Hot Tap HP™ Shower
Enjoy this all season shower
built with the most durable
components to deliver the
most comfortable showers
for anytime and anywhere!
Item# 6125
INSTRUCTION MANUAL
1067 Portable Battery Powered Pump
zodi.com800-589-2849
SET-UP
1. Attach shower hose end to pump by twisting hose onto barbed
tube of pump. Open battery case lid and load 4 new D Cell
alkaline batteries into portable battery case. Securely close the
lid and lock the battery case latch making sure that the rubber
gasket is in place. Check pump operation by holding pump in
hand while pushing red ON/OFF button on battery case. You
should be able to feel and hear pump spinning. If pump fails to
operate, open battery case lid, gently bend tabs out, check that
batteries are installed correctly and close lid again. Pump will not
be harmed by operating out of water. Do not use old batteries or
mix old and new batteries. Do not mix alkaline, carbon-zinc, or
rechargeable batteries.
2. Before use, squeeze any kinks from hoses.
For showers: Completely submerge pump in water source (e.g.,
in a bucket or lake). Shake pump under water to release any
trapped air. Do not submerge battery case in water.
Bilge Pump: Attach to Zodi hose. Place pump in the lowest part
of the boat and position output end of hose over the side of the
boat. Pump is a recreational grade back-up only and should not
be used as primary bilge or relied upon in life-saving situations.
For best bilge performance, remove showerhead from hose.
3. Push the red ON/OFF button on battery case to establish water
flow from Zodi hose or showerhead. Water should be flowing from
output hose within 20 seconds, if not, apply suction to the end of
the hose to release vapor lock. DO NOT place the pump directly on
sandy river or lake beds. Place the pump on top of pebbles or rocks.
To prevent waves from pushing pump onto shore, place a small
rock on hose near pump, making sure water flow isn’t constricted.
If water flow is low, replace batteries or clean debris screen by
unscrewing cap on pump.
SHOWERING
Turn pump on. Water will begin spraying from hose or showerhead.
Conserve water by placing hose or showerhead in water bucket
between uses or turn off water flow by turning off pump. To turn
off pump, push red button on battery case. See www.zodi.com for
Instant Hot Shower Heater.
SHUT DOWN
Turn power off on battery case. Drain water from hoses and
showerhead. After use, unscrew pump cap, clean foam debris
screen and rinse pump in clean water. Remove batteries before
long term storage.
TECH SUPPORT
If you are having a problem with your Zodi™ Battery Powered
Portable Pump please do not return it to the store. First, replace
the batteries with new ones, making sure tabs inside battery
case are bent outward to make good contact with top and bottom
of batteries.
If pump is still not operational, call Zodi™ at 800-589-2849.
Most problems can be corrected over the phone.
CAUTION: Pump must always be submerged when operating. Do
not mix old and new batteries. Do not mix alkaline, carbon-zinc, or
rechargeable batteries.
Note: These directions also apply to the Zodi™ Battery Powered
Shower and the Zodi™ Battery Powered Bilge Pump.
Assembled in China. Designed in Park City Utah USA.
RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
Zodi™ Zip Portable Shower
Enjoy a portable, instant Hot
Shower with the Zodi Zip.
Features all metal heater,
powerful pump and can be
used with any water source!
Item# 3920
Hot Tap™ Shower
Our best selling
on-demand water
heater and hot shower.
Enjoy unlimited hot
water in seconds.
Item# 6185
Pat. Pend.
ZODI™ UPGRADES
Pat. Pend.
Pat. Pend.
