zBoost Metro YX540 User manual

zBoost Metro YX540
User Guide
30 day money back guarantee when you buy directly from Wi-Ex. If product is
purchased from a reseller or third party, you must use their return policy.
1 Year Manufacutrer Warranty
Register your zBoost product at www.Wi-Ex.com
v.081310

zBOOST® METRO YX540 USER GUIDE zBOOST® METRO YX540 USER GUIDE
i
About zBoost® from Wi-Ex®
Wi-Ex is the leader in cell phone signal boosters. zBoost® enhances the performance of your cell
phone, PDA and wireless data card.
Compability – Dual Band zBoosts are compable with 800MHz and 1900MHz regardless of
technology- including CDMA and GSM.
Patented technologies protect the carrier network.
1-year manufacturer warranty – register your product at www.Wi-Ex.com.
zBoost® products have more awards, more sales and more locaons than all other signal boosters
…COMBINED.
FCC ID: SO4YX545-PCS-CEL
Warning: Changes or modificaons to this device not expressly approved by Wi-Ex could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against
harmful interference in a residenal installaon. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful
interference to radio communicaons. However, there is no guarantee that interference will not occur in
a parcular installaon. If the equipment does cause harmful interference to radio or television recepon,
which can be determined by turning the equipment offand on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separaon between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is con-
nected
• Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment.
This transmier must not be co-located or operang in conjuncon with any other antenna or transmier.
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiang element
(antenna) shall be installed such that a minimum separaon distance of 20cm (8in) is maintained from all
persons.
FCC Information
Industry Canada Regulations
IC ID: 5544A-YX545PCSCEL
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment
Regulaons. Operaon is subject to the following two condions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operaon.
The term “IC:” before the radio cerficaon number only signifies that Industry Canada technical
specificaons were met.
RF Exposure:
The manufacturer’s rated output power of this equipment is for single carrier operaon. For situaons when
mulple carrier signals are present, the rang would have to be reduced by 3.5 dB, especially where the
output is re-radiated and can cause interference to adjacent band users. This power reducon is to be by
means of input power or gain reducon and not by an aenuator at the output of the device.

zBOOST® METRO YX540 USER GUIDE
ii
zBOOST® METRO YX540 USER GUIDE
iii
Package Contents: zBoost®Metro
Before you begin, make sure all of the following parts came with your zBoost® Metro:
Literature Contents:
①Set Up Overview
Product Contents:
② Base Unit Antenna - 2 dBi
③zBoost® Base Unit
④ Power Supply
⑤ RG-59 (mini) Coaxial Cable - 40 ft
⑥ Signal Antenna
⑦ Short Suction Cup Attachments
⑧ Long Suction Cup Attachments
⑦
⑧
②
Cet appareillage numérique de la classe [B] répond à toutes les exigences de l’interférence canadienne
causant des règlements d’équipement. L’opéraon est sujee aux deux condions suivantes: (1) ce disposif
peut ne pas causer l’interférence nocive, et (2) ce disposif doit accepter n’importe quelle interférence
reçue, y compris l’interférence qui peut causer l’opéraon peu désirée.
Le fabricant nominale de la puissance de sore de ce matériel est simple transporteur. Pour les situaons
lorsque plusieurs signauxporteurs sont présents, l’évaluaon devrait être réduite de 3.5 dB, en parculier
lorsque le signal de sore est ré-émise et peut provoquer des interférences adjacentes à la bande
ulisateurs. Ce pouvoir est de la réducon par le biais de la sore d’alimentaon ou la réducon de gain et
non par un aénuateur à la sore du disposif.
Please note: This unit has been approved for use in Canada under RSS 131, however, consent for the use
of this device to improve cellular or PCS coverage, must be obtained through your cellular or PCS provider,
prior to placing the unit in operaon. Please refer to the Industry Canada document CPC 2-1-05, Secon 6.1
available or viewable at:
hp://www.ic.gc.ca/epic/site/smt-gst.nsf/en/sf08942e.html
Copyright Notice
This manual is copyrighted. All rights reserved. This manual, whole or in part, may not be copied,
photocopied, reproduced, translated or reduced to any electronic medium or machine readable form for
distribuon. This manual whole or in part, may not be modified without prior consent, in wring, from
Wireless Extenders.
Copyright © 2010 by Wireless Extenders, Inc.
Trademarks
Wireless Extenders, Wi-Ex, the Wi-Ex logo, zBoost, the zBoost logo and Extending Cell Zones are registered
trademarks of Wireless Extenders, Inc.
Safety Guidelines
In accordance with FCC requirements of human exposure to radiofrequency fields, the radiang element
(antenna) shall be posioned such that a minimum separaon distance of 8 inches (20cm) is maintained
between the radiang element and the user and/or general populaon.
Limited Liability
In no event shall Wireless Extenders be liable for any direct, indirect, special, punive, incidental,
exemplary or consequenal damages, or any damages, whether in an acon under contract, negligence,
or any other theory, arising out of or in connecon with the set up of, use of, inability to use, or
performance of the informaon, services, products, and materials available from this manual. These
limitaons shall apply notwithstanding any failure of essenal purpose of any limited remedy. Because
some jurisdicons do not allow limitaons on how long an implied warranty last, or the exclusion or
limitaon of liability for consequenal or incidental damages, the above limitaons may not apply to you.
For full warranty guidelines, see page 10.
Safety and Product Warranty Information
Changes or modificaons not expressly approved by Wi-Ex
could void the user’s authority to operate this equipment
and/or void the product warranty.
③
④
⑤
⑥
Note

