Zenty ZT-116 User manual

[phone] | [e-mail] Page 1of 27 Copyright © Zenty AV
Zenty | Professional A/V Solution Provider
ZENTY ®
9807 EMILY LANE
STAFFORD, TX 77477
[phone]
[email protected]

[phone] | [email protected] Page 2of 27 Copyright © Zenty AV

[phone] | [email protected] Page 3of 27 Copyright © Zenty AV

[phone] | [email protected] Page 4of 27 Copyright © Zenty AV
The ZT-MT88EA is a professional UHD 4K HDBaseT Matrix used for audio/video distribution.
Supporting 8 HDMI inputs, 1 HDMI outputs along with 7 HDBaseT extension outputs, users can
extend and distribute 4K signals up to 131ft., and 1080P signals up to 230ft. Each of the 7
HDBaseT receivers also support 2 HDMI outputs so that users can connect 2 displays to each
receiver for maximum flexibility. All of the HDBaseT receivers are powered by the main transmitter
box via Power over Cable function, helping remove the need for additional power supplies, and
ensuring a clean and neat setup. Manage signal routing and EDID via various control methods, such
as front panel buttons, RS232, IR remote, web interface, and Zenty mobile app. RS232 control port
allows for easy integration with 3rd party control systems. Save up to 8 fully customizable routing
presets for easy operation.
•Incorporates HDBaseT technology
•HDMI 2.0 version supports 4K@60Hz YUV4:4:4, 18G, HDR10
•Route any one of the 8 HDMI Sources to any one of the 8 HDMI Displays
•8 outputs (includes 7*HDBaseT output and 1*HDMI output)
•Transmit up to 230ft. under 1080p, 131ft. under 4K@60Hz
•HDCP 2.2/1.4 compliant
•Wide-band Bi-Direction IR routed control (38~56KHz)
•1 x Analog Audio and 1 x SPDIF Audio extraction output
•Supports RS232 Pass Through
•Front Panel Button with LCD, IR Routing, RS232, TCP/IP, PC Tool Control
•PoC (Receivers powered by HDBaseT Matrix)
•1U rack design with mounting ears
•AC 110V~220V/50HZ/60HZ input

[phone] | [email protected] Page 5of 27 Copyright © Zenty AV
•(1) x Main Unit (HDBaseT Matrix) and 7x Receivers
•(1) x Power Cable
•(1) x Remote control
•(16) x IR Transmitter cables, 16x Wide-Band IR Receiver cables
•(1) x CD for control software & user manual
Operating Temperature Range
-5°C ~ 40°C (23°F ~ 104°F)
Storage Temperature Range
-10°C ~ 60°C (-14°F ~ 140°)
Operating Humidity Range
5 –90% RH (No condensation)
Input Video Signal
0.5 –1.0 volts p-p
Input DDC Signal
5 volts p-p (TTL)
Bandwidth
18Gbps
Video Format Support
4K 60HZ YUV 4:4:4
4K 30Hz, 1080P / 1080i / 720P / 576P /
480P / 576i / 480i
HDCP Compliance
1.4 | 2.2
Video Output
HDMI 2.0 | HDMI 1.4 (Over HDBaseT and
HDMI)
Audio Format Support
PCM, Dolby 5.1, DTS 5.1 digital audio
Maximum Transmission Distance
1080P: 230ft. | 4K: 131ft.
Power Consumption
100W (Max)
Dimensions (L x W x H)
480mm x 348mm x 44mm
18.90” x 13.70” x 1.73”
Net Weight
8.82 lbs.

