Zip HydroTap 801621 User manual

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 1 of 20
ZIP HydroTap
User Guide
®
• Tap Operation...................(Pages 2-5)
• LCD Screen & Menu .......(Pages 6-17)
• Maintenance.................... (Page 18)
• Menu Icons.......................(Page 19)
• Date of Installation.........
Affix Model Number Label
Here
801621

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 1 of 20
ZIP HydroTap
User Guide
®
• Tap Operation...................(Pages 2-5)
• LCD Screen & Menu .......(Pages 6-17)
• Maintenance.................... (Page 18)
• Menu Icons.......................(Page 19)
• Date of Installation.........
Affix Model Number Label
Here
801621

Page 2 of 20 801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09
Safety Lock
3. Tap operation
Safety - Boiling Models
B
A safety lock feature is provided to pre-
vent boiling water flowing if any of the
hot levers are inadvertently operated.
To dispense boiling water
(With the Safety ON)
Depress the Red lever, while
simultaneously covering the safety lock
button with a second finger. These two
actions need to occur within 2 seconds
for the successful dispensing of boiling
water.
The Safety Lock button can only be
Disabled or Enabled from the LCD
touch screen (Located on the unit in the
cupboard).
NOTE:
When Disabled, no water will be dispensed from the Boiling Hydrotap.
Boiling Water Lever:
(With the safety OFF)
Depressing the “Red” lever allows the
dispensing of boiling water.
Pulling forward the Red lever allows the
tap to operate in a “no-touch” mode.
Water will flow from between 5 and 15
seconds, this is user adjustable (see
page 17).
To reset, return the lever to the “Off”
position and repeat the step. The lever
has to be manually returned to the “Off”
position.
Press or pull lever
Boiling Models
To set the safety using the touch screen:
1. Press the [MENU] button for
main menu.
2. Press the [Setting] button.
3. Press the [Safety] button.
4. Press button to Enable /
Disable, the safety lock feature.
B

Page 2 of 20 801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09
Safety Lock
3. Tap operation
Safety - Boiling Models
B
A safety lock feature is provided to pre-
vent boiling water flowing if any of the
hot levers are inadvertently operated.
To dispense boiling water
(With the Safety ON)
Depress the Red lever, while
simultaneously covering the safety lock
button with a second finger. These two
actions need to occur within 2 seconds
for the successful dispensing of boiling
water.
The Safety Lock button can only be
Disabled or Enabled from the LCD
touch screen (Located on the unit in the
cupboard).
NOTE:
When Disabled, no water will be dispensed from the Boiling Hydrotap.
Boiling Water Lever:
(With the safety OFF)
Depressing the “Red” lever allows the
dispensing of boiling water.
Pulling forward the Red lever allows the
tap to operate in a “no-touch” mode.
Water will flow from between 5 and 15
seconds, this is user adjustable (see
page 17).
To reset, return the lever to the “Off”
position and repeat the step. The lever
has to be manually returned to the “Off”
position.
Press or pull lever
Boiling Models
To set the safety using the touch screen:
1. Press the [MENU] button for
main menu.
2. Press the [Setting] button.
3. Press the [Safety] button.
4. Press button to Enable /
Disable, the safety lock feature.
B

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 3 of 20
Boiling Ambient Models
The operation of the safety lock button can be allowed [Yes] from the touch
screen display.
Once allowed [Yes], the safety feature may then be activated or deactivated
from the tap or Enabled /Disabled from the display screen using button
If dis-allowed [No], Then no changes to the safety on the tap, or on the screen
will be possible.
To change the safety using the touch screen:
1. Press the [MENU] button for
main menu.
2. Press the [Setting] button.
3. Press the [Safety] button.
4. Press button to Enable /
Disable, the safety lock feature.
NOTE: When Disabled, boiling water may be dispensed from the Hydrotap.
NOTE: See Page 16 for safety setting changes and Hot Isolation
instructions.
3. Tap operation
To activate the safety (From the tap):
First place a finger on the safety lock, then depress the Blue lever, while
keeping both fingers in position for a period of approximately ten seconds.The
safety lock indicator light will now be illuminated.
To deactivate the safety (From the tap):
First place a finger on the safety lock, then depress the Blue lever, while
keeping both fingers in position for a period of approximately ten seconds.
The safety lock indicator light will now extinguish.
Safety - Boiling Ambient Models
B
B
Ambient Water Lever:
Depressing the “Blue” lever allows
the dispensing of Ambient water.
Pulling forward the Blue lever allows
the tap to operate in a “no-touch”
mode. Water will flow from between
5 and 15 seconds, this is user
adjustable (See page 17). To reset,
return the handle to the “Off” position
and repeat the step. The lever has
to be manually returned to the “Off”
position.
Press or pull lever