zBOOST® METRO YX540 USER GUIDE
1
zBOOST® METRO YX540 USER GUIDE
2
Table of Content
About zBoost® from Wi-Ex.......................................................................................................................... i
FCC Informaon..................................................................................................................................i
Industry Canada Regulaons..............................................................................................................i
Safety and Product Warranty Informaon...................................................................................................ii
Copyright Noce................................................................................................................................ii
Trademarks........................................................................................................................................ii
Package Contents: zBoost® Metro..............................................................................................................iii
Table of Content..........................................................................................................................................1
Overview....................................................................................................................................................2
Why indoor signal Can Be Weak........................................................................................................2
Preparing to Set Up Your zBoost® Product...................................................................................................3
Check for Signal Strength..................................................................................................................3
Seng Up Your zBoost® Signal Booster...................................................................................................4- 6
Addional Cable Requirements........................................................................................................6
Confirm That Your zBoost is Working Properly.................................................................................6
zBoost® Base Unit Light Indicators...............................................................................................................7
Improving Your Coverage Area....................................................................................................................7
Technical Specificaons...............................................................................................................................8
Frequently Asked Quesons........................................................................................................................9
zBoost®WarrantyInformaon.............................................................................................................10&11
Overview
Designed for consumers in urban sengs, the zBoost METRO™ cell phone signal booster extends a Cell
Zone™ for mulple users/devices operang on 800 and 1900 MHz frequency bands (except Nextel/iDEN).
You will now be able to use your cell phone INSIDE. Gone are the days when you had to go to the window or
walk outside to use your cell phone. Like a skylight that brings sunlight into your home, zBoost® repeats and
amplifies the outdoor cellular signals into your home or office.
Why Indoor Signals Can Be Weak
There are several obstacles that can contribute to the poor recepon you receive in your condo, apartment
or dorm room:
1. Locaon of the Cell Phone Tower in Relaon to Your Home/Office
While cell phone providers have tried to place cell phone towers to provide the best overall
coverage, local ordinances and terrain features can impose restricons on where these towers can
be placed, liming the signal strength available at your locaon.
2. Obstrucons Caused by Buildings, Terrain and Trees
Cell phone signals can be completely blocked or reflected by buildings, walls, trees, hills and other
terrain features resulng in low signal strength.

