ZooZ ZEN52 LR User manual
Secure your Z-Wave relay and the wall switches in the box
with mounting screws, handling the wires with care.
Install the wall plate and restore power to the circuit.
COMPLETE INSTALLATION
The LED indicator should start blinking green when you turn
the power back on. Toggle the switch connected to each
relay to check if the load changes state. If the test fails,
please check that:
Ÿpower is fully restored to the circuit
Ÿwiring matches the instructions exactly
Ÿthe load isn’t too large and overheating the relay causing it
to shut off.
TEST THE RELAY
ŸThis product should be installed indoors upon completion of
any building renovations.
ŸPrior to installation, the device should be stored in a dry, dust-
and-mold-proof place.
ŸDo not install the relay in a place with direct sun exposure, high
temperature, or humidity.
ŸKeep away from chemicals, water, and dust.
ŸEnsure the device is never close to any heat source or open
flame to prevent fire.
ŸEnsure the device is connected to an electric power source that
does not exceed the maximum load power.
ŸNo part of the device may be replaced or repaired by the user.
WARNING
SPECIFICATIONS
DOUBLE RELAY ZEN52 LR
USER MANUAL
FEATURES
ŸManual or Z-Wave on/off control of 2 individual loads up to 5A
ŸInstalls behind your existing wall switches (single pole or 3-way)
ŸSmall form factor to easily fit in a crowded switch box
ŸNEW: Z-Wave Long Range for a next-level wireless network
ŸScene control: trigger actions with multi-tap (select hubs only)
ŸRemembers and restores on/off status aer power failure
ŸBuilt-in Z-Wave timer functionality and signal repeater
ŸWorks with LED and incandescent bulbs
Ÿ700 series Z-Wave and SmartStart S2 Security for a safe network
ŸModel Number: ZEN52 LR
ŸPower: 100-240V~, 50/60Hz
ŸMaximum Load: , 500W incandescent, 5A 150W LED or CFL bulbs
resistive, HP motors per channel
ŸRange: Up to 300 feet line of sight
ŸOperating Temperature: 32-104° F (0-40° C)
ŸInstallation and Use: Indoor only
WIRING: READ IT!
This relay is intended for installation in accordance with the
National Electric Code and local regulations. It is recommen-
ded that a licensed electrician perform this installation.
BEFORE YOU INSTALL
www.getzooz.com
ask@getzooz.com
1. CHECK THE LOAD: don’t exceed 150W for LED’s, 500W for
incandescent, or 5 A for resistive loads per relay, DO NOT
CONNECT THIS DEVICE TO SWITCHED RECEPTACLES.
2. POWER OFF: turn the circuit power off in the breaker panel
before you start. If installing in a multi-switch box with
multiple circuits, turn power off at all of the circuits.
3. ONE CIRCUIT INSTALLATION: the 2 loads you’re planning
to control with your ZEN52 need to be on the same circuit!
4. CHECK THE WIRES: mark load (most oen black), line
(most oen black), neutral (most oen white), and ground
(most oen bare) for each switch. 14 AWG wires only! Don’t
rely exclusively on your multimeter to identify the wires!
4. DISCONNECT THE OLD SWITCHES: remove the wires and
label them accordingly.
5. CONNECT THE Z-WAVE RELAY: follow all installation steps
carefully. Wire the relay EXACTLY like in the diagram.
µNOT SURE WHAT YOU’RE SEEING? WE’LL HELP! SUPPORT.GETZOOZ.COM
SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
1 Keep your existing wall switches connected to ground.
ZEN52 WIRING DIAGRAM FOR SINGLE POLE INSTALLATION
2 Connect the power source to the L black pigtail on the
ZEN52 and the load wires to the OUT1 red and OUT2
blue pigtails for each load. Load and line CAN’T be
swapped so make sure you identified them correctly!
3 Connect the N white pigtail to the bundle of neutral
wires.
PAGE 1
ON/OFF SWITCHES ONLY
Do not connect the Z-Wave relay to a wall dimmer,
illuminated switch, or an electronic add-on switch. The
ZEN51 relay can only be wired with mechanical on/off or
momentary switches in single pole, 3-way, or 4-way settings!
4 Connect the wall switch terminals to the S1 yellow and
S2 brown pigtails on the ZEN52 and to the power source
for each switch respectively .
NEED MORE DIAGRAMS?
Scan the QR code for 3-way wiring
diagrams and more installation tips.
QUESTIONS?
ask@getzooz.com
PAGE 2
CAUTION
This is an electrical device - please use caution when installing and
operating the relay. Remote control of appliances may result in
unintentional or automated activation of power.
Do not use this Z-Wave device to control electric heaters or other
appliances which produce the risk of fire, burns, or electrical shock
when unattended.
To reduce risk of overheating and possible damage to other equipment,
do not install this unit to control a receptacle; a motor-operated
appliance; a fluorescent lighting fixture; or a transformer-supplied
fixture.
REGISTER your device for extended warranty and more perks:
www.getzooz.com/register
Z-WAVE CONTROL
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web
interface).