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 3 of 20
Boiling Ambient Models
The operation of the safety lock button can be allowed [Yes] from the touch
screen display.
Once allowed [Yes], the safety feature may then be activated or deactivated
from the tap or Enabled /Disabled from the display screen using button
If dis-allowed [No], Then no changes to the safety on the tap, or on the screen
will be possible.
To change the safety using the touch screen:
1. Press the [MENU] button for
main menu.
2. Press the [Setting] button.
3. Press the [Safety] button.
4. Press button to Enable /
Disable, the safety lock feature.
NOTE: When Disabled, boiling water may be dispensed from the Hydrotap.
NOTE: See Page 16 for safety setting changes and Hot Isolation
instructions.
3. Tap operation
To activate the safety (From the tap):
First place a finger on the safety lock, then depress the Blue lever, while
keeping both fingers in position for a period of approximately ten seconds.The
safety lock indicator light will now be illuminated.
To deactivate the safety (From the tap):
First place a finger on the safety lock, then depress the Blue lever, while
keeping both fingers in position for a period of approximately ten seconds.
The safety lock indicator light will now extinguish.
Safety - Boiling Ambient Models
B
B
Ambient Water Lever:
Depressing the “Blue” lever allows
the dispensing of Ambient water.
Pulling forward the Blue lever allows
the tap to operate in a “no-touch”
mode. Water will flow from between
5 and 15 seconds, this is user
adjustable (See page 17). To reset,
return the handle to the “Off” position
and repeat the step. The lever has
to be manually returned to the “Off”
position.
Press or pull lever

Page 4 of 20 801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09
MixerTap
Lifting the handle up will increase the flow rate and lowering the handle will
decrease the flow rate. Lower the handle all the way down to turn the tap off.
When the handle is moved towards the blue dot, the temperature is
decreased and when moved towards the red dot, the temperature is
increased. The final temperature will be dependant on the temperature of the
incoming cold water.
The spout may be swivelled, left or right, for convenience.
Increase flow
Decrease flow
Cold
Hot
3. Tap operation
Procedure:
• Shield the HydroTap from any direct sun
light using a dark cloth.
• With the unit in Normal operating mode
• Turn the power OFF
• Pull both tap levers to the forward position
• Turn ON the power
• The unit will calibrate the safety switch
• Return the levers to the neutral position.
Light intensity varies from site to site, therefore it is recommended that a
re-calibration be performed at the time of the installation.
All direct natural sun light must be shaded from the HydroTap, during the
calibration. This can be achieved by closing any nearby curtains, blinds, etc.
Pull both levers forward
Safety Sensor Calibration
Safety
sensor

Page 4 of 20 801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09
MixerTap
Lifting the handle up will increase the flow rate and lowering the handle will
decrease the flow rate. Lower the handle all the way down to turn the tap off.
When the handle is moved towards the blue dot, the temperature is
decreased and when moved towards the red dot, the temperature is
increased. The final temperature will be dependant on the temperature of the
incoming cold water.
The spout may be swivelled, left or right, for convenience.
Increase flow
Decrease flow
Cold
Hot
3. Tap operation
Procedure:
• Shield the HydroTap from any direct sun
light using a dark cloth.
• With the unit in Normal operating mode
• Turn the power OFF
• Pull both tap levers to the forward position
• Turn ON the power
• The unit will calibrate the safety switch
• Return the levers to the neutral position.
Light intensity varies from site to site, therefore it is recommended that a
re-calibration be performed at the time of the installation.
All direct natural sun light must be shaded from the HydroTap, during the
calibration. This can be achieved by closing any nearby curtains, blinds, etc.
Pull both levers forward
Safety Sensor Calibration
Safety
sensor

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 5 of 20
Filter light
Filter Change Light Off:
This indicates the filter is operating
within its normal specified lifespan.
Filter Change light flashing
slowly:
The light will flash slowly when the
filter is due for replacement and the
LCD will show “Filter Change”. Refer
to “Replacing the filter” in section ‘C’
of this document.
Filter light
3. Tap Lights
Blue Lights
Blue Ambient water
Lights
On all the time:
This indicates that the Ambient water
is ready.
Red Lights
Red Boiling Water Light
On all the time:
This indicates that the boiling water is
ready.
Flashing slowly:
This indicates that the boiling water is
below the desired temperature.
Wait for the light to stop flashing
before dispensing water. The flashing
light will typically occur after switching
on, or coming out of sleep mode.

801621 - B, BA, BHA, BAHA, - HydroTap User Guide - August 2014 - V1.09 Page 5 of 20
Filter light
Filter Change Light Off:
This indicates the filter is operating
within its normal specified lifespan.
Filter Change light flashing
slowly:
The light will flash slowly when the
filter is due for replacement and the
LCD will show “Filter Change”. Refer
to “Replacing the filter” in section ‘C’
of this document.
Filter light
3. Tap Lights
Blue Lights
Blue Ambient water
Lights
On all the time:
This indicates that the Ambient water
is ready.
Red Lights
Red Boiling Water Light
On all the time:
This indicates that the boiling water is
ready.
Flashing slowly:
This indicates that the boiling water is
below the desired temperature.
Wait for the light to stop flashing
before dispensing water. The flashing
light will typically occur after switching
on, or coming out of sleep mode.