zBOOST® METRO YX540 USER GUIDE
3
zBOOST® METRO YX540 USER GUIDE
4
Check for Signal Strength
Before placing a zBoost® in your home, make sure that you can place calls near the window or wherever
you plan to place the Signal Antenna. zBoost® can only bring signal into your home when signal reaches the
Signal Antenna.
Using your cell phone, place a call near this locaon to confirm that enough signal is present to complete the
call.
If you can reliably make and receive calls at that locaon then zBoost® can bring the signal into your home.
If only one signal bar is displayed on your cell phone, indoor coverage will be limited to one small room.
Preparing to Set Up Your zBoost® Product Setting Up Your zBoost® Signal Booster
The METRO boosts signal up to 1500 square feet, making it perfect for apartments, condos and los. No
outside antenna placement is required.
Boost voice and data transmission and improve call clarity in 4 easy steps:
FIRST: Place the Signal Antenna on the interior of a window located in the area of
best signal
Determine the locaon that provides the strongest signal using the signal strength indicator on your cell
phone. Find the locaon on the window that provides the most bars of signal strength. Before proceeding,
make sure that the intended surface is clean and clear of any dust. Then choose the sucon cup aachments
appropriate for your seng (short or long), fasten to the Signal Antenna, and secure to your window.
In order to capture the strongest signal, you may do one or all of the following:
1. Move the antenna around the window – higher is usually beer.
2. Use the long sucon cup aachments provided, in order to create a greater angle in which to
capture the signal. The sucons cups must be vercal on the window (as pictured, with cable at the
boom – not on the side). Avoid draping the coax near the antenna.
3. Keep the Signal Antenna 2 feet from any metal.


zBOOST® METRO YX540 USER GUIDE
5
zBOOST® METRO YX540 USER GUIDE
6
SECOND: Place the zBoost Base Unit where you want to create a Cell Zone™
Connect the Base Unit Antenna and coax to the Base Unit and place it where you need signal. For the widest
possible signal area, it is recommended that you posion the Base Unit near the middle of a room or mount
it on an interior wall. This Base Unit uses an omni-direconal antenna that delivers signal in a circular paern
around the antenna. The zBoost METRO does not require vercal separaon; however, the Signal Antenna
and Base Unit Antenna should have at least 8 feet of horizontal separaon. Increasing separaon of the 2
antennas will opmize zBoost performance.
The Base Unit can be mounted either directly on a wall or placed on a flat surface (e.g. a bookshelf, desk,
end table, etc.). For best results, keep the Base Unit offthe floor and at least 2 feet away from other cords,
metal objects or other wireless devices such as wireless routers or wireless access points. The zBoost METRO
performs best when there are no obstrucons between the zBoost Base Unit and your mobile device.
FOURTH: Connect the zBoost Base Unit to the provided power supply and plug
into a power outlet
Upon inial power up, a solid green LED should
appear indicang normal condions. If a red light
appears, adjustments may be needed. See LED
Indicator secon on page 7 for more informaon.
NOTE: The Base Unit can be plugged into a standard
2 or 3 prong 110 VAC receptacle using the Included
power supply. The power supply consumes less than
10W (less than 0.2A AC).
Additional Cable Requirements
If the distance between the Signal Antenna and the Base Unit requires cable longer than the provided 40
feet, contact Wi-Ex customer service at 1-800-871-1612 or email [email protected].
Conϐirm That Your zBoost® is Working Properly
Perform the following steps to confirm that the unit is now working properly:
1. Unplug the Base Unit power cord.
2. Turn on your cell phone and check the signal meter.
3. Plug the power cord into the Base Unit.
4. Hold your cell phone about 3 feet from the Base Unit and then turn it on. Wait up to 1 minute for
the cell phone to register the signal coming from the Base Unit.
5. If the signal meter shows improvement, your zBoost® unit is working properly.
Cell phone signal bars are approximate and vary from
phone to phone. The number of bars can fluctuate widely,
depending on the locaon of the phone, the posion or
angle of the phone, weather, etc. Most cell phone signal
meters update every 6 to 10 seconds. An increase of only
one bar typically indicates a 4x to 10x signal increase.
Avoid placing the Signal Antenna near metal such as wiring,
things likely in/near a window (e.g. window edge frame,
A/C unit, metal siding, etc..
Power
Supply
Base
Unit
Coax
Cable
Base Unit
Antenna
THIRD: Run the provided coaxial cable between the Base Unit and Signal Antenna
Use the provided RG-59(mini) coaxial cable to connect the Signal Antenna and the Base Unit. Coaxial
connecons can loosen when the cable is moved. Be sure the connecons stay hand-ght.
Note
Note

