Zen-Me ZMH01A User manual

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd. PAGE 1
Step 1 Step 2
Go to User Manual (see pages 2-12)

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd. PAGE 2
Device Overview 2
Charging and Battery 2
Battery Charging 3
Battery Level 4
Battery Life 5
Maximizing Battery Life 5
Getting Started 6
Pairing the Sensor 7
Turning on the Sensor 7
Placing the Sensor 8
Turning o the Sensor 8
Resetting the Sensor 9
Sensor Flight Mode 9
Turning on Flight Mode 9
Turning o Flight Mode 10
Keeping the Sensor Lens Clean 10
Requirements 11
Disclaimers 11
User Manual
(Contents as in Zen-Me in-App version and www.zenme.io/manual)
CONTENTS

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 3
↑ GO TO CONTENTS
Device Overview
Charging and Battery
The Zen-Me Sensor contains a rechargeable, built-in Lithium-Polymer (LiPo) battery. The battery charge lasts for up to 12 months and is
recharged using the Zen-Me wireless charger.
For product warnings and other important safety information, read the Zen-Me Safety Guide (zenme.io/safetyguide).
WARNING

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 4
↑ GO TO CONTENTS
Battery Charging
Allow 2.5 hours to charge the battery from zero to full capacity at the optimal charging temperature of 21°C (70°F). At other
temperatures, the battery may take longer to charge or fail to reach 100% charge. The sensor will not charge at temperatures outside
the approved range of 0°C to 45°C (32-113°F). Placing the sensor or charger in direct sunlight will heat the devices and aect charging
capability.
If battery temperature is not optimal, the battery may take longer to charge or fail to reach its full charge capacity.
Exposing the sensor or charger to direct sunlight will heat the devices and aect charging performance.
CHARGE TIME (0-100%)
2.5 hours (21°C / 70°F)
CHARGING TEMPERATURE RANGE
0-45°C / 32-113°F
CHARGER OPERATING TEMPERATURE
0-45°C / 32-113°F
OPTIMAL OPERATING TEMPERATURE
21°C / 70°F
Plug the USB-cable into the Zen-Me charger. Connect the other end of
the USB-cable into any standard AC adapter or USB computer port.
The sensor is charging when the sensor light ashes. The sensor will
not operate while charging is taking place.
Place the sensor onto the charger so the sensor lens is facing
upwards. Charging will not take place if the back of the sensor is not in
contact with the charger.
When charging is completed the light turns o.
NOTICE
WARNING