Not sure how? Scan one of the QR codes
below for step-by-step instructions or get in
touch: www.support.getzooz.com
The SmartStart security PIN is located on the back
of the relay, next to the Z-Wave Plus logo.
The LED indicator will blink green to signal communication
and turn green for 2 seconds if inclusion is successful or turn
red for 2 seconds if the pairing attempt fails.
TAP THE Z-WAVE BUTTON 3 TIMES QUICKLY
2. Finalize inclusion at the relay.
if using traditional Z-Wave inclusion.
SCAN THE QR CODE / ENTER THE 5-DIGIT PIN
if using the new SmartStart method.
1. Bring your Z-Wave gateway (hub) close to the relay if
possible
2. Put the Z-Wave hub into exclusion mode (not sure how to
do that? ask@getzooz.com)
3. Click the on the relay 3 times quickly (the Z-Wave button
LED indicator will start blinking green)
4. Your hub will confirm exclusion, the LED indicator on the
relay will turn green for 2 seconds, and the device will
disappear from your controller's device list.
EXCLUSION (REMOVING / UNPAIRING DEVICE)
FACTORY RESET
If your primary controller is missing or inoperable, you may
need to reset the device to factory settings. To reset the relay,
click the Z-Wave button once and immediately aer,
press and hold the button for 15 seconds. The LED
indicator will flash during the process and turn red for 3
seconds to confirm successful reset.
NOTE: All previously recorded activity and custom
settings will be erased from the device’s memory.
TROUBLESHOOTING
The relay won’t add to your system? Try this:
1. Initiate EXCLUSION and click the Z-Wave button 3 times
quickly.
2. Click the Z-Wave button 4-5 times quickly to add.
3. Bring the gateway controller (hub) closer to the relay, it
may be out of range.
4. Get troubleshooting tips for your hub at
www.support.getzooz.com
The relay won’t control the load manually anymore? Try
this:
1. Turn the power off at the breaker and check if a wire
didn’t get loose.
2. Exclude the relay from the hub or reset it in case manual
control was accidentally disabled.
3. The load may be incompatible so try it with a single
incandescent bulb.
Hubitat
Choose your hub and scan the QR code with your phone’s
camera. Then click on the link to access the step-by-step
pairing instructions.
Get more tutorials and helpful tips at ww.support.getzooz.com
Home Assistant
NEED SOME HELP? ask@getzooz.com
ADVANCED SETTINGS
ASSOCIATION
This Double Relay supports Group 1 with up to 5 devices for
Lifeline Group communication, Group 2 and Group 3 with up
to 5 devices. This device will send BASIC REPORT and
SWITCH BINARY REPORT to Group 1 and BASIC SET
command to group 2 (for S1) and 3 (for S2) when operated
manually from the wall switch. You can set direct association
to have the relay control another Z-Wave device
independently of the hub by using Group 2 or Group 3. Not
every hub exposes direct association settings in the interface
so please go to www.support.getzooz.com to see if your
system allows for direct association.
This product can be included and operated in any Z-Wave network
with other Z-Wave certified devices from other manufacturers
and/or other applications. All non-battery operated nodes within
the network will act as repeaters regardless of vendor to increase
reliability of the network.
This product features the latest Security 2 (S2) framework to
remove smart home network hacking risks. This device is equipped
with a unique authentication code for trusted wireless
communication.
This is an ETL certified device. ETL, just like UL, is a Nationally
Recognized Testing Laboratory. The ETL mark is proof of product
compliance with North American safety standards.
WARRANTY
This product is covered under a 12-month limited warranty and a
5-year extended warranty once registered. To read the full warranty
policy or file a warranty claim, please go to
www.getzooz.com/warranty
IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT,
INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS,
REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT,
OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ'S LIABILITY AND
CUSTOMER'S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS
AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT
LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY
LIMITED TO, AT ZOOZ'S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT
PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND
ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED
WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ'S DELIVERY, OR THE DATE FIXED
FOR DELI-VERY IN THE EVENT OF NONDELIVERY.
FCC NOTE
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED
MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT
IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1. This device may not cause harmful interference,
2. This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according
to instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in any given installation.
If this equipment causes harmful interference to radio or television reception, the user may try to correct the
interference by taking one or more of the following measures:
- Reorient or relocate receiving antenna
- Increase the separation between equipment and receiver
- Connect equipment into a separate outlet or circuit from receiver
- Consult the dealer or an experienced radio/TV technician for additional assistance
All brand names displayed are trademarks of their respective holders.
© Zooz 2023PAGE 4PAGE 3
Z-Box Hub
Here is a selection of settings available to customize your
relay. Scan the QR code for a full list of parameters and
look below for how to access them on your hub.
ŸTimer to automatically turn the relay on
or off aer a set period of time
ŸSmart Bulb Mode (disable the relay)
ŸExternal switch type
ŸOn/off status aer power failure
Hubitat
Choose your hub and scan the QR code with your phone’s
camera. Then click on the link to learn how to access and
change the advanced settings for the relay on your hub.
Home Assistant
SCAN SETTINGS
Z-Box Hub
S2
SmartThings
SmartThings
Other ZooZ Relay manuals
