Zanussi ZGG35214 User manual

EN
User manual 2
DE
Benutzerinformation 14
Hob
Kochfeld
ZGG35214
IT

Contents
Safety information _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2
Safety instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ 3
Product description _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Daily use _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 6
Helpful hints and tips _ _ _ _ _ _ _ _ _ _ _ _ 7
Care and cleaning _ _ _ _ _ _ _ _ _ _ _ _ _ _ 7
Troubleshooting _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 8
Installation _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 9
Technical information _ _ _ _ _ _ _ _ _ _ _ 12
Environment concerns _ _ _ _ _ _ _ _ _ _ _ 13
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an in-
correct installation and use causes injuries and damages. Always
keep the instructions with the appliance for future reference.
Children and vulnerable people safety
Warning! Risk of suffocation, injury or permanent disability.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental ca-
pabilities or lack of experience and knowledge if they are super-
vised by an adult or a person who is responsible for their safety.
• Do not let children play with the appliance. Children under 3
years must not be left unsupervised in the vicinity of the appli-
ance.
• Keep all packaging away from children.
• Keep children and pets away from the appliance when it oper-
ates or when it cools down. Accessible parts are hot.
• If the appliance has a child safety device, we recommend that
you activate it.
• Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
• The appliance and its accessible parts become hot during use.
Do not touch the heating elements.
2
www.zanussi.com

• Do not operate the appliance by means of an external timer or
separate remote-control system.
• Unattended cooking on a hob with fat or oil can be dangerous
and may result in fire.
• Never try to extinguish a fire with water, but switch off the appli-
ance and then cover flame e.g. with a lid or a fire blanket.
• Do not store items on the cooking surfaces.
• Do not use a steam cleaner to clean the appliance.
• Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
• If the supply cord is damaged, it must be replaced by the manu-
facturer, an authorized Service or similarly qualified persons in
order to avoid a hazard.
• Where the appliance is directly connected to the power supply,
an all-pole isolating switch with a contact gap is required. Com-
plete disconnection in compliance with the conditions specified
in overvoltage category III must be guaranteed. The earth cable
is excluded from this.
• When you route the mains cable, make sure that the cable
doesn't come into direct contact (for example using insulating
sleeving) with parts that can reach temperatures of more than
50°C above room temperature.
Safety instructions
Installation
Warning! Only a qualified person must
install this appliance.
• Remove all the packaging.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Keep the minimum distance from the other
appliances and units.
• Always be careful when you move the appli-
ance because it is heavy. Always wear safe-
ty gloves.
• Seal the cut surfaces with a sealant to pre-
vent moisture to cause swelling.
• Protect the bottom of the appliance from
steam and moisture.
• Do not install the appliance adjacent to a
door or under a window. This prevents hot
cookware to fall from the appliance when
the door or the window is opened.
3
www.zanussi.com

• If the appliance is installed above drawers
make sure that the space, between the bot-
tom of the appliance and the upper drawer,
is sufficient for air circulation.
• The bottom of the appliance can get hot.
We recommend to install a non-combustile
separation panel under the appliance to
prevent access to the bottom.
Electrical connection
Warning! Risk of fire and electrical
shock.
• All electrical connections must be made by
a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation make sure
that the appliance is disconnected from the
power supply.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable tangle.
• Make sure the mains cable or plug (if appli-
cable) does not touch the hot appliance or
hot cookware, when you connect the appli-
ance to the near sockets
• Make sure the appliance is installed correct-
ly. Loose and incorrect electricity mains ca-
ble or plug (if applicable) can make the ter-
minal become too hot.
• Make sure that a shock protection is instal-
led.
• Use the strain relief clamp on cable.
• Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact the Service or an electrician
to change a damaged mains cable.
• The electrical installation must have an iso-
lation device which lets you disconnect the
appliance from the mains at all poles. The
isolation device must have a contact open-
ing width of minimum 3 mm.
• Use only correct isolation devices: line pro-
tecting cut-outs, fuses (screw type fuses re-
moved from the holder), earth leakage trips
and contactors.
Gas connection
• All gas connections should be made by a
qualified person.
• Before installation, make sure that the local
distribution conditions (nature of the gas
and gas pressure) and the adjustment of the
appliance are compatible.
• Make sure that there is air circulation around
the appliance.
• The information about the gas supply is on
the rating plate.
• This appliance is not connected to a device,
which evacuates the products of combus-
tion. Make sure to connect the appliance
according to current installation regulations.
Pay attention to requirements regarding ad-
equate ventilation.
Use
Warning! Risk of injury, burns or electric
shock.
• Remove all the packaging, labelling and pro-
tective film (if applicable) before first use.
• Use this appliance in a household environ-
ment
• Do not change the specification of this ap-
pliance.
• Do not let the appliance stay unattended
during operation.
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not put cutlery or saucepan lids on the
cooking zones. They can become hot.
• Set the cooking zone to “off” after use.
• Do not use the appliance as a work or as a
storage surface.
• When you place food into hot oil, it may
splash.
Warning! Risk of fire or explosion.
• Fats and oil when heated can release flam-
mable vapours. Keep flames or heated ob-
jects away from fats and oils when you cook
with them.
4
www.zanussi.com