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 5
↑ GO TO CONTENTS
The sensor will not charge when the ambient temperature is outside the approved charging temperature range of 0°C to 45°C (32-113°F).
NOTICE
Do not place any object other than the sensor onto the wireless
charger as this could damage the device.
Do not try to charge the sensor with accessories attached. This will
damage the charger and sensor.
NOTICE
Battery Level
The sensor monitors the battery level and provides status information when connected to the Zen-Me App. Monitor battery status on the
Sensor page of the Zen-Me App. If the status shows a “battery critical” warning, charge the sensor immediately.
The sensor will not send “battery critical” status information if outside wireless range or unable to connect to the Zen-Me App. This could
result in the sensor battery discharging fully without warning. If this happens the sensor will send notication when it recharges and
reconnects to the Zen-Me App.
If the sensor does not respond, the most common cause is that the battery has run out. Check the battery charge by pressing the sensor
Power Button. If the sensor light fades or fails to ash, the battery has discharged completely and must be recharged.
WARNING
To nd out if the battery charge is low, press the sensor Power
Button.
If the sensor light fades or fails to ash, the battery charge is very low
and must be recharged.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 6
↑ GO TO CONTENTS
Battery life varies by use, wireless coverage, conguration, and many other factors; actual results will vary.
WARNING
BATTERY TYPE
Rechargeable, built-in Lithium-Polymer (LiPo) battery
BATTERY LIFE
Up to 6 months per charge
Maximizing Battery Life
Some simple tips to extend the life of your sensor battery:
• Use your sensor within the optimal temperature range. The best temperature is around 21°C.
• Avoid exposing the sensor to direct sunlight if possible.
• Some use cases are less data-intensive and have lower power requirements. Select a use case that optimizes sensor workload and
battery life.
(This is simplied illustration on the eect on intensity vs. battery consumption. The relative consumption is also aected by the
frequency of reading data from the sensor, and radio interference on the usage environment).
Battery life and the rate of power consumption are aected by a number of factors:
NOTICE
Battery Life
STYLE OF USE
Depending on how the sensor is used, it
has more or fewer features enabled. The
more features activated, the greater the
power demand.
INTENSITY OF MEASUREMENT
The frequency settings selected for data
acquisition and transmission inuence the
rate of power usage (see table below).
WIRELESS ENVIRONMENT
High levels of wireless trac or having
numerous devices share the same
space will increase the sensor’s power
consumption.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 7
↑ GO TO CONTENTS
Getting Started
Use the Zen-Me App on your iPhone to control the sensor, monitor your data and experience Zen-Me’s functionality.
The App includes a detailed user-manual to help you get the most from Zen-Me. Follow the instructions below to install the Zen-Me App in
4 easy steps.
The Zen-Me sensor will not work unless it is paired to a mobile device with the Zen-Me App installed and set up. The Zen-Me App is
compatible with devices running iOS 10.1 and later.
NOTICE
Go to the Apple App Store on your iPhone. Use the App Store’s search function to nd and select the Zen-Me
App.
Follow the App Store prompts and download the Zen-Me App. Once installed, open the Zen-Me App and follow the instructions to
get started.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 8
↑ GO TO CONTENTS
Pairing the Sensor
When prompted by the Zen-Me App, turn on the sensor to start pairing. Follow the instructions on the App.
Turn on the sensor by pressing the Power Button. 3 ashes indicate the sensor is turned on.
Repeated ashes at one second intervals indicate the sensor is ready
for pairing.
If the sensor has not paired aer 60 seconds, it turns o
automatically.
Turning on the Sensor
Press the Power Button. 3 ashes indicate power is turned on.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 9
↑ GO TO CONTENTS
Placing the Sensor
Zen-Me sensors give you endless possibilities. They are small, versatile and can be placed almost anywhere to support a limitless choice of
uses and activities.
Discover a range of Use Cases in the Explore section of the Zen-Me App. Grab your favorite Use Case and access helpful advice on the best
way to locate and use your sensor(s). You can even create your own Use Case from scratch if you prefer.
The Explore section of the Zen-Me App tells you all you need to know about getting the most from your sensor(s). Check out the Zen-Me
Forum (https://forum.zenme.io) for extra tips from the Zen-Me community.
Turning o the Sensor
To turn o the sensor, press and hold the Power Button for 5 seconds. 3 ashes indicate the sensor is turned o.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 10
↑ GO TO CONTENTS
Resetting the Sensor
To reset the sensor, press and hold the Power Button for 30 seconds.
Turn on Flight Mode by tapping the Flight Mode button on the Sensor
Page of the Zen-Me App. Ensure the sensor is within range.
One long ash followed by short, repeated ashes indicates the
sensor is reset and ready for pairing.
3 long (2 second) ashes indicate that Flight Mode is turned on.
Sensor Flight Mode
During Flight Mode your sensor continues to gather data, but does not connect or stream data to your mobile device.
When ying, this ensures your sensor does not interfere with aircra communications systems.
Flight Mode can also be used to save battery power if you are not connecting to your sensor for long periods of time.
Turning on Flight Mode reduces power consumption by shutting down the sensor’s Bluetooth radio functionality. This is automatically
reactivated and connection restored when Flight Mode is turned o.
Go to the Sensor Page at your Prole Page on the Zen-Me App and choose the sensor you want to activate in Flight Mode. Tap the Flight
Mode button on the Sensor Page and follow the sensor lights.
Your sensor will monitor and gather data normally while in Flight Mode. However, you will not be able to connect and stream data from
your sensor before turning Flight Mode o.
NOTICE
Turning on Flight Mode

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 11
↑ GO TO CONTENTS
Press power button once to deactivate Flight Mode.
Ensure the sensor lens is always clean and free from blockages.
2 long (2 second) ashes indicate that Flight Mode is turning o.
Once ight Mode is switched o you can connect the app with sensor again.
Turning o Flight Mode
Keeping the Sensor Lens Clean
You can use Flight Mode to save battery on your sensor, if you will not connect your sensor for long time. This will shut down the
Bluetooth Radio but keeps the sensor operating. Once you return you can activate the radio by turning the ight mode o and connect to
your sensor again.
The sensor lens takes measurements from the sensor’s surroundings and continually provides internal instruments with information.
The sensor lens must always be kept free from water, liquids, dust or other particles. Blocked holes in the sensor lens could aect the
performance of your sensor.
NOTICE
NOTICE

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 12
↑ GO TO CONTENTS
Requirements
Disclaimers
Zen-Me requires a compatible iPhone 6 or above with iOS 10.1 or above, and installation of the free Zen-Me App. Use requires registration
of a Zen-Me account and acceptance of Zen-Me Terms of Service (zenme.io/terms).
• All information within this Safety Guide is subject to change without notice or warning.
• Zen-Me Inc. cannot be held liable for any losses resulting from the use of Zen-Me devices or the Zen-Me App.
• Measurements or data featured in this Safety Guide are based on Zen-Me testing standards.
• Reproduction of this Safety Guide in full or part is prohibited unless authorized by Zen-Me Inc.