[phone] | [email protected] Page 6of 27 Copyright © Zenty AV

[phone] | [email protected] Page 7of 27 Copyright © Zenty AV
The signal switch includes 8 free switching channels, which can be configured as input/output
according to the requirements, forming a matrix of 1 x 8 ~ 8 x 1, which can switch any input.
Signal to 1 channel output or all channel output.
The specific operation is as follows:

[phone] | [email protected] Page 8of 27 Copyright © Zenty AV
Switch the input to the output
Operation format: "output channel" + "input channel"
For Example: Output port 2,5,8 switch to input 7
Operation: Press OUT number "2" "5" "8" + IN number "7" to complete the switch
The video interface has two sub menus:
1. Video Switch
2. Video On/Off
The specific operation is as follows:
1. Video Switch:
Switching any output to one input or all outputs to the same input
①Select “Video”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select “Switching”
③Press “ENTER”enter next page
④Press “UP”, ”DOWN”button to select the output (The ninth port means ALL）
⑤Press “ENTER”
⑥Press “UP”, ”DOWN”to select the input
⑦Press “ENTER”, switching is done

[phone] | [email protected] Page 9of 27 Copyright © Zenty AV
2.Video On/Off
Turn on/off any output video or all outputs video
①Select “Video”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select “On/Off”
③Press “ENTER”enter next page
④Press “UP”, ”DOWN”button to select the output (The ninth port means ALL）
⑤Press “ENTER”
⑥Press “UP”, ”DOWN” to select “On” or “Off”
⑦Press “ENTER”, switching is done

[phone] | [email protected] Page 10 of 27 Copyright © Zenty AV
The Audio Control has NINE sub menus:
1. Out 1 ~ Out 8
2. Mute (Default)
The specific operation is as follows:
Audio interface can be set to output Audio (Analog or SPDIF), then choose Audio output or mute
Operating instructions:
Select "Audio" from the main menu and press "ENTER" to confirm
Press the up and down buttons to select "Out" or "Mute" and press "ENTER" to confirm the.
The bottom of the selected state will turn white with white dots at the back

[phone] | [email protected] Page 11 of 27 Copyright © Zenty AV
Specific operations are as follows:
①Select “EDID”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select the input (The “In9”means ALL input)
③Press “ENTER”enter next page
④Press “UP”, ”DOWN”button to select the MODE that you need, then press “ENTER”to
select the EDID
⑤After confirming EDID, specific information of the EDID (resolution, audio, EDID mode) will be
displayed.
SETUP mode can set the device’s RS-232 baud rate, DHCP, Reboot, Factory Specific
operations are as follows

[phone] | [email protected] Page 12 of 27 Copyright © Zenty AV
1. RS-232 Baud Rate setting:
It has 7 kinds of baud rates inside the device: 2400; 4800; 9600; 19200; 38400; 57600; 115200
Default Baud Rate is: 115200
①Select “Setup”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select the “BAUD”and press “ENTER”
③Press “UP”, ”DOWN”button to select the baud rate and press “ENTER” to confirm
2. DHCP On/Off setting (Default OFF)
On means Dynamic; Off means Static
①Select “Setup”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select the “DHCP”and press “ENTER”
③Press “UP”, ”DOWN”button to select “On”or “Off”and press “ENTER” to confirm
3. Reboot setting
①Select “Setup”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select the “Reboot”and press “ENTER”
③Press “UP”, ”DOWN”button to select “No”or “Yes”and press “ENTER”to confirm

[phone] | [email protected] Page 13 of 27 Copyright © Zenty AV
4. Factory setting
①Select “Setup”in the menu and press “ENTER”
②Then use “UP”, ”DOWN”button to select the “Factory”and press “ENTER”
③Press “UP”, ”DOWN”button to select “No”or “Yes”and press “ENTER”to confirm
Check the device information: IP or System information

[phone] | [email protected] Page 14 of 27 Copyright © Zenty AV

[phone] | [email protected] Page 15 of 27 Copyright © Zenty AV

[phone] | [email protected] Page 16 of 27 Copyright © Zenty AV
The matrix can pass the IR signal through the IR system to the HDMI source or pass the IR signal
from the HDMI source to the HDMI sink
Dual way IR setup:
Step 1: “IR IN” is for HDBaseT output, “IR OUT” is for input channel
Step 2: “IR IN EYE” Controlled by all input IR; “IR OUT ALL” Controlled by all output IR.
Step 3: HDBaseT receiver support connect with IR receiver to control the Matrix by remote
Step 4: Matrix IR channel “IR IN EYE” support connect with IR-RX cable to control the Matrix by
remote