zBOOST® METRO YX540 USER GUIDE
7
zBOOST® METRO YX540 USER GUIDE
8
When your zBoost® system is in place and fully connected, you should walk throughout the room and see
that you are able to reliably place calls.
Remember, coverage varies based on outdoor signal level, building construcon, and antenna placement.
Coverage in adjoining rooms (next to, above, or below) will be reduced due to walls or ceiling/floors.
Should you desire to improve coverage, you may:
• Move the Base Unit and/or adjust the angle of the Base Unit Antenna.
• Move the antenna around the window – higher is usually beer.
• Move the Base Unit farther from the Signal Antenna or around a wall.
Improving Your Coverage Area
Solid GREEN Normal condion at power up.
Slowly Alternang RED and GREEN zBoost® is working, but at reduced
performance and coverage due to “non-
ideal” setup.
Soluon: Increase the distance between
antenna and amplifier to achieve
maximum performance and coverage.
Fast Flashing RED Indicates insufficient distance between
the antenna and the amplifier. The
amplifier is operang at significantly
reduced coverage.
Soluon: Increase space between base
unit and antenna.
Solid RED System is receiving signals from either
the mobile device or the base staon
transceiver which are too strong for
proper operaon.
Soluons: Move away from receiving
antenna with your cell phone. Move
antenna away from other devices..
Fast Alternang RED and GREEN followed
by no light
The amplifier is disabled.
Soluon: Unplug and start over.
At Initial Power Up Only
zBoost®Base Unit Light Indicators
After Initial Power Up
Solid GREEN Normal condion.
Solid RED System is receiving signals from either
the mobile device or the base staon
transceiver which are too strong for
proper operaon.
Soluon: Please unplug your system. Re-
orient your Signal Antenna and/or Base
Unit to reduce the excessive signal source.
Plug your system back in. If sll solid red,
call customer support 1-800-871-1612..
Product Specications for zBoost METRO – YX540 – Dual Band
PCS band
Frequency Uplink: 1850 to 1910 MHz
Downlink: 1930 to 1990 MHz
System Gain 54dB
PCS bands supported A, D, B, E, F, C
Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT,
UMTS, HSPA, 3G
Cellular band
Frequency Uplink: 824 to 849 MHz
Downlink: 869 to 894 MHz
System Gain 52dB
CEL bands supported A, B, A’, B’
Networks CDMA, GSM, GPRS, EDGE, EVDO, 1xRTT,
UMTS, HSPA, 3G
General
Power Consumpon – Power Supply Current 3W standby; 7W max signal - 2.0A Max
Wall Supply Input ; Voltage 100-240VAC 50-60 Hz ; 5.0VDC
System Cerficaons FCC Parts 15 & 24 (PCS) and Parts 15 & 22
(CEL), Industry Canada
Base Unit Size and Weight 5” x 7” x 1.25” – 9 oz.
Operang Condions Indoor Use Only (40- 105F)
Coverage (open areas) Over 1500 sq 
This product uses patented technology to protect the carrier network
This product is covered by patent US 7,706,744. Other U.S.
and foreign patents pending.