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd. PAGE 1
Step 1 Step 2
Go to Safety Guide (see pages 2-6)

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 2
↑ GO TO CONTENTS
Responsible Use 2
Care and Maintenance 2
Changes and Modications 3
Batteries 3
Charging 3
Prolonged Heat Exposure 4
Choking Hazard 4
Radio Frequency Radiation Exposure 4
Regulatory Information 5
Disposal and Recycling 5
Disclaimers 5
Support 5
CONTENTS
Important Safety Information for your Zen-Me devices.
Safety Guide
(Contents as in Zen-Me in-App version and www.zenme.io/safetyguide)

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 3
↑ GO TO CONTENTS
Responsible Use
Care and Maintenance
Zen-Me devices include sensitive electronic components (including batteries).
These components can be damaged, lose functionality or cause injury if dropped, burned, crushed, taken apart or subjected to excessively
high temperatures, immersion in liquids or exposed to industrial chemicals or substances in high concentrations, including near
evaporated gases such as helium.
Never use damaged Zen-Me Sensors, Zen-Me Chargers or Zen-Me Pendants. Always operate, transport and store your Zen-Me Sensor,
Zen-Me Charger and Zen-Me Pendant according to the instructions in the Zen-Me product manual at Zen-Me User Manual (zenme.io/
manual).
Zen-Me Sensors and the Zen-Me App are NOT intended for medical use or the diagnosis, cure or prevention of any medical condition. Zen-
Me data has no scientic or medical purpose.
Although the data captured and recorded by Zen-Me can aid decision making, it must NOT be relied on in high-risk situations which could
result in damage to property or the environment or cause personal injury or death.
Zen-Me devices contain no user-serviceable components and do not need any routine servicing or maintenance. Do not try to open or
take apart any Zen-Me Sensor or Zen-Me Charger as this could lead to injury or an allergic reaction to materials contained within internal
components.
Any attempt to open or dismantle a Zen-Me device could result in permanent damage and invalidate your product warranties or
guarantees. Unauthorized repairs may also cancel authority to operate your Zen-Me device under Part 15 of FCC regulations.
If you experience problems with the performance of your Zen-Me device, contact Zen-Me Support (zenme.io/support).
• DO NOT expose your Zen-Me devices to excessively high or low temperatures
• DO NOT use abrasive materials, products or chemicals to clean your Zen-Me devices
• DO NOT use your Zen-Me devices in a sauna or steam room
• DO NOT dispose of your Zen-Me device in a re as this could result in an explosion
• DO NOT charge your Zen-Me Sensor when wet or immersed in water or other liquids
• DO NOT charge your Zen-Me Sensor without following the instructions supplied
• DO NOT use any power source (computer, charging device or adapter) to charge your Zen-Me Sensor unless it is certied by a
recognized testing laboratory
For full information on product care, go to the Zen-Me User Manual (zenme.io/manual).
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
For user manual and other important information about Zen-Me products maintenance, read the Zen-Me User Manual
(zenme.io/manual).