• The vapours that very hot oil releases can
cause spontaneous combustion.
• Used oil, that can contain food remnants,
can cause fire at a lower temperature than
oil used for the first time.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
Warning! Risk of damage to the
appliance.
• Do not keep hot cookware on the control
panel.
• Do not let cookware to boil dry.
• Be careful not to let objects or cookware fall
on the appliance. The surface can be dam-
aged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the appliance.
• Do not let acid liquids, for example vinegar,
lemon juice or limescale remover, touch the
hob. This can cause matt patches.
• This appliance is for cooking purposes only.
Do not use the appliance for other purpo-
ses, as for example room heating.
• The use of a gas cooking appliance results
in the production of heat and moisture. Pro-
vide good ventilation in the room where the
appliance is installed.
• Make sure that the ventilation openings are
not blocked.
• Prolonged intensive use of the appliance
may call for additional ventilation, for exam-
ple opening of a window, or more effective
ventilation, for example increasing the level
of mechanical ventilation where present.
• Use only stable cookware with the correct
shape and diameter larger than the dimen-
sions of the burners. There is a risk of over-
heating and rupture of the glass plate (if ap-
plicable).
• Make sure the flame does not go out when
you quickly turn the knob from the maximum
to the minimum position.
• Make sure pots are centrally positioned on
the rings and do not stick out over edges of
the cooking surface.
• Use only the accessories supplied with the
appliance.
• Do not install a flame diffuser on the burner.
Care and Cleaning
Warning! Risk of damage to the
appliance.
• Clean regularly the appliance to prevent the
deterioration of the surface material.
• Do not use water spray and steam to clean
the appliance.
• Do not clean the burners in the dishwasher.
• Clean the appliance with a moist soft cloth.
Only use neutral detergents. Do not use
abrasive products, abrasive cleaning pads,
solvents or metal objects.
Disposal
Warning! Risk of injury or suffocation.
• Contact your municipal authority for infor-
mation on how to discard the appliance cor-
rectly.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Flat the external gas pipes.
Service
• Contact the Service to repair the appliance.
We recommend only the use of original
spare parts.
5
www.zanussi.com

Product description
Cooking surface layout
1
2
3
1Rapid burner
2Auxiliary burner
3Control knobs
Control knobs
Symbol Description
no gas supply / off po-
sition
Symbol Description
ignition position / maxi-
mum gas supply
minimum gas supply
Daily use
Warning! Refer to the Safety chapters.
Ignition of the burner
Warning! Be very careful when you use
open fire in kitchen environment.
Manufacturer decline any responsibility in case
of misuse of the flame
Always light the burner before you put
cookware.
Lightning the burner:
1. Push the control knob down and turn it
counterclockwise to the maximum position
( ).
2. Keep the control knob pushed for equal or
less than 10 seconds to let the thermo-
couple warm up. If not, the gas supply will
be interrupted.
3. Adjust the flame after it is regular.
If the burner does not light after some
tries, check if the crown and its cap are in
correct positions.
A
B
C
D
A) Burner cap
B) Burner crown
C) Ignition candle
D) Thermocouple
6
www.zanussi.com

