TriphaseTriphase
Triphase Triphase YTriphase Y
Triphase YTriphase Y
Triphase Y Biphase YBiphase Y
Biphase YBiphase Y
Biphase Y
connectionconnection
connectionconnection
connection 3f. + neutre3f. + neutre
3f. + neutre3f. + neutre
3f. + neutre 2f. + neutre2f. + neutre
2f. + neutre2f. + neutre
2f. + neutre
ConnectionConnection
ConnectionConnection
Connection
cable withcable with
cable withcable with
cable with
terminalterminal
terminalterminal
terminal
boxbox
boxbox
box
NetworkNetwork
NetworkNetwork
Network
tensiontension
tensiontension
tension 230 V230 V
230 V230 V
230 V ~~
~~
~230 V 3230 V 3
230 V 3230 V 3
230 V 3 ~~
~~
~400 V 3N400 V 3N
400 V 3N400 V 3N
400 V 3N ~~
~~
~400 V 2N400 V 2N
400 V 2N400 V 2N
400 V 2N ~~
~~
~
HeatingHeating
HeatingHeating
Heating
elementelement
elementelement
element 230 V230 V
230 V230 V
230 V 230 V230 V
230 V230 V
230 V 230 V230 V
230 V230 V
230 V 230 V230 V
230 V230 V
230 V
tensiontension
tensiontension
tension
3 X 2,5 mm3 X 2,5 mm
3 X 2,5 mm3 X 2,5 mm
3 X 2,5 mm22
22
24 X 1,5 mm4 X 1,5 mm
4 X 1,5 mm4 X 1,5 mm
4 X 1,5 mm22
22
25 X 1,5 mm5 X 1,5 mm
5 X 1,5 mm5 X 1,5 mm
5 X 1,5 mm22
22
24 X 1,5 mm4 X 1,5 mm
4 X 1,5 mm4 X 1,5 mm
4 X 1,5 mm22
22
2
24 A24 A
24 A24 A
24 A 13 A13 A
13 A13 A
13 A 13 A13 A
13 A13 A
13 A 13 A13 A
13 A13 A
13 A
3
2
121
L1
32
1
L1 L3 L2
32
1
L1 L2
All-electricAll-electric
All-electricAll-electric
All-electric
applianceappliance
applianceappliance
appliance
4
N
4
L3
3
L2
4
N
4
N
CHOICE OF CONNECTION CABLE AND FUSE GUAGE (in Amps)
L1 PE PE PE PE
Electrical connection to the ter-
minal box
The appliance is fitted with a five pole
terminal box whose cables are
predisposed for a 230 V monophase
function (Fig. 7).
In case of a different voltage, carry
out the connection as shown in the table
"CHOICE OF CONNECTION CABLE
AND FUSE GUAGE" below.
The earth wire should be connected
to the terminal marked by the sign .
After having connected the wire to
the terminal secure it with a cable clip.
Fig. 7

17
Wiring Diagram

18
Installation
The hob must be installed
according to the instructions
supplied.
The hob must be installed by
qualified personnelqualified personnel
qualified personnelqualified personnel
qualified personnel to the
relevant British Standards.
Please, ensure that, once the hob
is installed, it is easily accessible
for the engineer in the event of a
breakdown.
When the hob is first installed
Once the hob has been installed,
it is important to remove any
protective materials, which were
put on in the factory.
The manufacturer will not accept
liability, should the above
instructions or any of the other
safety instructions incorporated in
this book be ignored.
These cooktops are designed for
fitting on modular kitchen cabinets
having a depth of between 550 and 600
mm and suitable characteristics.
Fitting the Hob into the
worktop
Carry out the building in of the hob
as follows:
• place the seals supplied with the
hob on the front edge of the cut
out. Then, place them at 11 mm
from the side edges and at 10 mm
from the rear edge, as shown in
the diagram, taking care that the
seals meet without overlapping.
• Place the hob in the cut out,
taking care that it is centred. Fig. 8

19
Fig. 11
Building In
On base cabinet with door
Adequate arrangements must be
ensured in the construction of the
cabinet, to prevent possible contact
with the overheated housing of the top
during operation. The recommended
solution for avoiding this problem is
illustrated in Fig. 10.
The panel under the top must be
easily removed to allow securing and
release of the top in case of technical
service intervention.
On base cabinet with oven
The compartment must have the
dimensions given in Fig. 5 and must be
equipped with supports for allowing
efficient ventilation.
Two possible solutions for preventing
overheating are described in Fig. 11 and
12.
Fig. 10
aa
aa
a) removable cabinet panel
bb
bb
b) possible space useful for
connections
Fig. 9
"• Fix the hob with the relevant fixing
clamps, supplied with the kit (see
diagram). When the screws have
been tightened, the excess seal
can be removed.
The edge of the hob forms a double
seal which prevents the ingress of
liquids. Sealing
gasket

20
Fig. 12
The electrical connection of the top
and that of the oven must be carried out
separately, for electrical reasons and to
facilitate frontal oven removal.
Wall units or extractor hoods must be
at least 650 mm from the cooktop (Fig.
5).
Service and original spare parts
This machine, before leaving the
factory, has been tested and studied by
many experts and specialists, in order to
give you the best results.
Any repair work which needs to be
carried out should be done with the
utmost care and attention.
For this reason we recommend that
for any problem you contact the dealer
who sold it to you, or our nearest
authorized Service Centre, specifying
the nature of the problem, the appliance
model (Mod.), the product number (Prod.
No.) and the serial number (Ser. No.)
marked on the identification plate
supplied in the injectors kit.
Original spareparts, certified by the
product manufacturer and carrying this
symbol are only
available at our
Service Centre and
authorized
spareparts shops.