zBOOST® METRO YX540 USER GUIDE
9
zBOOST® METRO YX540 USER GUIDE
10
Frequently Asked Questions
What can I expect my cell phone signal range and strength to be inside my home or office?
The closer you are to the base, the stronger the signal. This will vary with different condions. Some of the
condions that will affect the improved coverage area are signal strength outdoors, the type of building
materials in the home, the placement of the unit and the antenna’s proximity to cellular towers.
You can expect that your indoor coverage will be improved. You will be able to make calls where you couldn’t
before. The degree of improvement will depend upon many factors. The intent of zBoost® products are to
bring outside coverage inside. Just as the signal bars move up and down when outside, the boosted signal
will fluctuate in a similar fashion.
Is a cellular phone signal booster the same as a wireless router; will it help my WiFi signal?
The Wi-Ex unit will not help your WiFi service. This unit is designed to work with wireless PCS and Cellular
phones and devices. The WIFI in your home or office operates on a different frequency.
Is your product available for internaonal use?
Yes, we have products that work on European frequencies. Our zBoost YX520-I– Dual band works on
900MHz and 1800Mhz.
We also sell zBoost ONE YX400-U for UMTS/HSPA devices on the 2100MHz Frequency, a frequency used for
voice and data overseas.
Why isn’t my cell phone indicang more signal with more bars?
You may not always observe more bars that gain on your signal meter because of the signal spreading out
from the antenna. If your phone has a dB meter, 3dB is a significant increase of 2x, 6dB is 4x, and 10dB is
10x. On a four bar phone, one "bar" equals about 10dB.
• The increase in signal you will see depends upon:
• The level of signal at the Signal antenna (outdoor)
• The care of the antenna placement (two feet away from metal, adequate antenna separaon [8 feet
recommended])
• The signal already present inside (related to building losses)
• The distance of your phone/device from the Base Unit (signal spreads or diminishes rapidly with
distance.)
There are usually several cell phones in use at one me in my home, will your product boost all of our
signals simultaneously?
The zBoost® Metro is designed to cover mulple signals simultaneously and will allow mulple users to
operate at the same me.
Limited 1 Year Warranty
Register your product at www.Wi-Ex.com
Wi-Ex® warrants every Wi-Ex® product to be free from defects in material and workmanship under normal
use for the warranty period of one year.
Who Is Covered?
You must have proof of purchase to receive warranty service. A sales receipt or other documentaon
showing the product purchased and the purchase date is considered proof of purchase. This limited
warranty extends only to the original consumer purchaser or any person receiving the product as a gifrom
the original consumer purchaser and to no other purchaser or transferee. This warranty does NOT extend to
commercial users.
What is Covered?
Warranty coverage begins the day you purchase the product. For one year from the original date, the Wi-
Ex® Cell Phone Signal Booster will be repaired or replaced with a new, repaired, refurbished or comparable
product (whichever is deemed necessary by Wi-Ex® ) if it becomes defecve or inoperave. The exchange
will be made without charge to you for parts and labor. You will be responsible for the cost of shipping to the
locaon designated by Wi-Ex®. If Wi-Ex® cannot reasonably repair or replace the unit then Wi-Ex® may, at its
sole discreon, refund the price you paid for the product or the price of the unit.
All products, including replacement products, are covered only for the original warranty period. When the
warranty on the original product expires, the warranty on the replacement product also expires.
What is Excluded?
Your warranty does NOT cover:
• Labor charges for set up of the unit.
• Product replacement because of misuse, accident, lightning damage, unauthorized repair or other
cause not within the control of Wi-Ex®.
• Incidental or consequenal damages resulng from the product. Some states do not allow the
exclusion of incidental or consequenal damages, so the above exclusion may not apply to you.
• Any modificaons or other changes to the product, including but not limited to soware or
hardware modificaons in any way other than as expressly authorized by Wi-Ex® will void this
limited warranty.
• Product that has been modified or adapted to enable it to operate in any country other than the
country for which it was designed, manufactured, approved and/or authorized, or repair of products
damaged by these modificaons.
Warranty Information

zBOOST® METRO YX540 USER GUIDE
11
Make sure you keep…
Please keep your sales receipt or other document showing proof of purchase. Aach it to this User Guide
and keep both nearby. Also, keep the original box and packing material in case you need to return your
product.
Before requesting repair service…
If red light is on, system is receiving signals from either the mobile device or the base staon transceiver
which are too strong for proper operaon. Please unplug your system. Re-orient your Signal Antenna and/
or Base Unit to reduce the excessive signal source. Plug your system back in. If sll solid red, call customer
support 1-800-871-1612.
To get warranty service…
Warranty service will be provided by Wi-Ex®. If you believe you need service for your unit, contact Wi-Ex®
at 1-800-871-1612 or [email protected]. A representave will go through a diagnosc checklist with you.
If it is determined that the product needs to be returned for service or exchanged, you will receive a return
merchandise authorizaon (RMA) number. The representave will give you complete shipping details.
To get out of warranty service…
To obtain out of warranty service, contact Wi-Ex® at 1-800-871-1612 or [email protected] for informaon
on the possibility of any costs for repair or replacement of out-of-warranty products.
Reminder
Record the model and serial number found on the product below:
Model #: __________________________________
Serial #: ___________________________________
Purchase Date: ____________________________