Warning! Do not keep the control knob
pushed for more than 15 seconds.
If the burner does not light after 15 seconds,
release the control knob, turn it into off
position and try to light the burner again after
minimum 1 minute.
Important! In the absence of electricity you
can ignite the burner without electrical device;
in this case approach the burner with a flame,
push the relevant knob down and turn it
counter-clockwise to maximum gas release
position.
If the burner accidentally goes out, turn
the control knob to the off position and try
to light the burner again after minimum 1 mi-
nute.
The spark generator can start automati-
cally when you switch on the mains, after
installation or a power cut. It is normal.
Turning the burner off
To put the flame out, turn the knob to the sym-
bol .
Warning! Always turn the flame down or
switch it off before you remove the pans
from the burner.
Helpful hints and tips
Warning! Refer to the Safety chapters.
Energy savings
• If possible, always put the lids on the pans.
• When the liquid starts to boil, turn down the
flame to barely simmer the liquid.
Warning! Use cookware with diameters
applicable to the size of burners.
Burner Diameters of cookware
Rapid 180 - 240 mm
Auxiliary 80 - 160 mm
Warning! Make sure that the bottoms of
pots do not stand above the control
knobs. If the control knobs are under the
bottoms of pots, the flame heats them up.
Do not put the same pan on two burners.
Warning! Make sure that pot handles is
not above the front edge of the cooktop.
Make sure that pots are centrally put on the
rings in order to get maximum stability and to
get lower gas consumption.
Do not put unstable or damaged pots on the
rings to prevent from spill and injury.
Warning! Do not use a flame diffuser.
Care and cleaning
Warning! Refer to the Safety chapters.
Warning! Deactivate the appliance and
let it cool down before you clean it.
Disconnect the appliance from the electrical
supply before you do cleaning or maintenance
work.
Scratches or dark stains on the surface
have no effect on how the appliance op-
erates.
• You can remove the pan supports to easily
clean the hob.
• To clean the enamelled parts, cap and
crown, wash them with warm soapy water
and dry them carefully before you put them
back.
7
www.zanussi.com

• Wash stainless steel parts with water, and
then dry them with a soft cloth.
•Thepansupportsare not dishwasher
proof. They must be washed by hand.
• The enamel coating occasionally can have
rough edges, so be careful when you wash
the pan supports by hand and dry them. If
necessary, remove stubborn stains with a
paste cleaner.
• Make sure you position the pan supports
correctly after cleaning.
• To make the burners work correctly, make
sure that the arms of the pan supports are in
the centre of the burner.
•Be very careful when you replace the
pan supports to prevent the hob top
from damage.
After cleaning, dry the appliance with a soft
cloth.
Removing the dirt:
1. – Remove immediately: melting plastic,
plastic foil, and food containing sugar.
–Stop the appliance and let it cool
down before you clean: limescale rings,
water rings, fat stains, shiny metallic
discolorations. Use a special cleaner
applicable for surface of hob.
2. Clean the appliance with a damp cloth
and some detergent.
3. At the end rub the appliance dry with
a clean cloth.
The stainless steel can become tarnished if it
is too much heated. Refer to this you must not
cook with potstones, earthenware pans or cast
iron plates.
Cleaning of the spark plug
This feature is obtained through a ceramic ig-
nition candle with a metal electrode. Keep
these components well clean to prevent diffi-
cult lighting and check that the burner crown
holes are not obstructed.
Periodic maintenance
Periodically speak your local Service Force
Centre to check the conditions of the gas sup-
ply pipe and the pressure adjuster, if fitted.
Troubleshooting
Problem Possible cause Remedy
There is no spark when lighting
the gas
• There is no electrical supply • Make sure that the unit is con-
nected and the electrical sup-
ply is switched on.
• Control the fuse. If the fuse is
released more than one time,
refer to a qualified electrician.
• Burner cap and crown are
placed uneven
• Make sure that the burner cap
and crown are in correct posi-
tions.
The flame is blow out immediately
after ignition
• Thermocouple is not heated
sufficient
• After lightning the flame, keep
the knob pushed for equal or
less than 10 seconds.
The gas ring burns unevenly • Burner crown is blocked with
food residues
• Make sure that the injector is
not blocked and the burner
crown is clear of food particles.
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a solu-
tion to the problem yourself, speak your dealer
or the local Service Force Centre.
If you operated the appliance incorrectly,
or the installation was not carried out by a
registered engineer, the visit from the custom-
er service technician or dealer may not take
8
www.zanussi.com