[phone] | [email protected] Page 17 of 27 Copyright © Zenty AV
Control software operation:
The serial control software is illustrated with SSCOM32 as an example.
Basic Settings:
Double-click the software in the installation package to run specifically (as shown in
figure 1 below) and install the RS232 software on the computer.
In the parameter configuration area, the serial number of serial port and PC connection
is selected, and the baud rate of the communication protocol is completed: 115200
(default), data location: 8. Stop bit: 1, check bit: no, you can input the instruction in the
command input area and control the machine or remote receiver.
Instructions:
1. All commands start from “#”, command head “%c”: “d” parameters, “l” lock,
“s” save.
2. The “_” in the commands cannot omit. Parameter: %d: 0 means ALL.
3. Command head & Parameter1 & Parameter2... need to add one “SPACE”.
The following table is only an example. Please refer to the list of instructions.

[phone] | [email protected] Page 18 of 27 Copyright © Zenty AV
Please refer to the " Command list" for details.
Example: Output5 switch to input 6 channel off:
Operation format: #video_d out5 matrix=6 onoff=0
1). Connect the Ethernet port of matrix to the Ethernet port on PC by a crossover cable with RJ45
connectors.
2). Configure your PC as follows:
①Click Start > Control Panel > Network and Sharing Center.
②Click Change Adapter Settings.
③Highlight the network adapter you want to use to connect to the device and click Change settings
of this connection.
3). The local Area commotion properties window for Network selection appears as below:
4). Click the Highlight Internet Protocol Version 4 (TCP/IPv4).
5). Click Properties.
6). Select Use the following IP Address for static IP addressing and fill in the details.
For TCP/IPv4 you can use any IP address in the range 192.168.1.1 to 192.168.1.255 (excluding
192.168.1.168).
7). Click OK.
8). Click Close.
Default IP Address: 192.168.1.168;
MASK: 255.255.255.0;
Gateway:192.168.1.1;
MAC:0008-DCCA-CF3F （Each device has a different MAC address)

[phone] | [email protected] Page 19 of 27 Copyright © Zenty AV
1) Enter the default IP address of the matrix: 192.168.1.168.
2) You will see following picture and control:
(User Name: admin; Password: admin)
Note: web control is recommended to use Google, fire fox, IE8 and above browsers,
using other browsers may not be compatible
WEB interface introduction:
1. Icon: the page title label displays the device name or type
2. Status display and description:
2.1 Click the menu bar on the left, you can enter the corresponding operation interface
2.2 After the operation is finished, there is no need to click the button like confirm, and it can
be switched quickly. Please do not click continuously, otherwise the data refresh will be out
of sync
2.3 Video/Audio/EDID interface, input or output button, when there is device active or TV
access the border of the corresponding button is shown as blue
3. Login interface:
Total 5 groups of accounts: accounts and passwords are 5-15 alphanumeric and underlined, other
invalid or correct characters are intercepted; Account admin~admin4 total 4 accounts, password:
admin

[phone] | [email protected] Page 20 of 27 Copyright © Zenty AV
Login page:
Get the IP address of web server according to serial port message /LCD display; To ensure network
connectivity, enter IP address in the browser address bar and click to enter the login interface. Enter
the correct account number and password to enter the interface
Note:
This web set a cookie, when the password and account are correct, if the browser is not closed,
refresh the page again, will automatically log in, if you save the account password into the cookie,
after closing the web page again enter the IP address can directly enter the control page
“VIDEO” interface description:
1. Output selection bar: [01>>0]~[08>>08], input option bar: 01~08 means input port; all means
select all
2. Video switch: First select the output then select input to complete the switch. For example: select
[03>>01], then click 01. Blue box will be displayed when signal source or TV is connected
3. Scenario application
Save: Select any one of preset 1-8, blue means selected, and then click save to complete the save
Apply: select any one of perset1~8 and click Apply again to complete the recall