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 4
↑ GO TO CONTENTS
Changes and Modications
Charging
Batteries
Making changes or modications to Zen-Me devices could expose the user and others to injury and may invalidate your authority to
operate the devices in compliance with local regulations.
Other adapters may not meet applicable safety standards. Charging with non-compliant adapters may pose a risk of death or serious
injury.
Using damaged cables or chargers or charging with water or moisture present can cause re, electric shock or other serious injury.
Using damaged cables or chargers or charging with water or moisture present may result in damage to the charger, sensor or other
equipment.
When using the Zen-Me Charger DO NOT place metal objects on the charger (such as keys, coins, batteries or metal jewellery) as these
objects may heat-up or interfere with charging.
Charging the Zen-Me Sensor in a potentially explosive atmosphere (e.g. environments with high levels of ammable substances or vapour)
may cause injury or death.
Batteries are a potential health hazard and may cause serious injury or death.
Do not attempt to open the sensor case to replace the battery yourself. You could damage the sensor and cause injury or an allergic
reaction to yourself or others.
If you experience problems with battery charging or function, visit Zen-Me Support (zenme.io/support).
Zen-Me Sensors contain built-in wireless re-chargeable Lithium Polymer (Li-Po) batteries.
Only charge your Zen-Me Sensor using the approved Zen-Me Charger. Only charge using an adapter that is compliant with applicable
country regulations and international and regional safety standards, including the international Standard for Safety of Information
Technology Equipment (IEC 60950-1).
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 5
↑ GO TO CONTENTS
Prolonged Heat Exposure
Radio Frequency Radiation Exposure
Choking Hazard
Prolonged physical contact with a Zen-Me Sensor, Zen-Me Charger, power adapter or charging cable when plugged into a power source
may cause heat exposure, discomfort or injury. Avoid sitting, resting or sleeping on the Zen-Me Sensor or Zen-Me Charger when connected
to a power source or charging is taking place, either in direct contact or if the devices are under clothing, blankets or pillows. Take special
care if you have a physical condition that aects your ability to detect heat against your body.
Zen-Me Sensors, Zen-Me Chargers and Zen-Me Pendants are not toys and must always be kept out of the reach of small children, people
with reduced physical or mental ability and pets.
Zen-Me Sensors and Zen-Me Pendants contain small parts which may present a choking hazard or cause other injury to small children,
people with reduced physical or mental ability and pets.
Zen-Me Sensors may become accessible and pose a hazard without warning if accidentally released from holders, clips or pendants.
Close supervision is recommended if the Zen-Me Sensor, Zen-Me Charger or Zen-Me Pendant are used by, on or near children or people
with reduced physical or mental ability.
Never put a Zen-Me Sensor, Zen-Me Pendant (including Charm, Chain or Clasp), batteries or other components in the mouth. Swallowing
can lead to serious injury, illness or death.
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
CAUTION
The Zen-Me Sensor is a mobile transmitter and receiver that uses an internal antenna for sending and receiving low-level radio frequency
(RF) energy for data communications. When operating in maximum power output mode, the sensor emits RF energy below the published
limits. To conform with RF exposure compliance requirements, the Zen-Me Sensor should only be used as described in the Zen-Me User
Manual (zenme.io/manual). DO NOT use the sensor in any other conguration or co-locate or operate with other transmitters or antennae.
PRODUCT
Zen-Me Temperature
Zen-Me Humidity
2402-2480
2402-2480
0
0
FREQUENCY BAND (MHz) MAX RADIO FREQUENCY POWER (dBm)

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
PAGE 6
↑ GO TO CONTENTS
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of FCC rules and with ISED license-exempt RSS(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
The symbol on your Zen-Me device or its packaging shows that this is an electronic device and contains a battery. At the end of its life,
your Zen-Me device and battery must be disposed of separately from other household waste. Materials and chemicals in your Zen-Me
device and battery could be harmful to the environment, or cause injury if handled, processed or disposed of irresponsibly. Dispose of
your Zen-Me products and packaging at a recycling centre in compliance with local laws and regulations. To nd out where to recycle your
Zen-Me product, contact your local waste management provider or the retailer where you purchased the product.
Information about product recycling, RoHS, REACH and other environmental compliance programs can be found on the Zen-Me App
(Settings/Disposal).
Regulatory Information
Federal Communications Commission (FCC) Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These
limits aredesigned toprovide reasonable protection against harmful interference ina residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
correct the interference by one of the following measures:
Industry Canada (IC) Information
This Class B digital apparatus complies with CAN ICES-3 (B)/NMB-3(B).
For other regional compliance information, download the Zen-Me App andgotoSettings/Regulatory.
Disposal and Recycling
Disclaimers
Support
•All information within this Safety Guide is subject to change without notice or warning.
•Zen-Me Inc. cannot be held liable for any losses resulting from the use of Zen-Me devices or the Zen-Me App.
•Measurements or data featured in this Safety Guide are based on Zen-Me testing standards.
•Reproduction of this Safety Guide in full or part is prohibited unless authorized by Zen-Me Inc.
For support, trouble-shooting information, Frequently Asked Questions, go to Zen-Me Support (zenme.io/support).
Access discussion boards and tips from the Zen-Me Forum (zenme.io/forum).

© 2020 Zen-Me Labs Ltd. Zen-Me is patented and trademark of Zen-Me Labs Ltd.
Zen-Me Sales Package User Manual Design
Booklet for ZMH01A and ZMT01A