place free of charge, even during the warranty
period.
These data are necessary to help you
quickly and correctly. These data are
available on the supplied rating plate.
• Model description .................
• Product number (PNC) .................
• Serial Number (S.N.) .................
Use the original spare parts only. They are
available at Service Force Centre and ap-
proved spare parts shops.
Labels supplied with the accessories bag
Stick the adhesive labels as indicated below:
MOD.
PROD.NO.
SER.NO
DATA
MOD.
PROD.NO.
SER.NO
DATA
MODELMODEL
MOD.
PROD.NO.
SER.NO.
03 IT
MADE IN ITALY
TYPE
230V-50Hz
IP20
0049
A B C
A) Stick it on Guarantee Card and send this
part (if applicable)
B) Stick it on Guarantee Card and keep this
part (if applicable)
C) Stick it on instruction booklet
Installation
Warning! Refer to the Safety chapters.
Warning! The following instructions
about installation, connection and
maintenance must be carried out by qualified
personnel in compliance with standards and
local regulations in force.
Gas Connection
Choose fixed connections or use a flexible
pipe in stainless steel in compliance with the
regulation in force. If you use flexible metallic
pipes, be careful they do not come in touch
with mobile parts or they are not squeezed. Al-
so be careful when the hob is put together
with an oven.
Important! Make sure that the gas supply
pressure of the appliance obeys the
recommended values. The adjustable
connection is fixed to the comprehensive ramp
by means of a threaded nut G 1/2". Screw the
parts without force, adjust the connection in
the necessary direction and tighten everything.
9
www.zanussi.com

ABC
A) End of shaft with nut
B) Washer
C) Elbow
Liquid gas
Use the rubber pipe holder for liquid gas. Al-
ways engage the gasket. Then continue with
the gas connection.
The flexible pipe is prepared for apply when:
– it can not get hot more than room tempera-
ture, higher than 30°C;
– it is no longer than 1500 mm;
– it shows no throttles;
– it is not subject to traction or torsion;
– it does not get in touch with cutting edges
or corners;
– it can be easily examined in order to make
sure its condition.
The control of preservation of the flexible pipe
consists in checking that:
– it does not show cracks, cuts, marks of
burnings on the two ends and on its full
length;
– the material is not hardened, but shows its
correct elasticity;
– the fastening clamps are not rusted;
– expired term is not due.
If one or more defects are visible, do not repair
the pipe, but replace it.
Important! When installation is complete,
make sure that the seal of each pipe fitting is
correct. Use a soapy solution, not a flame!
Injectors replacement
1. Remove the pan supports.
2. Remove the caps and crowns of the burn-
er.
3. With a socket spanner 7 remove the in-
jectors and replace them with the ones
which are necessary for the type of gas
you use (see table in "Technical Informa-
tion" chapter).
4. Assemble the parts, follow the same pro-
cedure backwards.
5. Replace the rating plate (it is near the gas
supply pipe) with the one for the new type
of gas supply. You can find this plate in
the package supplied with the appliance.
If the supply gas pressure is changeable or
different from the necessary pressure, you
must fit an applicable pressure adjuster on the
gas supply pipe.
Adjustment of minimum level
To adjust the minimum level of the burners:
1. Light the burner.
2. Turn the knob on the minimum position.
3. Remove the control knob.
4. With a thin screwdriver, adjust the by-
pass screw position.
A
A) The by-pass screw
• If you change from natural gas G20 20
mbar (or natural gas G20 13 mbar
1)
) to liq-
uid gas, fully tighten the by-pass screw in.
• If you change from liquid gas to natural gas
G20 20 mbar, undo the by-pass screw ap-
proximately 1/4 of a turn.
• If you change from natural gas G20 20
mbar to natural gas G20 13 mbar
1)
undo
the by-pass screw about 1/4 of a turn.
• If you change from liquid gas to natural gas
G20 13 mbar
1)
, undo the by-pass screw
about 1/2 of a turn.
1) only for Russia
10
www.zanussi.com