Zico QUIC-MOUNT QM-ETD-1 Parts list manual

ZICO®
3095PM12
QUIC-MOUNT®DOUble exTrICaTION TOOl HOlDer
MODel QM-eTD-1
ParTs aND INsTrUCTION MaNUal
The QM-ETD-1 holds two (2) extrication tools
securely upright in the compartment.
Fully adjustable, the various components slide to
t your individual tool for a most secure t.
Made with heavy-duty, lightweight aluminum.
Mounts to virtually any at surface.
MODEL DESCRIPTION WT./@ IN LBS.
QM-ETD-1 Double Extrication Tool Holder 14.2
Rev. 12-16-14

Parts Diagram/Breakdown - QM-ETD-1
ITEM # PART # DESCRIPTION QTY.
1 3095-246-101 QMT-ETD Hanging Post 4
2 3095-246-103 QM-ETD Hang Bracket 4
3 3095-246-105 QM-ETD Spacer Plate 2
4 3095-246-107 QM-ETD Channel Short 2
5 3095-246-109 QM-ETD Channel Long 4
6 3095-246-111 QM-ETD Base Angle 2
7 3095-239-103 Hanging Angle Univ. 4
8 9010-102524 1/4-20 x 1.5" Hex Bolt ZPS 10
9 9014-112500 1/4" Washer ZPS 20
10 9013-172501 1/4-20 Low-Prole Nylock Nut 10
11 9010-343116 5/16-18 x 1" Sq Bolt ZPS 8
12 9014-183100 5/16" Washer ZPS - Grade 8 20
13 9013-173100 5/16-18 Nut Nyloc 20
14 9010-343120 5/16-18 x 1.25" Sq Bolt ZPS 8
15 9010-103112 5/16-18 x .75" Sq Bolt ZPS 4
16 9013-373700 3/8-16 Serrated Flanged Nut 8
17 3095-215-109 Strap Handle 2
18 3095-215-107 EPDM Rubber Strap 2
19 9010-162516 1/4-20 x 1" FH Screw 2
20 9013-172500 1/4-20 Nyloc Nut, ZPS 4
21 9014-162500 1/4" Wide Washer 4
22 9010-102520 1/4-20 x 1-1/4" Hex Head Bolt, ZPS 2
Page 2

Adjustment Instructions:
Note: Part numbers in parenthesis (see Page 2)
Set-up: Adjustment is most easily accomplished with the QM-ETD-1 out of the compartment and in full
upright position (as shipped).
1. Loosen 5/16-18 x 1" sq. bolts (11) on Hanging Angle Brackets (7). Adjust brackets until they rest ush
against the blade-end of your tool. Re-tighten bolts.
2. Loosen 5/16-18 x .75" sq. bolts (15) on Short Channel (4). Adjust Short Channel up or down to
accommodate height of your tool. Re-tighten bolts.
3. Loosen 5/16-18 x 1.25" hex bolts on Hang Bracket (2). Slide in or out to accommodate size and shape of
tool handle. For wider handles, reverse the Hang Brackets (see below). Re-tighten bolts.
4. Adjust Rubber Strap (18) so that Strap Handle (17) grips tool handle tightly.
After both sides of bracket have been adjusted to t desired tools, you may adjust tilt angle by removing 1/4"-20
x 1.5" hex bolts (8) and hardware on one side of the Base (6) and repositioning Long Channel (5). Re-tighten
hardware via appropriate holes in Base after achieving desired tilt.
Mounting Instructions:
Mount at four points using 3/8" hardware (not included).
Page 3

Ziamatic Corp.
10 West College Avenue, P.O. Box 337, Yardley, PA 19067-0587 • [phone] • FAX: [phone]
*ZICO is a registered trademark for re, safety and marine products made by Ziamatic Corp.Copyright Ziamatic Corp. 12-14
www.ziamatic.com
TOLL FREE: 800-711-3473
Page 4